How to remove the screen of a computer monitor

How to remove the screen of your computer monitor Steps:

1.Place the monitor in reverse on the table and remove the base screws.

2.Remove the base.

3.Turn the display upside down and remove the bezel.

4.Then turn the monitor upside down and remove the back frame.

5.Remove the rear case containing the motherboard and power strip.

6.It is enough to replace it after judging which one is faulty during maintenance. Remove the screws to remove the power supply or motherboard. The split step ends.

Accessories required for laptop screen modification monitor:

1. LCD screen.

2. A power board that matches the LCD screen backlight tube interface.

5. a button board.

6. Display shell nesting.

Connect the power board and the backlight tube, and weld the power supply connection between the power supply and the ** board. Connect the connection between the key switch and the board, and connect the screen cable between the LCD screen and the board. It can be powered on and tested.

Extended Information: A display is also commonly referred to as a monitor. A monitor is an IO device that belongs to a computer, i.e., an input and output device.

It is a display tool that displays a certain electronic file on the screen through a specific transmission device and then reflects it to the human eye. It can be divided into various types such as CRT, LCD, etc.

In general, liquid crystal displays.

It consists of the following parts:

1. LCD module.

Glass substrate: Inside are liquid crystals and grid-like printed circuits. Timing control:

It is used to generate the timing and voltage that controls the sequence of the deflection of liquid crystal molecules. Lamp: Produces a white light source.

Backlight: Reflects the light produced by the lamp onto the LCD screen.

2. a control panel.

The control board plays the role of signal conversion. Converts signals from various input formats into signals with fixed output formats. For example, the input signal to the screen of 1024 x768 can be 768, etc., and finally converted into the output format 1024 768.

3. Inverter.

High pressure is generated and is used to light the tube.

Nowadays, LCD monitors are getting easier and easier to dismantle. The cover can be removed directly by hand, and there is no need to remove it with a screwdriver. The following describes how to disassemble the LCD monitor.

Method steps.

1 8 step by step reading.

Put the LCD display flat, then hold the outer frame of the LCD with both hands, and press it up hard to loosen it.

After the buckle is opened, then buckle another corner, buckle loosely, don't worry, the strength is moderate.

Then pull the buckle loose.

Yanbian buckled all the way and pulled all the buckles apart.

Remove the frame. You can see the control panel of the LCD display.

See 1 image remaining.

To disassemble the parts inside the LCD monitor, you only need to remove the screws you see to disassemble them.

Pay attention when installing the panel. Keep your hands on the keys. Press down again.

Then put the edges around you right, and then press them tightly with your hands.

Precautions. If you find this experience useful to you, please click "Thumbs Up" or "Vote for TA" or "Follow TA" on the top right corner of the page to give me a support. If you are afraid that you will not find this experience next time, please click [Pentagram] on the upper right corner of the page to collect this experience.

Like and share. Read more

Find a professional to dismantle it.

The method and detailed operation steps of making a monitor are as follows:

1. In the first step, remove the LCD screen of the old notebook for use, as shown in the figure below, and then move on to the next step.

2. Secondly, after completing the above steps, assemble the TV components purchased from online (5-in-1 driver board + remote control + high-voltage strip + screen cable + speaker), as shown in the figure below, and then enter the next step.

3. Then, after completing the above steps, keep the shielded cable and high-voltage strip interface, see the following figure for the shielded cable and high-voltage strip wiring, and then enter the next step.

4. Then, after completing the above steps, install the fixed screen on the display case, install the front cover, install the base, and fix it with bolts, as shown in the figure below, and then enter the next step.

5. Finally, after completing the above steps, it is modified, as shown in the figure below. In this way, the problem is solved.

The laptop monitor is linked to the host computer. So it will be more troublesome to disassemble the display, what should I do? Here's how I can disassemble a laptop monitor, and you're welcome to read it.

Then carefully break open a little bit of the plastic case of the notebook, insert a hard card, and then carefully and gradually open the bayonet of the plastic case of the notebook screen.

Remove the front cover after the bayonet is opened. Then unscrew the set screws at the four corners to remove the back cover.

After the back cover is removed, the screen looks like the picture, you can see that there are also fixing screws on the side, you don't have to rush to remove them. First remove the cable of the link. The cable is fixed with adhesive tape, first tear off the tape (be careful), and then pull the cable down.

1. Put the LCD display flat, then buckle the outer frame of the LCD with both hands, and press it up and loose. 2. After the buckle is opened, then buckle another corner, buckle loosely, don't worry, the strength is moderate. 3. Pull the loose buckle apart.

4. Extend the side all the way and pull the buckle open. 5. Remove the frame. You can see the control panel of the LCD display.

6. To disassemble the parts inside the LCD monitor, you only need to remove the screws you see to disassemble it. 7. Pay attention when installing the panel. Keep your hands on the keys.

Press down again. 8Then put the edges around you right, and then press them tightly with your hands.

Different monitors, installation and disassembly are different, but the basic steps are the same, as long as you study carefully, you can disassemble and install.

1. Tool preparation: a Phillips screwdriver.

2. Disassemble the LCD display.

1. Clean up the desktop, pad the desktop with a soft cloth, and buckle the LCD screen of the monitor downwards on the desktop. Be sure to pay attention to the clean desktop and not have any clutter, otherwise the screen will be crushed and the loss will be heavy.

2. Unscrew the fixing screws at the four corners of the back cover of the monitor, some monitors need to disassemble the base first, and operate according to the actual situation.

3. When removing the back cover, pay attention to the position of the audio input lotus plug of the two left and right channels marked with red arrows in the figure below.

4. The following picture is the internal structure of the LCD display with the back cover open. The internal structure of different displays is not exactly the same.

5. The metal shield in the above figure is to prevent the wheel from taking holes to prevent external electromagnetic interference from damaging the normal operation of the internal circuit. Two of the multi-turn circular holes are heat dissipation holes. Unscrew the two fixing screws on the bottom of the shield, slide down the shield, and then lift the shield upwards to remove.

In this way, the LCD display is disassembled. Reverse operation can be used to mount the monitor.

If you need to disassemble your computer monitor, we recommend that you follow these steps:

1.Disconnect the computer monitor from the power supply, and then place the computer display on a stable surface.

2.Use a flat tool, such as a screwdriver or plastic card, to gently insert it into the gap between the monitor bezel and the backplate, and then gently twist the tool to separate the bezel from the backplate.

3.Once the bezel and backplane are separated, you can see the electronics and wiring inside the display.

4.When disassembling the monitor, it is important to exercise caution before proceeding to avoid damaging the electronic components and wiring. If you're not sure if you're doing it correctly, it's best to have a professional disassemble it.

When disassembling a computer monitor, follow these steps:

Turn off the power: First, make sure your computer monitor is turned off and disconnect the power plug to avoid the risk of electric shock.

Remove the stand: If you're using a stand that adjusts the height and angle, first remove the stand from the monitor. Usually, there are screws or clips at the bottom of the bracket, and you can loosen them using a screwdriver or an appropriate tool. Then, gently detach the stand from the monitor.

Removing the bezel: Depending on the model of the monitor you are missing, the bezel may have set screws or clips. Use the appropriate tools, such as screwdrivers or plastic tools, to easily open the bezel fixings.

Disconnect the cables: Once the bezels are removed, you can see that there are various cables behind the monitor, such as power cables, ** cables, and data cables. Please disconnect these cables carefully. Usually, they will have a fixed plug or need to be pulled out by pressing the release clasp.

Please note that different models of computer monitors may have different disassembly methods and details. Therefore, it is best to refer to the monitor's user manual or contact the monitor manufacturer for detailed removal instructions. If you are unsure or unfamiliar with dismantling on your own, consider seeking a professional repair service or consulting a technician for assistance.

Do you know how to disassemble a computer monitor, the following is what I brought about how to disassemble a desktop computer monitor, welcome to read!

How do I disassemble a desktop computer monitor?

Turn off the monitor, disconnect the power, and unplug it. This is the most important step and one that keeps the whole process safe.

Unscrew the VGA connector screws connecting the monitor and host on the back of the case, and gently unplug the VGA cable.

Unplug the power cord from the back of the monitor. Unplug the VGA cable in the same way as in the second step.

Move the monitor to a flat, soft, wide location, such as a table, sofa. And perform an upside down, ready to disassemble the base.

Unscrew the base screws in a counterclockwise direction, and then slowly lift the base up to complete the disassembly.

Hold both sides of the bracket and pull it out with a slight shake to remove the bracket.

After the disassembly is completed, the parts are evenly squared, and if you need to pack, put them into a special carton.

1.How to convert a note monitor into a desktop monitor.

2.How to take apart the computer monitor.

3.How to disassemble the HP monitor.

4.How to disassemble the desktop computer CPU.

5.How to disassemble an LG computer monitor.

6.How to disassemble the base of a Dell computer monitor.

7.How to disassemble the base of Lenovo computer monitor.

8.How to disassemble the HP LCD monitor.

9.How to remove the desktop graphics card.

10.How to remove the desktop integrated graphics card.

Some netizens asked, for this problem is actually very simple, let me briefly introduce the disassembly method of the notebook display for you! Hope it helps!

How to disassemble the laptop monitor:The first step is to have tools such as screwdrivers ready.

The second step is to remove the battery.

The third step is to remove the bezel of the screen.

Step 4: Unscrew the screws on the screen frame.

Fifth, remember to pull out the screen cable first when you take the screen down.

The sixth step,Tear the tape on the socket first,Don't tear the seventh step,Okay,Now you can see the complete screen of Yuntong。

Step 8, after removing it, you can write down the model of your screen Step 9, remember to put the buckle on the shell quietly when you install it back.