How to debug the Gauss Bell satellite pot, how to debug the Gauss Bell satellite cauldron TV receive

To give you the detailed amount introduced there.

How to debug the Gauss Bell satellite cauldron TV receiver Hello dear, press the 'info' button to see that the signal strength should reach more than 70, otherwise the feeder or f head is bad. The signal quality should reach more than 40, otherwise adjust the pot: the high-frequency head is 44cm away from the center of the cauldron, and the 0 scale marked on the top of the high-frequency head is adjusted to be parallel to the ground.

Adjust the elevation angle of the seat and rotate the direction of the pot at the same time to maximize the signal quality. Find a station with a strong signal [such as a TV guide], press the [Info] button, the lower limit frequency should be 04060, the symbol rate should be 27500, and the polarity should be vertical. Signal strength of 0 or very rarely the receiver to the high-frequency head cable is not properly connected.

If the signal quality is 0 or very rarely, the direction of the cauldron is inaccurate, the polarization angle of the high-frequency head is inaccurate, and the elevation angle is inaccurate. Press Menu-Settings-Add-Device. Hope it helps.

The Gaussbell cauldron satellite dish decryption method is as follows:

Second, for example, the password of Gauss Bell and other receivers is.

Methods for adjusting satellite programs for reference:

First, select Device Settings - New Device. Enter the satellite program parameters for a Zhongxing-6b. The parameters used are in the southeast of Fujian.

At this time, only the signal strength is more than 70%, and the signal quality is zero or very small, indicating that the connection is correct. It's just that the azimuth and elevation angles are not adjusted well. Rotate the azimuth, the hole is vertical and see if the signal quality changes, as long as there is a small change, it means that the satellite signal is captured, and then carefully adjust the azimuth and elevation angles to make the signal quality reach the maximum.

As long as you adjust carefully, you will be in the best condition. After adjusting, press the OK button and it's OK. This is aligned with the satellite.

Gauss Bell (2003): Restore factory settings Confirm Program Plus Program Decrease Volume Plus Volume Decrease 1234, you can enter the blind scanning function.

Gauss Bell (little prodigy, challenge searcher) 2004 production: restore factory settings to confirm (screen display "please enter password"), dust trembling calendar password is "5678". To enter the Internet search, you also need to enter the password "5678".

Gauss Bell: Factory reset ok program on program under volume down 1234. Factory reset OK 5678.

Gauss Bell-S80E: Bring up the main menu, move the cursor to the "factory reset parameters" item, press confirm, a box appears in the lower right corner of the screen, there is a prompt text "enter password", press "5678" with the remote control, and then the screen displays "system information data storage", three seconds later, the menu automatically exits, and the main menu is called up again, and it is found that there is an additional "automatic search" item below the "perpetual calendar" item, enter the item, set according to the corresponding parameters, and then press confirm.

How to set up all Gauss Bell models: You need to change the menu to an English menu Select the default setting OK Mute + Channel Up Key Enter up, down, left, right OK to resume blind scanning and preset programs.

Zhongjiu satellite is encrypted,All copycats can't watch normally,There's no good way to crack it for the time being,Don't worry,The black box manufacturer will soon come up with a countermeasure,Then the set-top box can be upgraded,

First of all, anti-interference has nothing to do with the brand of the device.

Reduce the installation height of the satellite pot, find a natural shield such as a wall, block interference, and eliminate weak interference.

But for the stronger interference will not be improved, only radio professionals can solve it, because they have equipment for interference signal testing, interference radiation belongs to the management of the Radio Administration, you can complain! But it's best to provide relevant evidence to solve it quickly, I hope it can help you.