How to paste tile wall tiles firmly, neatly and beautifully?

1. When the base layer is treated, all kinds of dirt on the wall should be cleaned up, and watered and moistened one day in advance. If the base layer is a new wall, when the cement mortar is dry, it should be arranged with bricks, elastic lines, and pasted surface bricks.

2. Before the formal paste, the standard point must be pasted to control the flatness of the pasting surface, and the flatness should be checked with a ruler at any time during operation.

3. Before pasting the tiles, they must be soaked in clean water for more than two hours, and the bricks should be taken out to dry for later use. When pasting, paste from bottom to top, require the mortar to be full, when the ash is lost, it must be removed and re-glued, and it is not allowed to plug the ash from the brick joints and mouths.

4. When laying and sticking, when encountering pipelines, lamp switches, and supporting parts of toilet equipment, etc., they must be cut and matched with a whole brick sleeve, and it is forbidden to use non-whole bricks to patchwork and paste. The whole or independent parts should be pasted at one time, and when it cannot be completed at one time, the stubble should be left at the construction joint or the dark corner.

How to paste wall tiles:

1. Leveling: When paving wall tiles, the surface of the paved wall should be treated, the surface dirt should be removed, and sprinkled with water to moisten, and then leveled with cement mortar, and then paved after the leveling layer is completely dry.

2. Pull the line: according to the requirements of the design paving pattern, determine the brick plan, pull the marking line on the dry leveling layer, and the purpose of the line is to keep the joints of the tiles paved and straight, so that the tiles are on a vertical plane.

3. Soaking in water: The wall tiles are completely placed in clean water, generally 30 minutes, and the specific soaking time is subject to the fact that the tiles do not bubble, and then take out the water stains to dry for later use.

4. Mixing: 425 cement (i.e. cement) is selected for paving glazed wall tiles, and the sand is better in medium sand, and the cement and sand are stirred into a paste with water at a ratio of 1:3.

The grade of cement should not be too high, otherwise the later stress of cement mortar will cause the glaze of the brick to crack, resulting in engineering quality accidents. The mixing ratio of cement is too high and will also lead to the above situation, it is recommended to mix according to the ratio of fly:3 as well.

5. Paving: Spray enough water on the wall, evenly smear the cement mortar on the back of the glazed brick to be used (the mixed cement mortar in step 4), the thickness of the mortar is 5mm-6mm, and the large-size glazed wall tiles are appropriately thickened when paving, and the wood is gently patted firmly to make it smooth, and the level is used to find the apple at any time.

6. Inspection: After the tile paving is completed, the hollow drum of the tile should be checked, and the wooden handle of the small shovel knife can be checked by hitting the brick surface.

7. Grouting: After the tile paving is completed, use a special tile grout agent for grouting.

How to put a tile wall? Cut neatly and look good. Paste the tiles on the original wall. You should stick it according to your own requirements.

As long as the tiles and wall tiles are pasted, the husband is neat and good-looking, and it is quite good to find a master to paste the tiles.

If you want to make the tile paste effect particularly good, then we must choose the best products. If the quality of the tiles is not good, it will not be well guaranteed when it is laid. We can choose tiles with good gloss, uniform color and very clear appearance, so that the quality of the tiles will be better.

If we want to be more detailed, we can listen to the sound of the tile, if it is crisp and not dull, it means that the quality is better, and we can achieve a better laying effect by buying this kind of tile.

The wall should be painted flat before tiling, but also within the same horizontal line, and some water can be sprayed on the wall before tiling, so that the tiles are very strong.

Paste some water on the back of the tile, and then dilute the cement goods, so that you can paste the best effect, and there are many kinds of patterns for tiles.

You can use some strong adhesives, so that the adhesive effect is relatively good and very strong.

Choose some very good materials, choose some tiles with low water absorption, which can meet the needs of your own home floor tiles. It also needs a certain support point, and it is also possible to use the dry paste method.

How to paste tiles, strong and good-looking, before pasting, you should do a facial cleaning on the wall. Before the wall tile is paved, the base layer needs to be cleaned first, and the old paint on the wall needs to be removed first, and then evenly painted with the interface, and the interface agent can fully soak the surface of the base layer, improve the adsorption force of the plastering layer and the base layer, and avoid plastering. Let it drink enough water before laying it.

The fine void inside the tile has a certain water absorption, and the tile needs to be completely soaked in the water before paving, and soaked in water until the surface is no longer bubbled, and the water is soaked to prevent it from absorbing the moisture of the cement mortar, resulting in hollowing and falling off. The shop should be pre-arranged, and the paving should be smooth. Before tile paving, it is necessary to carry out the pre-typesetting of the socks in the construction space, and it is easy to have color difference and unsmooth lines without pre-typesetting, and the sensory effect is poor.

When the tile is paved, the height of the four corners should be within the limit; Yin and Yang Angle .Don't be too intimate between the tiles.

Many people in the process of decorating the house, will lay tiles on the ground, but many owners do not know much about the paving method of tiles, resulting in various problems when paving tiles, and do not know how to deal with problems when encountering problems, so how to stick the all-ceramic wall tiles firmly? What are the precautions for all-ceramic tile paving? Let's take a look at Sen Sell!

1. How to stick the all-ceramic wall tiles firmly.

First of all, the wall needs to be cleaned, and the wall should not have dust and gaps; Spray water on the wall and evenly apply cement powder to the wall to increase the viscosity between the tile and the wall; After applying the cement mortar, lay the tiles from the bottom to the top, and wait for the cement mortar to dry completely after laying it.

Second, all-ceramic tile paving precautions.

1. When paving the all-ceramic tiles, there is no need to soak the all-porcelain tiles in water in advance, because the all-porcelain tiles cannot be brushed after soaking in water. During the construction of all-ceramic tiles, the adhesive must be painted, and it needs to be placed for about two hours after painting, so that the adhesive can fully penetrate into the all-ceramic tile.

2. When laying all-ceramic tiles, there must be gaps, because the all-ceramic tiles will expand when heated, and shrink when cold. In addition, due to the relatively long firing time of all-ceramic tiles, there will be a slight deformation of the bridge, and the joints can make the tiles more smooth.

3. Before paving the all-ceramic tiles, be sure to check whether the wall is flat, if the wall is uneven, do not directly pave the all-ceramic tiles, you should ask the master to smooth the wall, and then pave the all-ceramic tiles, otherwise the all-porcelain tiles are easy to appear hollow after the paving.

Summary: The relevant content of how to stick the all-ceramic wall tiles firmly is introduced here for you, hoping to help friends in need. There are many problems that need to be paid attention to in the process of paving porcelain wall tiles, and it is recommended to ask professional construction personnel to pave them to ensure that the tiles achieve better paving effects.

In modern home life, everyone will paste tiles on the wall after decoration, and many friends will choose an all-ceramic wall tile when choosing tiles, but they don't know how to stick it firmly. The following is a brief introduction to the method for you, I hope it can help somewhat.

1. How to stick the all-ceramic wall tiles firmly.

1. First of all, before the leakage rolling, we should clean up the wall and wipe it with clean water to remove the dust and foreign matter on it, so that it can be more firm when pasting the wall tiles.

2. When pasting, you can spray water on the wall first to maintain the wetness, and then use an adhesive with a relatively high adhesion to apply it to the wall, and then paste the all-ceramic wall tiles on it, which will be firmer.

Second, how to choose tiles.

1. First of all, we need to consider whether the water absorption rate of the tile is very high, because the tile is easy to get dirty, so we will often clean it, and there will be water left on it when cleaning, if the water absorption rate of the tile is very high, it will expand and deform after absorbing water, which will affect the appearance, so we should choose the tile with low water absorption as much as possible.

2. Secondly, we also need to consider whether the tiles are consistent with the decoration style of the home. Some friends have a more gorgeous decoration style at home, so we can choose tiles with bright colors and more textures to stick on the wall; Some friends have a relatively simple decoration style at home, so we can directly paste white tiles on the wall.

3. When buying ceramic tiles, many merchants will recommend cheap tiles to us, but the quality of these tiles is often not very good, and various problems will occur after a period of use, and it is too late to regret it. Therefore, when buying, we should try to choose those brands of ceramic tiles with greater fame, after all, the greater the fame, the better its quality will generally be, which has been tested by the market.

Summary: The above is for you to introduce the content of how to stick the all-ceramic wall tiles, I hope it can help you. If you want to know more, please pay attention to Qeeka Home.

The first method, if the wall tile is all-porcelain, you can use a sander on the back to brush the hair, glue the copper wire with marble glue, and then paste it on the wall. The second method is to use the liquid acacia, if it is used in places such as film and television walls, you can make a layer of wooden bottom board on the wall and paste it with black structural glue, so that the structural glue is very strong after drying, and it is difficult to take it off. If you are afraid of getting out of shape, you can also use cement to polish the wall and directly glue it with structural adhesive.

The third method, such as outdoor door posts, etc., can be made of aluminum alloy or galvanized iron pipes into a shelf, and then pasted with marble glue and structural glue. The whole tile paste does not need to be soaked in water, and the ordinary surface brick is different, after soaking in water, it can not be buried, so it must not be soaked in water. The whole tile must be brushed with adhesive, and the glue on the tile should be placed for two hours to allow the adhesive to fully penetrate into the tile before it can be pasted.

There are two reasons, one is that the whole tile is heated and expanded, and there will be no seams, and the other reason is that the firing process of the whole tile is different from the ordinary process, and the firing time is long, and the whole tile will be slightly deformed, so the whole tile is not very smooth, and the seam can just make up for the uneven place.

The method of sticking the all-ceramic wall tiles is as follows: First of all, we should clean up the wall before pasting, and wipe it with clean water to remove the dust and foreign matter on it, so that it can be more firmly fixed when pasting the wall tiles. When applying the core of the front sock, you can spray water on the wall first to maintain the moisture, and then use an adhesive with a relatively high degree of adhesion.

We need to carry out a brushing treatment on the surface of the whole wall, and then we start to soak the purchased tiles with water, so that after the tiles have been soaked, we can greatly improve its water absorption rate by pasting the tiles on the wall, and the use of Qing Tangerine on the entire wall can ensure the perfect flatness and firm performance of our tiles.

How to make brushed material.

1. The first step is to mix the cement with the interface agent, stir them evenly, and then paint them on the wall. 2. Then we need to use a shovel blade and some special tools, borrow these tools to draw vertical strips on the wall, and then apply paint, the purpose of this is to make the wall rough, and then we use a latex paint painting roller to paint on the wall, so that there can be a brushing effect. If there is a special request, we can use special spraying and dismantling equipment for spraying, which can also make a good brushing effect.

Do you need sand and adhesive backing.

Generally, ordinary cement is mixed with an appropriate amount of lime paste or mixed with an appropriate amount of sand to serve Zen. Mortar, with a brown brush for small brushing or with an iron trowel for a large remaining skin brushing, method: first use cement lime mortar to lay the primer twice; Scrape another strip of plain cement.

Slurry; Brushing with cement-lime mortar. In addition to cement brushing, there is also paint brushing. Paint brushing is divided into gypsum brushing and oil brushing, which are mostly used for plastering in old dust rooms.

The decorative effect of brushing is good, but the work efficiency is low and it is easy to be polluted.

There is no need for a pro with adhesive backing.

The ratio of cement to interface agent.

You don't understand at all, dear.

You have to be according to the proportion of Qing slippery, I told you here that you don't understand, you can't use the wrong thing, if you tell the ant to bury these socks at all, I suggest you go to the ground to find a master to teach you on the spot.

Wall brushing needs to use cement sand and interface rock destroyer (108 glue), usually the ratio of cement and 108 glue is 6:4, if the cement strength is high, then according to the ratio of 5:5. However, if the Jiao's early water jujube is different, then the standard of proportioning is also different.

Can you pull the hair on the waterproof.

No. The brushing before waterproofing is not used for tile bonding, and the waterproof layer is the bonding surface. It is recommended to carry out brushing, because the frosting process used on the back of the tile is to increase the adhesion of the tile.

After the waterproofing has been completed, the waterproof layer has been formed, and after the brushing, the matte surface of the tile will be combined with the mortar to fill the gaps of the brushing, and the adhesion will be stronger. It is recommended that the all-ceramic tile waterproof adhesive mortar be mixed with waterproofing agent or use waterproof mortar!