What s the matter with the Jetta high beam not bright, the old Jetta dashboard light is not on Hello

Hello, if the high beam on both sides is not bright, generally it is a fuse, switch, or a circuit problem, check whether there is electricity to the high beam fuse, if there is no control switch or line problem, if there is, it is a line problem between the fuse and the bulb!

Hello, in this case you need to see if there is a difference between the two sides of the high beam, if both high beams are not on, it may be that the fuse is burned out, if only one side is not lit, basically the bulb is burned out.

Hello, if the headlight high beam is not lit on both sides, first check whether the bulb is damaged, check the fuse and switch if the bulb is normal, if the light brightness is not enough, you can replace the LED bulb or install xenon headlights.

Hello, the high beam of the vehicle is not on, first you need to check if there is a problem with the bulb, if you are sure that there is no problem with the headlight bulb, you need to check whether there is a problem with the fuse of the high beam!

Hello, the high beam does not light up is either a relay problem, or a bulb problem, or a wiring problem, it is recommended to collect the simplest bulb first, go to the 4S store to check.

Hello, the brightness of the high beams of this Jetta car is enough to meet the use, if it is not lit then check whether the bulb is normal.

Hello, do you think the high beams are not bright enough, or the high beams are not on at all, if they are not lit, it may be a problem with the line.

Hello, if the brightness is not enough, you can modify the LED bulb, if the bulb is not lit, it may be the bulb burned or the wiring problem.

For this case, if the bulb is not damaged. It is possible that there is a fault in the line, so it is recommended to check it.

Hello, if the high beam is not lit, is the bulb broken, if not to check the fuse and wiring is not a problem!

In the case of high beams, you need to check it, and the focus is to check the bulb itself, is there a problem? Another is to check the light switch, and there may be a problem with the light relay, check it from these aspects.

Hello, the effect of the headlights of this Jetta is still okay, but if you often run at night, you can replace the xenon headlights or LED headlights.

Hello, this is recommended to check the high beam bulb or wiring, relay and other faults, go to a professional store to check it.

If the light brightness of the halogen headlights of the original car is average, the bulb is no problem, and you can only consider modifying the hernia headlights or LED headlights, and the brightness is better.

Hello! The high beams of this car are like this from the factory. If you feel that the brightness is not enough, you can modify it later!

Hello, if you need to modify the lighting in this situation, you can modify the xenon lamp, and the cost is estimated to be about 1500.

If a single bulb does not light up, it may be that the bulb is broken, if it is not lit, it should be a problem with the fuse or switch.

If the Jetta high beam is not bright, you need to check the bulb first, and the bulb is okay and you need to check the switch and circuit.

If this is the case for you, it is recommended to focus on checking whether the bulb is damaged and the dimming switch. and line connections.

Hello, if the bulb is not lit, it may be that the bulb is burned out. If the brightness is not enough, just change the L E D headlights.

Hello, in this case, it may be that the bulb is damaged, or it is the relevant fuse, you can check it.

Hello, first of all, check if the insurance is broken. Check again for bulbs and faulty wiring.

Hello, this one first check if the bulb is burned out, and then whether there is a problem with the fuse and relay.

In your case, the high beam bulb is broken or there is a problem with the wiring, and it is recommended that you go to a local professional repair shop to check it.

In your case, you need to check the car's light bulbs and whether there is a problem with the wiring.

Hello car dashboard.

The main reasons why the lights do not turn on are as follows:

1. The dashboard lighting is damaged;

2. The power supply wire of the dashboard is disconnected;

3. The power supply fuse of the dashboard.

Fusing; The problem can be solved by mainly examining the above aspects. First of all, check the power supply fuse of the dashboard, if it is blown can be replaced; Disassemble the instrument panel, the lights are generally at the back of the dashboard, and replace the lights that are not on. Generally, if the individual lights do not turn on, it means that there is no problem with the fuse and wire.

Hello, there are two situations when the old Jetta dashboard light does not light up, one is that the fuse is burned, and the other is that the small bulb in the dashboard is burned, it is recommended to go to the repair shop to find a master to check it, first look at the fuse, if the insurance is good, directly remove the dashboard and replace the small bulb inside to solve the problem.

The old headlight switch has a dimmer switch that can be adjusted, and the brightness of the three instrument lights and the air conditioning panel are adjusted by this switch.

The dashboard light of the old street is not lit, and it is normal that there is a problem with the power supply insurance of the dashboard. Causing his betrayal to be lit up.

The button on the side of the dashboard brightness steering wheel can be adjusted, I hope it will help you, thank you!

The 2013 Jetta low beam is not on. There is no light bulb when the power goes out.

Damage fuses.

Blowing off most of the low beams, fuses on the left side of the engine compartment fuse and/or instrument panel, the low beam adjustment circuit has a faulty problem, it may be a problem with the light adjustment switch. Check whether the lamp port assembly is broken, causing the low beam light to not light up. The headlight assembly needs to be replaced.

Generally speaking, the fifth situation does not occur often, and the cost of other conditions is relatively not very high, but it is important to go to the repair station to investigate first, and then decide what way to repair after determining the problem.

Reasons why the low beam does not light up:

1. The battery is dead. You can press the horn at this time to keep the battery power, if you forget to turn off the electrical appliances and don't work overnight, the next morning then you won't be able to drive, and even the low beam can't be turned on;

2. Brother Lamp and Bubble Damage. Most bulbs also have a certain life cycle, and the light intensity is close to being scrapped.

did not meet the standard, and at the same time Li ruined fever.

Strict until the filament is burned. In addition, there are some reasons, such as the headlight assembly is easy to enter the water after the vehicle wades, and the temperature drops sharply after the heated bulb hits the water droplets, so there will be rupture and damage, which will affect the lack of light;

3. The fuse is blown out, most of the low beam fuses can be found in the engine compartment fuse box or the fuse box on the left side of the dashboard, and the fuse is explained behind the fuse box cover, and a special clip is used to take out the detection.

If the instrument indicator is not lit, first check the power supply fuse of the dashboard, and replace it if it is blown. Disassemble the dashboard, the lights are generally at the back of the dashboard, replace the lights that are not lit, and generally the individual lights are not lit to indicate that there is no problem with the fuse and wire, the main reasons are as follows

1. The lamp of the dashboard is damaged and needs to be replaced in time;

2. If the power supply line of the dashboard is broken, there is an open circuit or short circuit, which will also cause the car dashboard to not light up;

3. If the power supply fuse of the car dashboard is broken, there will naturally be no power supply, and the dashboard will not light up.

Precautions in the use of the car dashboard:

1. When the indicator light is on, the odometer should be observed immediately, if the cumulative mileage reaches or exceeds l00,000km, the timing toothed belt must be replaced, otherwise the timing toothed belt may break, so that the engine can not work normally.

2. After replacing the new timing toothed belt, it is necessary to open the rubber plug outside the reset switch on the mileage dial, and press the reset switch inside with a small round bar to extinguish the indicator light of the timing toothed belt.

3. After replacing the new timing toothed belt, remove the odometer and adjust all the readings on the odometer to the 0 position.

Hello, the poor left high beam may be caused by the bulb burning out. The indicator light of the meter does not light up, which may be caused by the fault of the instrument or the poor contact contact of the combination switch. It is recommended that you go to the repair shop to check the replacement bulb and check the meter.

Hope it helps. [Car questions, ask the car master.] 4S shop professional technician, 10 minutes to solve. 】

Jetta tail light does not light up reason: check the bulb first, if the bulb is broken, you need to replace the bulb; Then check the line to see if it is caused by a short circuit in the line; Finally, check whether the safety line is disconnected, and if so, you need to go to the Weijing quiet repair shop to replace it.

The tail lights indicate the presence of a car in front of the rear car when driving at night, and show the position relationship between the two workshops, so they are installed on both sides of the rear of the car. It has enough luminous intensity so that the car tail light can clearly distinguish the signal for the driver or pedestrian of other vehicles even in bright daylight.

When driving at night, the light from the tail lights does not cause glare and uncomfortable feelings to drivers or pedestrians of other vehicles.

Turn signals are the most commonly used signal lights and turn on when a vehicle needs to steer. It should be noted that the time to turn on the turn signal should be turned on about 30 meters to 100 meters away from the turning intersection, and the slag should not be turned on until it has already reached the intersection, so that the trailing vehicle is caught off guard and causes a rear-end collision.

The headlights are available in two forms: high beam and low beam. Use low beam on cherry blossom roads with street lights in urban areas, and turn on high beams when driving on roads without street lights or highways. When meeting the car, the high beams should be turned off and replaced with low beams.

Tail light (brake light): When the brake light is on, it tells the vehicle behind that it is braking, pay attention to slow down. When you notice that the front taillights are on, be prepared to slow down as well.

Emergency Signal Lights (Double Flashing): Used in emergency situations such as temporary parking due to vehicle breakdown, and double flashing should also be turned on in bad weather with low visibility. Emergency lights are closely related to driving safety, so check whether they are working properly from time to time.

Night Running Indicator (Small Light): Used to display the width and length of the vehicle at night. When you can't see clearly behind you in the rearview mirror, you should turn on a small light, especially on a rainy day. (Photo by Zeng Caihong) @2019

The failure of the new Jetta high beam can be caused by a blown fuse, a burned out bulb, a faulty dimmer switch, poor grounding, etc. The details are as follows: Fuse blowing:

Turn on the headlight switch, the high beam and low beam are not on, first check whether the fuse box is blown. Lamp burning: It may be that the regulator is causing trouble.

The failure of the new Jetta high beam can be caused by a blown fuse, a burned out bulb, a faulty dimmer switch, poor grounding, etc. Details are as follows:

Fuse blowing:

Turn on the headlight switch, the high beam and low beam are not on, first check whether the fuse box is blown.

Lamp burning: it may be that the voltage regulator is faulty, and the voltage is too high; There is a short circuit between the generator armature and the excitation counterbalance magnetic coil.

The light switch is faulty:

When the live wire of the dimmer switch is overlapped with the high beam and low beam terminals respectively with a knife, the light is on, indicating that the dimmer switch is faulty.

Poor grounding: If only one headlight is on and the other is not, it may be that when the live wire of the dimmer switch is overlapped with the high and low beam terminals with a screwdriver, the filament is burned or the wiring is open, or the grounding is poor.

What is the new Jetta oil pan screw size?

The new Jetta oil drain screw is 14 cm, and the oil pan is fixed and destroyed by 7 cm.

Bottom drain screw introduction:

An oil pan drain screw is a screw that sits at the bottom of an engine's oil pan. When the engine needs to be changed and maintained, unscrew the screw to drain the oil from the original engine, and tighten the screw to add new oil from the oil filler port on the engine.

Functions of the bottom drain screw:

Most cars have wet oil pans, which are named wet sumps because the engine's crankshaft crank and connecting rod head are immersed in the oil pan once every revolution of the crankshaft to lubricate them. At the same time, due to the high-speed operation of the crankshaft, every time the crankshaft enters the oil pool at high speed, a certain amount of oil splash and oil mist will be stirred up to lubricate the crankshaft and bearings, which is called splash lubrication.

What is the reason why the high beams of the new Jetta are not lit? @2019

Hello, the 06-year-old Jetta has a high beam indicator light that is not lit, and there is no problem with the high beam operation, which is caused by the damage of the instrument itself or the false connection of the plug behind the instrument panel. The high beam indicator signal is sent to the instrument through the instrument harness, and when the high beam is turned on, the high beam signal line enters the instrument to control the high beam to be lit. After this fault can unplug the instrument, check whether there is a high beam signal on it, the signal is normal, the plug needs to be combined with the meter damage, there is no high beam, and the signal is that there is a problem with the instrument harness.

In this case, it is more troublesome to find the line, and the method of flying wire can be used to directly pass to the instrument from the output signal line of the combination switch, so that there is no need to replace and inspect the maintenance line.