What is the process of Mercedes Benz R350 tire pressure reset?

Mercedes Benz R350 tire pressure.

Reset process:

1. First open the door, then find the ignition switch, and then rotate it to the [on] mode, so that the indicators on the instrument are lit;

2. Then press and hold the steering wheel.

The [OK] button on the left side, press it once to release it, don't keep pressing, otherwise it will be invalid, and then press the right button to the maintenance interface;

3. After displaying the maintenance interface, press the downward indicator key on the steering wheel again, and you don't need to press it all the time, just press it to get to the interface of tire pressure;

4. After the instrument prompts [Low Voltage Continuation Indicator] to be activated, then press the [OK] button on the steering wheel to confirm;

5. After that, the dashboard will prompt [whether the tire pressure is normal], then press the indicator button to select [Yes], and then press the OK button to confirm;

6. After the tire pressure reset operation is completed, turn off and restart the engine until the tire pressure reset is successful.

First of all, there are two major function buttons on the steering wheel, as shown below

There are up and down buttons on the left side of the steering wheel, and the display interface switch button.

The next step is how to eliminate the tire pressure light

First of all: through the switch button on the left button of the steering wheel, adjust the LCD display of the instrument to the kilometers interface.

When the interface in the above picture appears, then press the up and down buttons on the left side of the steering wheel to adjust to the interface below, <> the English in the picture reminds you that if you want to activate the tire pressure function, you need to press the "R" button.

At this time, we will notice that there is an "R" button on this display. The "R" button is actually the reset button for the mileage, and it will be set in different places for different cars. As shown in the figure below.

So, let's press the R button. Then the following interface appears, <> this English means, whether to activate the tire pressure function. If it is, press the "+" key, and if it is not activated, it will be the "—" key.

Let's press the "+" key.

"It's a white bottom, at this time, wait for about three seconds, the tire pressure will be automatically activated, at this time, you need to travel dozens of meters to a few kilometers to let the computer readjust to the new tire pressure, and then it's OK.

In general, the tire pressure light is correct, but the alarm after a bump is not relevant in many cases. It is recommended to pay more attention in the future, it is more dangerous to run at high speed with injuries.

Here's a copy: Turn off the key. Do not pull out the key.

Then press the lock and unlock together until the power is turned on! The car beeped. You get out of the car and see if the turn light on the left is on.

Then grab your barometer and follow the turn lights to deflect that tire! During the deflation, I heard a horn, and the turning light jumped to the right to put 4 tires in turn. When you finish doing it, the air pressure light goes out.

Then refill the air according to the system pressure value.

Hello. Do a little ECU setup and you're good to go. Hope it helps.

wheelTire pressureThe tire pressure needs to return to normal before the tire pressure data can be reset. The vehicle is energized and utilizedSteering wheelon the Select button to find the "Maintenance" option in the trip computer. Find "Tire" in the menu of maintenance options and enter it, then the trip computer will prompt "Use the current air pressure value as a new reference value", and then press the "OK" button on the steering wheel to complete the reset.

The tire pressure of the car is between 230-250kPa is the normal range, however, the specific normal tire pressure of the car should also be subject to the recommended value of the car factory, which can generally be found in the car owner's manual, the label next to the cab door (near the B-pillar), the drawer next to the driver's seat of the vehicle, and the small door of the fuel tank cover. It will be marked in great detail with the specific tire pressure used.

Press the multi-function button on the left side of the steering wheel, bring up the menu interface in the instrument, select the maintenance option, and then through the steering button of the steering wheel, select "Tire inflation pressure" and press the "OK" button, wait for the instrument to display "After driving for a few minutes, the tire pressure will be displayed", press the flip button, the instrument will display "Use the current pressure as a new standard value", at this time, press the "OK" button.

Hello, in the multifunction steering wheel.

Re-set the tire pressure fault light, press the set button with tire pressure identification on the far right side of the front of the gear lever for a long time, if the tire pressure is normal, the alarm light can be eliminated, you can press and hold the tire pressure monitoring button until the light goes out, so that it is eliminated and then press the tire pressure monitoring button until the light is on, so that it is set up again, and it can be eliminated by setting it inside the multi-function steering wheel rental source, or using a computer detector to reset and eliminate.

Reset method when the tire pressure warning light is on:

1. Press the "Menu" button on the turn indicator lever, select the "Tire Pressure Display" item in the "Stroke Fuel Information Menu", and press the SET CLR button;

2. The driver information center will display "Tire pressure from new learning", select "Yes" to guess, press the SET CLR button, and the horn will sound 2 times. The Driver Information Center will display "Tire Pressure Learning Enabled";

3. At this time, the left front turn indicator will be on, and after increasing (or decreasing) the air pressure of the left front tire, the operation of pressurization (or decompression) can be stopped after the horn sounds.

4. Then "the right front turn indicator will be on", the right rear and left rear indicators will be lit in order, and the remaining 3 tires will be repeatedly pressurized or depressurized;

5. After the operation of the four tires is basically completed, the turn indicator will be on for 3 seconds, and the horn will sound 2 times, which means that the tire pressure learning is completed; Adjust the tire pressure to the required value, at this time the tire pressure displayed in the information center is the actual tire pressure, do not worry about the tire malpractice omen pressure gauge to measure, the error is not too large if it is done.

Hope it helps, hope!

1. Open the key, use the main menu key, and select the kilometers menu.

2. Press the Up button on the left side of the steering wheel and select the Run Flat Indicator Active Menu R-button.

3. Press the R button in the middle of the meter.

4. Press + or - on the right side of the steering wheel.

5. Select yes and turn off the key to complete.

Turn on the key, adjust to the total kilometers interface, press the up button on the left side of the steering wheel, then press the R button on the upper part of the instrument, and then press the button on the right side of the steering wheel, and the reset will be successful.

Mercedes-Benz R350 tire pressure, it is automatic can be paid, right? Don't worry about it yourself.

It will be easy to understand at a glance, and it will be clear at a glance, thank you