What should I do if the gas stove can t catch fire when it s cold?

In the process of cooking in the kitchen, it is often encountered that the gas stove cannot be turned on, and it is very dangerous to light the fire with a lighter or match, so it is important to learn the correct way to light the fire.

Teach you why the gas stove won't catch fire.

If the gas stove can't catch fire, you don't need to ask someone to fix it, teach you a trick and solve it easily.

It may be that there is not enough natural gas: the gas stove burns for a period of time and automatically extinguishes, and there will be a sound of snorting energy, which may be caused by the lack of natural gas. You can check it first.

Broken gas pipeline: At this time, the gas main gate should be turned off immediately, and the gas stove switch should be turned off at the same time to prevent household gas leakage, and then repair it in time.

The ignition is broken: the ignition of the gas stove is broken, and the liquefied natural gas cannot be completely burned in use, and this situation may also appear to be open leakage, which is not only easy to be poisoned, but also prone to occur.

There are many reasons that need to be checked step by step:

1. It's out of gas. See if there is any arrears in the gas fee, whether the gas company has cut off the supply, and recharge in time if the gas fee is in arrears;

2. The battery is dead. Check whether the battery is depleted, it is recommended to choose a professional gas stove battery, and try not to use those "three no" battery products;

3. Overvoltage protection. Many gas stoves have overpressure protection function, once the overpressure will not start, at this time it is necessary to change a pressure reducing valve to try;

4. The ignition needle is not properly positioned. The gas stove has certain requirements for the distance between the ignition needle and the fire cover, and once it deviates too much, it will cause the situation that it cannot be ignited, which needs to be corrected;

5. Pipeline blockage. If the gas stove can smell the gas and does not catch fire, it is most likely that the gas stove pipe is blocked and needs to be dredged. If all of the above methods have been tried and still do not work, it is recommended to find a professional to repair it.

After boiling the soup overflowing the pot, the gas stove does not catch fire Solution:

1. Clean up the water and oil stains on the gas stove inside and out, pay attention: especially near the probe under the stove and near the switch, and disassemble the parts if necessary.

2. If the battery is soaked in water, you can remove the battery, wipe the water stains on the battery contact points, try to test whether the battery can be used, replace it if it can't be used, continue to install it if it can be used, try to ignite, if it is on fire or not on fire but there is a spark, it means that the battery and battery line are fine.

3. Check whether the stove eye is blocked and clean it up in time.

4. The battery is fine, but it still can't catch fire, which means that there is a problem with the probe. There are two on the stove: one is called a thermocouple (flame-out protection device).

A magnetic needle called ignition (pulse ignition device), if you find water stains during inspection, wipe it dry and try it on fire. Because the thermocouple uses the principle of thermal sensing, if the thermocouple breaks, the outlet valve is closed, so it cannot be lit with a lighter. If it is lit with a fire engine, it means:

The ignition magnetic needle was pasted, and it was wiped with sandpaper, or the solenoid valve was short-circuited.

<>1.The battery is insufficient, and the phenomenon is that the two burning eyes suddenly fail to ignite at the same time.

Solution: Follow the line of the lighter, it is easy to find a No. 1 battery on the opposite side of the lighter (near the wall), replace the battery.

2.The phenomenon of carbon blocking the burning eye is that the burning eye that is often used on the side of the external group cannot catch fire.

Solution: Just clean up the eye-burning part of the detachable cherry blossom with a toothpick and rinse it with water. (Cooking spills are treated in the same way and dealt with in a timely manner).

3.The rust clogs the burning tung and touches the orange eye, and the phenomenon is that the burning eye that is not often used on the inside does not catch fire.

Solution: The detachable part must be cleaned with a toothpick, and the stove buckle must be turned over and tapped, and the rust can be poured out.

This answer is applicable to most of the gas stove models of brands such as Midea JZT-Q230B && Fotile EMC5.

Fault cause analysis and solutions: 1. Power supply problem: check whether the AC power plug indicator is on, and first eliminate the problem of the power supply part.

2. Electric ignition failure: One of the pulse ignition and controller is faulty, and the water heater cannot be ignited normally. Other causes and solutions:

1. The smoke pipe cannot be exhausted normally. a.If the smoke pipe is blocked, clean up the smoke pipe blockage; b.

The smoke pipe is too long and not installed properly. 2. Solenoid valve failure: If only the ignition sound is heard during ignition, and there is no solenoid valve "click" magnetic suction sound, it may be:

a.The solenoid valve is damaged or aged, the solenoid valve is aging, it will be uncontrolled, and it can be sucked at the beginning of the ignition, and it can catch fire, but then it closes and turns off; b.If the gas pressure is too high or too low, the output pressure of the cylinder pressure reducing valve will be too high or too low in the water heater using cylinder gas, and the water heater cannot be ignited; c.

The solenoid valve has dirt. The solenoid valve cannot be overgased, and the gas (natural gas, liquefied petroleum gas, artificial gas) cannot come out, and cannot come out, so that the ignition cannot catch fire. Before confirming the quality of the solenoid valve, it is necessary to confirm whether the ignition control circuit is normal, if there is a fault, the solenoid valve cannot be controlled.

3. Problems with ignition porcelain needles or induction porcelain needles: aIt is very difficult to ignite when the ignition needle is offset or aging, and the ignition needle can be replaced or placed correctly; b.

Induction aging, you can polish the induction and place it well (so that the flame can fully burn the induction needle regardless of large fire or small fire). 4. Water pressure problem: a

When the water pressure is low, the water heater cannot start normally; b.The filter screen at the water inlet is blocked and the water cannot flow normally, so you can clean it up. 5. The valve seal is corroded by gas and then swells.

Replacement parts. 6. Failure of water-gas linkage device: a

The eardrum in the water-air linkage valve is aging or damaged, and the micro switch cannot be pushed; b.The micro switch is broken. 7. If the air source switch is not turned on or the air inlet filter is blocked, open the air source correctly and clean the air intake filter.

8. The gas type does not match; For example, if the liquefied gas water heater is connected to natural gas, etc., the liquefied gas water heater needs to be changed to natural gas before it can be connected and used. This answer is applicable to most of the gas stove models of brands such as Midea JZT-Q230B && Fotile EMC5.

Find out the reason why the gas stove won't catch fire first, and the reasons why this usually happens are:

1.Insufficient battery: When the gas stove battery is low, the ignition sound will be soft and weak, and the frequency of the discharge sound will be significantly slower than usual, if this is the case, you only need to replace the new battery to re-ignite.

2.Gas is not connected: If the sound is crisp and powerful when ignition, but it is not ignited, then you should consider whether the gas pipeline is unobstructed, you can check whether the gas pipeline is flattened or bent once, straighten it out and re-ignite.

3.Blocked fire holes or nozzles: Blocked fire holes in the burner head or fire cap will block the flow of gas and cause the fire to not ignite. This is possible by removing the fire splitter cover, then unclogging the lower nozzle hole with a thin iron wire or toothpick, cleaning the fire splitter cover and then trying to re-ignite.

4.Flame-out protection device: some of the modern new gas stoves have a temperature measurement safety device, which requires the nozzle to reach a certain temperature and put the pot on it before it can be stably burned.

5.Clogged regulator: If the air inlet and nozzle of the regulator are clogged with rust, it will also cause the gas stove to fail to ignite, at which point you should replace it with a new regulator and try to re-ignite.

The gas stove won't catch fire? Teach you how to solve it.

Teach you why the gas stove won't catch fire.

If the gas stove doesn't catch fire, don't spend money to fix it, try this trick and fix it easily.

First, check whether the air source switch is on. Check that the connecting hose is not flattened or bent. If the gas stove does not catch fire, if it does not ignite, check whether the discharge needle is discharged; If the discharge needle does not discharge, it is a failure of the discharge needle and the discharge needle should be replaced; If the discharge needle discharges, replace the battery, and then see if the flame in the middle can burn the probe on the broken side, and the probe must be burned to fix the fire.

When igniting, press and hold for ten seconds, and then release the switch, until it is hot, in order to fix the fire. Extended Information: Gas Stove Maintenance Tips:

1. The gas stove should be cleaned regularly, and the oil stains generated by the gas stove after a period of use not only affect hygiene but also easily cause gas stove blockage, so the gas stove needs to be cleaned regularly. 2. Stove maintenance and inspection, find professionals to repair it, and regularly check the air tightness of the stove and gas supply system with foaming agent. 3. Cleaning of the stove to the cleaning of the stove tiles.

Use discarded candle heads, the surface of the candle is smooth, even if there is oil stained on it, as long as the ordinary dish soap is mixed with water and gently wipe it, gently apply the seams of each tile, first paint in the direction of the seam, and then apply it horizontally, be sure to make the thickness of the candle equal to the thickness of the tile. 4. Cleaning of the fire frame and gas outlet holes: cleaning the fire frame and gas outlet holes of the gas stove. Fill a pot of water and boil all the stove racks in it, and when the water is hot, the sticky dirt will decompose and peel off.

To prevent the burner vent from being blocked, remove the burner once a week and clean the vent with a toothpick. The carbide and scorch crumbs accumulated on the burner can be removed with a small brush, or the fire hole can be pierced with a thin wire.