The ADSL client device is automatically restarted

1.Troubleshoot the problem with the network cable or the problem of the crystal head contacting the connection2It may be a voltage problem that causes the broadband cat to restart and cause the connection to drop, find a multimeter to test the voltage to see if it is normal; 3.

Excluding the above two reasons, it may be caused by the incompatibility between the speed configuration of your computer network card and the Ethernet port of the up-connected device, you can try to change it as follows: right-click network neighbor Attribute Right-click local connection attribute General configuration Advanced connection speed and duplex mode, change the original "adaptive" to "10m full-duplex" can generally be solved.

This is a serious problem! Suggestion 1 blow up your computer, 2 take your Mercedes-Benz tractor and drive it to the field; Go inside,

Leave the dial-up task to the router to complete.

Wiring: the cat is connected to the router WAN port, and the computer is connected to the router LAN port;

The computer network card is set to automatically obtain the IP;

Log in to the router management page with a computer browser (generally, the username and password are admin, if not, please refer to the router manual);

Switch to the WAN port settings page, configure the WAN port to PPPoE dialing, enter the correct Internet user name and password, and save the restart route. The dialing method is set to auto-dial or auto-redial when disconnected.

As long as the power of the cat and router is turned on, the computer or other terminals can be connected to the Internet, and there is no need to dial on the terminal.

Buy a functional router, Xiaomi routers, and polar routers are all very good choices. The broadband account is built into the router, and as soon as the computer is turned on, it is very convenient to connect to the Internet directly through the router.

Buy a router, set the username and password inside, so that when you turn on the computer, you can go directly to the Internet, and the router is very cheap 80 yuan is much worse.

The setup of the router is very simple, and the manual can be understood at a glance.

If it is a normal ADSL, you cannot set a user password in it.

You're talking about adsl with routing

Auto-dialing relies on software to help, and only cats can't achieve it. You can go to the station of Telecom or Netcom to place their special dialing software, which can be set up to automatically dial when you turn on the phone.

In the case of XP system, find "broadband link" in the network link

Vista or Win7 find "Broadband Link" in the Open Network and Sharing Center

Then right-click on the broadband connection icon option and uncheck the "prompt name, password, certificate, etc.". Then pull the shortcut for the broadband connection into the startup section of the start menu.

In this way, the computer can be automatically dialed as soon as it is turned on.

1. Right-click Online Neighbor - Properties; 2. In the network connection window, right-click the broadband connection property 3, and then in the properties dialog box, click "Options" 4. Remove the check mark in front of the "prompt name, password and certificate, etc.", and click "OK" to exit 5. Drag the broadband connection icon on the desktop (press the left button to find the "start" behind the start menu, and then enter the username and secret correctly and then get the username and secret you applied for at the communication company.

If it is a problem with laptop wifi, please refer to the following.

The first step seems to be to set up a shared connection first, open the wifi connection, properties, advanced, enable the Internet sharing connection, the following is a local connection, the second step, and then connect the computer and the router with a network cable, note, the line that the router connects to the computer should be connected to the WAN port, and then you need to set the router's Internet access mode to dynamic Internet access, and then you can try, generally these two steps need to be completed separately, generally the second step is done first, and then the first step is done, otherwise, When you enable shared connection, the IP address of the local connection will be automatically specified, and you won't be able to connect to the router to set it up!

There may also be a question of conflict.

1. It means that another computer in the same LAN also uses this IP address, and the IP addresses of the two devices conflict, so you can manually set it to a different IP from other devices, if it is to automatically obtain the IP, restart the computer.

2. You can click the "Start" button, select "Command Prompt" in "Attachments", and enter "ipconfig renew" in the command line state to let the system release the current IP address and get a new one.

3. Error prompt similar to 00:20:ed:

9e:55:b6 is the MAC address of the other computer or network device.

If the IP is assigned by an administrator, you will need to contact the administrator to report the IP address conflict, request a change of IP address, or find the computer that caused the conflict to fix it.

If so, after logging in to the router, the ADSL client device interface appears.

The IPs of the cat and the router are both in conflict. Unplug the WAN cable of the router, restart the router, and then go to the settings.

It's not necessarily that the router is bad, you restore the router to factory settings and take a look, press and hold the reset hole with a toothpick or pin for more than 5 seconds when the power is on, wait until the computer is connected to the router, and then enter the settings.

It should be a problem of delay, call ** to customer service, and it is OK to say the situation.

The general ADSL client device only uses the basic bridging function, and by default it is a branch sock that does not need to be configured with data. However, if it cannot be used normally after replacement, it is necessary to check whether the original device is set with special data (such as whether the routing function of some cat scales is enabled) or whether the VPI and VCI match.

The IPs of the cat and the router are both in conflict. Unplug the WAN cable of the router, restart the router, and then go to the settings.

It's not necessarily that the router is bad, you restore the router to factory settings and take a look, press and hold the reset hole with a toothpick or needle for more than 5 seconds when the power is on, wait until the computer is connected to the router, and then enter the settings, and there are problems, I can QQ teach you, how many numbers do you have.

This is because both your router and the cat's gateway IP are 192 168 1 1 caused.

The simple solution is to turn off the cat first, then re-enter the router, and then turn on the cat after the settings are completed.

If you want to stop this problem in the future, then the computer is connected to the router separately, and the incoming route can be modified in the LAN port settings in the advanced settings to modify the gateway IP of the router.

For example, if you change it to 192 168 3 1, you need to log in to the router in the future, and you can use this new routing gateway.

If you don't pick up the cat first, just use the router to connect to the computer, and then connect the cat after the route is set.

There can be several problems: 1You may be attacked by ARP illegally, and someone will disconnect you with ARP control software such as a cyber law enforcement officer.

One can be connected to the Internet. 2.If you have problems with the system, you can use optimization software such as Super Rabbit to optimize your system, if it doesn't work, then you can only change the system and re-start a 3

The problem of the cat, it may be that the power supply voltage is insufficient, it may be that there is a problem with the cat itself. You can try it with a different cat. 4.

If the NIC is incompatible, the NIC driver may be incompatible, and a new NIC or NIC driver may be changed. Try them all, just these few questions, it's all my experience.

When there is no signal, the broadband connection is still disconnected, if it is the connection status, the act indicator is not still flashing, there is data transmission, the act light should be flashing, you are in this situation One may be the cat has a problem, and there may be a bad connection to the line, it is recommended to find another cat to test it, if you rule out the problem of the cat, call 10000 to find a telecom person to check the line.

I also had this problem in my dorm room, and I think the cats are inferior.

The best way is to find a friend to borrow a good ADSL equipment to try it, if it is really a problem with ADSL equipment, then buy a new one, it is not expensive