A broadband cat, a switch, and the network cable in each room are pulled to a power box, if each roo

In this case, you need to divide the main router and the secondary router.

1. How to set up the main router:

1. Plug the network cable (bus) into the WAN port of the wireless router, plug one end of the network cable into any LAN port of the wireless router and connect the computer network card at the other end, and turn on the power supply of the router.

3. Then enter admin, the default account name and password are the same (there is also a prompt for the original data on the back of the router) to confirm.

4. After entering the wireless router setting interface, select the Internet access method according to the setup wizard (different broadband options are also different), and enter the Internet access and password.

5. Save and continue to set the wireless key, (it is recommended to use a combination of numbers and English for the password, and it is best to use the @ symbol in the middle, so as to prevent others from rubbing the net).

6. After saving, you can surf the Internet normally.

7. If it is abnormal, you may wish to click the reset button of the wireless router and set up the router again.

Second, the setting method of the secondary router:

1. Do not connect the secondary router to the main router first.

2. One end of the network cable is connected to any LAN port of the secondary router, and the other end is connected to the computer.

3. Change the LAN port IP of the login interface through the computer browser to avoid conflicts with the IP segment of the main router;

4. WAN port Internet access mode selection: dynamic IP connection, enable DHCP server.

5. Wireless settings and keys, save and exit.

6. Connect a network cable from any LAN port of the main router to the WAN port of the secondary wireless router, and the computer can access the Internet at this time.

7. Reconnect the router as long as the LAN port is changed to sequential, and the other settings are the same as the secondary route settings.

Dear users, hello.

Hope the following can be helpful to you:

It is recommended that you connect the router through the broadband modem, set up automatic dial-up networking, and then connect the router to each room and choose to automatically obtain the IP address to access the Internet.

Anhui Telecom will serve you wholeheartedly.

Summary. Hello, dear. What you asked ( The outdoor network cable enters the weak current box and is connected to the optical modem, the optical cat is connected to the router, the router is connected to the switch, and then the switch pulls 6 network cables to each floor, and each floor is two network cables, the original plan is to connect one to the TV and one to a wireless router, and now it is planned to use only one network cable to connect the router and then connect the router to the TV, but I don't know whether it is good to use two connections or one connection.

Here's the answer: one connection is good for <>

According to you, unless you are a network set-top box, or have two network cables, no.

Because IPTV requires a separate dial-up, you need to directly connect to the IPTV or ITV port of the optical modem.

The outdoor network cable enters the weak current box and is connected to the optical modem, the optical cat is connected to the router, the router is connected to the switch, and then the switch pulls 6 network cables to each floor and each floor of two network cables.

Hello, dear. What you asked ( The outdoor network cable enters the weak current box and is connected to the optical modem, the optical cat is connected to the router, the router is connected to the switch, and then the switch pulls 6 network cables to each floor, and the original plan is to connect one to the TV and one to the land hall to a wireless router, and now the plan is only to use a network cable to connect the router and then connect the router to the TV. To provide you with the answer as follows:

One connection is good for <>

According to you, unless you are a network set-top box, or have two network cables, it is not possible because IPTV needs to be dialed separately, and you need to directly connect to the IPTV or ITV port of the optical modem.

It is a built-in set-top box for TV.

The network cable is plugged directly into the TV.

Wait a minute, dear

Hello pro TV built-in set-top box with 2 connection method Oh <>

Suggested Connection:

Cats – routers – switches.

The cat LAN is connected to the WAN port of the router, and the LAN port of the router is connected to 4 network cables (there are four LAN ports), and one of the network cables is connected to the subordinate switch.

In this scenario, all computers choose to get IP and DNS automatically.

The router uses PPPoE dial-up mode to access the Internet (DHCP is enabled).

The specific network topology diagram is as follows:

Telecom Cat (LAN) --WAN) Router (LAN) 1--- Computer (Room 1).

lan)2 -- Computer (Room 2) (LAN) 3--- Computer (Room 3) (LAN) 4--- Switch (Room 4) Computer.