What should I pay attention to when installing smart door locks?

It is recommended that you call the service on the smart lock package**, and the big brand smart locks have national service**.

1. If the door is not keyed in advance, the door needs to be opened, and the opening line must be drawn according to the opening drawing provided by the factory, including the front, back and side of the door.

2. Open the front, back and side holes according to the drawn hole line. The precautions for opening the door are as follows: open the front hole to prevent the wood fiber from flashing, and first use a cutter to cut the fiber along the opening line to avoid the opening being too large; When opening the side hole, pay attention to prevent fiber flash, prevent the hole from being too large and rough, take the lock cylinder as the benchmark, install the lock cylinder and check it, if it is not suitable, you can make corresponding adjustments; When opening the door frame and door hole, the requirements are high to prevent the shaking of the door lock due to the false position.

Note that the standard smart lock lock body must be installed, because the original lock body of the entrance door has a long service time and unstable quality, and the degree of cooperation with the smart lock is uneven, which affects the normal operation and good experience of the smart lock.

When installing the lock body of the smart door lock, it should be noted that the screw tightening must be in place, and there should be no gap between the lock body and the door. After the lock body is installed in the door body, it is necessary to observe whether the lock body is parallel, can not offset left and right, and also observe whether the lock body lining plate is in place with the slot of the door, and there can be no high and low on one side.

3. The position of the gusset hole and the position of the deadbolt must correspond, if the correspondence is not good, the door will be loose or cannot be closed, and the tongue can not be stuck into the gusset hole.

4. When installing the rear panel, the anti-locking knob should be hit straight up and down, and then buckled up, and remember that the anti-locking knob should not be horizontal. The connection of the wires must be made to be correct and secure, otherwise the door lock will not work properly.

5. The battery cover needs to be installed to prevent the battery from shifting and powering off when the door is closed and colliding, and the mechanical key needs to be brought at this time.

6. For the door that needs to be installed with the heaven and earth hook, install the lock cylinder after the lock body is installed in the door body, and use the mechanical key to test whether the opening is smooth.

7. After the installation of the smart door lock is completed, it is necessary to check whether the lock body is vertical to the door frame, there is no tilt, there is no loosening phenomenon after the door is closed, the handle rotates flexibly, the reset is normal, the lock tongue pops up normally without jamming, and the door can be closed with light force.

Smart door locks are indeed very convenient, fingerprint and password unlocking technology has been very stable, basically can be used with confidence, a fingerprint or a set of passwords can open the door, saving us the trouble of bringing keys and finding keys. Hope it can help you and have a happy life!

Introduction to the structure of the lock body.

First of all, let's understand the structure of the lock body to facilitate subsequent installation.

Lock body split diagram.

Installation. The lock body is connected with the heaven and earth rod on the stainless steel door, and then the lock body is fixed on the door panel with screws.

First, screw the 2 fixing posts on the front panel, connect the power cord, insert the square shaft, and lock the front panel with the fixing screws through the positioning shrapnel, and align the screws to tighten the rear panel fixing block.

Connect the rear panel, insert the square shaft to fix the rear panel with set screws, tighten the set screws, and close the battery cover.

Install the door buckle box on the door frame, install the door buckle plate, fix the buckle screws, and finally check whether the lock body moves smoothly. The wooden door uses a special door gusset plate for wooden doors, which is fixed with self-tapping screws, and the stainless steel door uses a special door gusset plate for stainless steel doors, which is fixed with metric screws.

Inspection. Instructions:

Whether the lock is powered on. Whether the inner and outer handles can be lifted to lock the door. Press the fingerprint flip cover, enter the test fingerprint, turn the outer handle and press down to see if the door can be opened.

Precautions for use.

1. When adding fingerprints or opening the door, the fingers must be kept clean and please put the fingers in the middle of the fingerprint collector closely, if the position of the fingers placed in the collector is deviated, it will cause the operation to be unsuccessful or the quality of the collected fingerprint image will be reduced, and then cause the unlocking failure.

2. When this product is in the factory (no fingerprint entry) state, any reasonable finger can open the door, and it will be automatically locked after 5 seconds; This function will automatically fail after adding a fingerprint, and only a valid fingerprint can be unlocked, so a fingerprint must be entered after installing this product.

3. When entering fingerprints, enter them according to the voice prompts, and the time for pressing your fingers on the collector should not be too long, about seconds. If it is left for too long, it will affect the collection effect.

4. The smart lock will be dormant when it is not working. When a finger is pressed, the light of the fingerprint scanner will be lit, so do not remove your finger until you hear a voice prompt. If you remove your finger before the voice prompt, it will be considered an illegal fingerprint.

Note: If the illegal fingerprint is operated 5 times in a row, the fingerprint head will be frozen with a voice prompt "The fingerprint lock is frozen, please wait", pull out the battery or return to normal work after one minute. ）

5. The normal working voltage of this product is in.

Note: If there is a voice prompt of "low battery, please replace the battery", the system will enter the power-saving mode, in this mode, this product can only be unlocked, and cannot be added, deleted fingerprint, restored to default, and volume switching. It is necessary to replace the new battery as soon as possible, avoid mixing the old and new batteries when replacing the battery, and pay attention to the correct installation of the positive and negative polarity when putting on the battery.

What should I pay attention to when installing a smart lock? Some friends choose to install their own after buying smart locks, in fact, there are many details that need to be paid attention to in the installation of smart locks, and the following will tell you what problems to pay attention to when installing smart locks.

1.When installing a smart lock, pay attention to the way the lock body opens the door.

In the process of installing the lock body, it is divided into inner opening, outer opening, left opening and right opening. This is adjustable on the lock body, and the specific adjustment method can be found on the lock body, and there are two trigger buttons to adjust the lock tongue of the lock body.

2.Pay attention to the fixing screws when installing smart locks.

In the actual installation, the accessories package contains 4 screw fixing posts and 2 long fixing screws, often customers ask whether the matching screws are missing two, 4 screw fixing columns There are two thick and two thin, the thick fixing column is placed on the top and bottom of the lock, and the thin fixing column is to fix the lock body. No screws are required. The reason is that the lock body is knocked back and forth too many times during use, which will loosen.

If it is not fixed with fixing screws, it will affect the user experience after loosening.

3.Pay attention to the adjustment of the handle when installing the smart lock.

The door lock handle is adjusted by using a wrench out of the reset module, and there is no need to twist the screws at the large square steel. If the handle is replaced by twisting the gear answering screw, there will be a problem that the deadbolt in the hand of Xing Shenhui on the front panel will come out, but after verifying the fingerprint password, the lock cannot be unlocked.

Heart of Kings 2 click to play

The precautions for smart lock installation are as follows:

1. Confirm the door and the old and new, type, thickness, whether it is with the heaven and earth rod, open the door, etc., to determine whether the door is suitable for using fingerprint locks.

2. Disassemble the package and check the fingerprint lock accessories: There is a list of the number of components in the fingerprint lock manual, the front and rear panels, lock body locks, buckle boxes and other large components such as gusset plates are convenient to check, but don't forget that the front and rear straws, square rod springs, countersunk screws, semi-countersunk screws and other small accessories are complete.

3. Disassemble the old lock: After the accessories are ready, the middle book door opening and other conditions are ready, and the old lock can be removed for installation. When disassembling the old lock, care must be taken to keep the parts and functions of the old lock as complete as possible to prevent unexpected accidents during the installation of the fingerprint lock, and the old lock can be replaced with a spare.

4. Install fingerprint lock: Take the moli fingerprint lock in the installation steps as an example, mainly the installation with lock cylinder and the installation of the front and rear panels.

5. Check if the handle and deadbolt are working properly. Check that the keyhole of the door frame fits.

6. Power-on debugging: install the fingerprint lock and debug the mechanical components, and set up and debug the fingerprint lock electronic module. First, initialize the new fingerprint lock and clear the original data.

Enter the fingerprint, password and proximity card for the overall test to see if the overall electromechanical operation of the fingerprint lock is normal. Chapeto.

7. Explain the basic guide of fingerprint lock operation: at this time, all the installation and testing steps are completed, and the fingerprint lock can be used normally; The installer will generally tell the user some precautions for the use of the fingerprint lock, and help the user to be familiar with the use of the fingerprint lock, such as helping the user to enter the fingerprint, etc.

Are smart door locks safe? What are the installation precautions? What brand is better?

First: The password fingerprint lock used in the home is relatively safe. The ordinary door lock handle opening method cannot guarantee sufficient safety performance.

It is easy to open the door by drilling a small hole from the outside of the door and turning the handle with a wire. Password fingerprint locks are different. Patented technology with the addition of a safety handle button to the indoor handle setting.

Second: Some doors may not fit the smart lock you want to order and install. At this time, the guru usually recommends changing it.

It should be noted that the modification of the smart lock involves a change in the door hole, and the installer can make a simple change for free. In the event of a major change, there may be costs involved, which will be borne by the installer: the installer has the right to refuse to install the lock on the dedicated door.

So, before placing an order, be sure to ask if your door is suitable for installing a smart lock. In fact, in general, security doors are OK.

Third: Smart locks cannot be installed on all car doors. The installation of some special doors (such as panel doors, royal doors, hidden lock bodies, etc.) needs to be changed.

In addition, the installer has the right to refuse the installation if the changes are significant. In addition, these doors require the replacement of the Heaven and Earth Hook, which may make the Heaven and Earth Hook unusable, so please consider carefully. In general, everyone will make the same change and remove the heaven and earth linkage.

There are a few caveats for installing the heaven and earth hook behind this.

Processor upgrades. The inner handle of the door is designed with a quick escape switch sensor for faster unlocking. The high-end 9000 series has an upgraded appearance, and its basic functions are almost the same as those of the DDL702.

In the field of foreign high-end fingerprint locks, it is the choice with the most abundant intelligent functions and a very good user experience.

To sum up, you must make preparations before installing smart door locks.

Nowadays, many home decorations will choose smart door locks, which are relatively safe, and we must pay attention to the correct process when installing. There are a lot of good brands out there.

It is indeed safe, you must pay attention to the choice of style when installing, you need to pay attention to the safety factor of the door lock, as long as it is a big brand, there is no big problem.

Its safety performance is a top priority for our consumers. At present, there are three main levels of smart door lock cylinders on the market. Its safety performance is from weak to strong.

It is recommended that you first choose a C-class lock cylinder with better safety performance. At the same time, the lock body material of the smart door lock is also worth paying attention to. Users can choose lock body materials with good corrosion resistance and high hardness.

Considering the brand of smart door locks and our users, it is recommended that you choose mainstream brand products, relatively speaking, the product quality and after-sales service of big brands are guaranteed.

For smart door locks, installation and after-sales warranty issues are very important, and at the same time, it is necessary to choose qualified products from regular channels, and do not choose three-no products because of factors such as **. Smart locks generally have fingerprint unlocking, password unlocking, Bluetooth unlocking, and key unlocking. In addition, some smart door locks also have unlocking methods such as swipe card unlocking, temporary authorization password, etc.

1 The environment, conditions and requirements of use. The advantages and disadvantages of the use environment, such as dry and humidity, door structure, thickness, left or right door, inner or outer door, in case you buy the wrong product.

2 The place used and its importance. That is, consider using it on street gates, hall doors, rooms, bathrooms, or passageways to choose a smart lock product that suits the desired function.

3 Consider the harmony with the decorated environment. According to your own preferences, when buying lock products, you should consider the coordination and matching of your living room.

1. Before installing smart locks, people should first see if their doors are suitable for installation. Generally speaking, wooden doors, copper doors, steel and wood doors, anti-theft doors, etc. are suitable for installing smart locks. However, for the sake of insurance, it is best for people to consult customer service when buying smart locks, which type of smart lock is suitable for their door, so that they are not afraid that the smart lock they bought back is not suitable.

2. The installation of smart locks depends on whether your door is open inward, or outward, or right or left. The way to open the door is different, so the way the fingerprint lock is installed will also be different.

3. The thickness of the door directly affects the installation of fingerprint locks. Generally speaking, if the thickness of the door is between the inside, a fingerprint lock can be installed. If it is lower than this mausoleum or changed to a thickness, or higher than this thickness, it is not recommended that people install fingerprint locks.

Even if it's installed, it's either unusable or your door will be scrapped.

Generally speaking, there are 4 thick or thin screw fixing columns, as well as 2 long fixing screws, the thick screw fixing column is placed on the top and bottom of the lock, and the thin one is used to fix the lock body. If the screws are missing, be sure to ask the merchant to reissue them, so as not to cause the fingerprint lock to be installed insecurely because the screws are not suitable.

5. People should fix the lock body in the process of installing the fingerprint lock, and it is best to calibrate the fingerprint lock twice before fixing, and at the same time ensure that the deadbolt of the fingerprint lock can be aligned with the original door frame, and the door lock installation must be positive and cannot be tilted.

6. After the fingerprint lock is installed, it should be tested whether it can be used normally. If people are struggling or difficult to close the door, don't force it to close it, it will break your door. This situation may be that the gap between the door leaf and the door frame is unreasonable, and people should adjust and correct it.

7. The installation of smart locks seems simple, but it is actually difficult, and people will make their doors full of holes if they are not careful, or mess up their fingerprint locks.