How to install the washing machine boom when it falls

Washing machine boom drop installation method: use a screwdriver.

Remove the screws and snap the boom into the side grooves.

Precautions for washing machine installation:

Power supply and grounding: In order to avoid unnecessary fire, electric shock or personal injury, all electrical wiring and grounding must be set in accordance with national electrical standards. It is the responsibility of the appliance owner to provide proper care for this appliance. Never make a wall outlet.

or an extension cord overloaded. Overloading may cause a disaster or lead to an electric shock.

Water**: The washing machine is filled with water at a working pressure of 50 800 kPa, which may result in water when the water pressure is lower than 50 kPa.

The valve fails, or the filling time is longer than the programmed control time, and the display appears 4e. Before using your washing machine, you should check all connections on the inlet valve and faucet to prevent water leaks.

Indoor floors: In order for your washing machine to perform at its best, your washing machine must be placed on hard, flat, clean ground free of water and grease. If the washing machine is installed on uneven or unclean ground, noise or vibration will occur.

In order to minimize vibrations or unbalanced loads, wood floors need to be further reinforced. carpets and soft floor tiles.

Surfaces can cause vibrations to occur during work as well as slight movements of the washing machine. Do not place your washing machine on a platform or on a structure with weak supports.

The washing machine barrel has four booms (one for each corner), each boom has a hook, you hook it on OK, if the place where the hook is fixed is broken, it will be welded.

The sequence of changing the boom of the washing machine 1 Remove the four screws connected to the box on the upper frame of the washing machine 2 At this time, you can see the boom of the four hanging washing buckets, and replace the boom that needs to be replaced, it is very simple, it is four directly hung on the top of the box, and you can take it down by hand without any tools. I often disassemble prototypes.

Summary. The rope on the washing machine spin dry barrel has fallen off, hanging**?

Hello dear ? The brake line, which is hung on the lid of the spin-off barrel and the brake disc next to the motor, is hung below.

That rope is connected to the safety switch. There is a metal hook at the bottom of the top lid of your washing machine, which can be hung directly on it.

Its function is safety, that is, when it is spin dry, if you don't cover it, it won't run. The lid of the washing machine must be closed so that the washing machine will dry later. So this is called a kill switch.

Hope mine is helpful to you, thank you and have a great day!

The rope on the washing machine spin dry barrel has fallen off, hanging**?

The rope on the washing machine has fallen off, and the mu is hanging**? Hello dear ? The brake line, which is hung on the lid of the spin-off barrel and the brake disc next to the motor, is hung below.

The rope was dismantled and connected to the safety switch. There is a metal hook at the bottom of the top lid of your washing machine, which can be hung directly on it. Its function is safety, that is, when it is dried, if you don't cover it, it won't be ambushed.

The lid of the washing machine must be closed so that the washing machine will dry later. So this is called a kill switch. Hope mine is helpful to you, thank you and have a great day!

Hello dear, brake cable, the top hangs on the lid of the spin bucket, and the bottom hangs on the brake disc next to the motor. That rope is connected to the safety switch. There is a metal hook at the bottom of the top lid of your washing machine, which can be hung directly on it.

Its function is safety, that is, when it is spinning, if you don't cover the cover code late, it will not run. The lid of the washing machine must be covered, and the washing machine will be dried in the future. So this land god is called a kill switch.

After the washing machine replaces the boom, it still hits the wall, and the specific reasons and treatment methods are:

1. There is debris between the dehydration bucket and the washing bucket. Just remove the clutter.

2. The balance ring of the dehydration bucket is ruptured or leaking, so that the balance of the dehydration bucket is lost when it rotates. Just replace the balance ring and it will solve the problem.

3. The flange of the dewatering bucket.

Loose or cracked fastening screws. Just tighten or replace the flange.

4. The dehydrated bearing is seriously worn or loose. Simply tighten or replace the dewatered bearings. Infiltration Brigade.

5. The elasticity of the boom is uneven.

6. The clutch spring needs to be replaced to tighten the belt.

Precautions for daily use of washing machines:

1. Before washing, you should carefully check the label on the clothes to see if they can be washed, ironed, etc., and choose the corresponding washing program according to the texture of the clothes, such as cotton, chemical fiber, wool, etc.

2. After the washing machine is used up, it is best to open the glass window of the washing machine a little, so that the sealing ring can be extended.

service life, and is conducive to moisture dissipation in the start-up.

3. When using hot water for washing, do not use more than 50 hot water from the cong stool, and pay attention to the fact that the water can not splash the control board, so as to avoid the internal electrical parts.

Burn due to water contamination.

Remove the wave wheel and see if there is a zipper pull, if not, it may be flushed into the drain. There is a small cap in the middle of the wheel, and you can pick it up and you can get a snail.

When washing clothes in the washing machine, if you don't close the zipper, you will often hear the sound of the zipper hitting the washing machine, which will not only shorten the life of the zipper, but also damage the inner wall of the washing machine.

Use pliers to clamp the upper stop, let the upper stop open his mouth slightly, he will fall off the cloth belt, take off the old slider, replace the new slider, and then put the top stop in the original position, tighten it with pliers, clamp it hard or lay this part flat, knock it a few times with a small hammer, remember not to knock on the teeth, let it be firmly fixed on the cloth tape.

It should have fallen into the washing machine, you take off the wave wheel, and then see if there is a zipper pull, if not, it may be washed into the drain pipe by water. There is a small cap in the middle of the wheel, and you can pick it up and you can get a snail.

Summary. The inner cylinder of a fully automatic washing machine is crooked, which will affect the work. The inner drum of the fully automatic washing machine is suspended by 4 booms.

If the inner barrel is crooked, it means that the springs of the 4 inner barrel booms are loose and broken, so there is no way to balance the inner cylinder. It is necessary to replace the boom with a new one, otherwise it will hit the barrel if it is used like this, and the washing machine with an improper inner cylinder will be easily damaged by long-term use.

The 4 booms of the automatic washing machine are not broken, the barrel is off, how to get it.

The inner cylinder of a fully automatic washing machine is crooked, which will affect the work. The inner drum of the fully automatic washing machine is hung by 4 booms. If there is a crooked inner cylinder, it means that the springs of the 4 inner barrel booms are loose and broken, so there is no mega cover method to balance the inner cylinder.

It is necessary to replace the boom with a new one, otherwise it will hit the barrel if it is used like this, and the washing machine with an improper inner cylinder will be easily damaged by long-term use.

If it is a fully automatic washing machine (with a wave wheel and a laundry bucket), you need to open the upper cover of the washing machine (or observe the bottom), remove the screws around the upper cover of the washing machine and open the upper cover, and there are four levers around the four corners to see which one is falling off, or whether the shock spring (or shock absorbing airbag) is damaged and falling off, reinstall or replace the above pull rod, and install the upper cover (note that the plug should be pulled out when removing the upper cover, and be careful not to pull out the signal line and electric weak source line hard). If it's a drum washing machine (only a bucket, no middle wave wheel), then you still don't move, just send it for repair, because even if you have one, you won't be able to install one piece after dismantling.

1. Fold and unload the entire workbench above, there should be 2 or 4 screws, unscrew, as shown in the figure below.

2. How to disassemble the washing machine barrel Some washing machine screws may be in the back, you can lift the front to tilt it or find someone to hold it as shown in the figure below.

3. How to disassemble the washing machine barrel is mainly not to damage the power cord in the back, and push it forward slightly after loosening the screw, and the panel can be taken out.

4. How to disassemble the washing machine barrel with a large flathead screwdriver, unscrew the screws, take out the wave wheel, there is a gasket under the wave wheel, don't lose it.

5. Disassemble and disassemble a large nut for the washing machine barrel, it is recommended to find a special tool and tighten it when installing it back, as shown in the figure below.

6. There is an L-shaped fixed plate with a cross-section under the washing machine barrel, and the whole barrel can be taken out after being removed as shown in the figure below.

What you are talking about is a semi-automatic washing machine, first unplug the power plug, open the back cover of the washing machine, gently turn the dryer barrel, there is a link flange between the motor and the drying bucket, there is a fixing screw (also called the top wire), after loosening the screw, the motor and the drying bucket will be separated, and the drying bucket will be removed by gently lifting it upwards. If you don't have a little knowledge of this, it's better to ask a master, so that the deaf don't become dumb.