How to use hydraulic pipe crimping machine?

1. The operator must operate according to the process regulations.

2. After the machine is out of use, the power supply must be cut off.

3. When changing the mold, it must be carried out after the shutdown.

4. The joint surface between the mold base and the mold should be kept clean, and there should be no hard objects such as metal scraps.

5. Inject lubricating oil on the inclined plane of the mold base before starting.

6. The positioning screws must be tightened before installing the module.

7. a pressure regulating valve.

It must be adjusted at the specified pressure.

8. It is strictly forbidden to put your hands inside when working.

9. When overhauling the electrical part, the electrical safety regulations must be observed.

The operation and use of the hydraulic pipe bender and the matters to be paid attention to:

1) Wheel formwork.

Installation: a. Remove the fixed nut of the wheel mold in a counterclockwise direction. b. Put in the wheel mold, and then lock the wheel mold fixing nut.

2) Clamping mold.

Installation: a. Pull out the clamping mold to fix the centering shaft. b. Put the clamping mold in, and then insert the fixed mandrel.

Adjustment: a. Fix and relax the clamping mold base, then put the control panel into manual mode, press the clamping button to the end of the clamping mold path. (At this time, there needs to be a gap between the wheel mold clamping molds, and the clamping mold holder adjustment screw can be adjusted).

b. Adjust the clamping mold base and adjust the screw to make the clamping mold and the wheel mold completely sealed.

c. Press the clamping button to make the clamping die retreat, and then rotate the clamping adjustment screw clockwise for about 1 2-1 4 turns.

d. Then lock the clamp die holder fixing nut.

3) Guide mold.

Installation: a. Remove the fixing screws of the guide mold, and then put the guide mold in.

b. Lock the guide screws.

Adjustment: a. Loosen the fixing nut of the guide formwork, then put the control panel in manual mode, and press the clamping button to the end point of the guide mold path (at this time, there must be a gap between the wheel mold and the guide mold, which can be adjusted with the guide mold adjustment screw.)

b. Adjust the guide seat and adjust the screw to make the guide mold and the wheel mold completely sealed.

c. Press or withdraw the clamp button, and then turn the guide mold adjustment screw clockwise about 1 2-1 4 turns.

d. Then lock the fixing screws of the guide mold base.

4) Mandrels. Installation: a. Put the mandrel into the core rod in a clockwise direction.

b. Then fix the mandrel fixing screws. (Please pay attention to the direction in which the mandrel must be bent in accordance with the elbow).

First of all, access to the power supply, the pipe press machine is energized, plus the hydraulic oil, you can start the machine normally, when crimping the hydraulic pipe, first select the appropriate crimping mold, adjust the fine-tuner, and finally crimp the hydraulic pipe, after the crimping is completed, measure whether the size of the hydraulic pipe after crimping is qualified.

1. The operator must operate according to the process regulations.

2. After the machine is out of use, the power supply must be cut off.

3. When changing the mold, it must be carried out after the shutdown.

4. The joint surface between the mold base and the mold should be kept clean, and there should be no hard objects such as metal scraps.

5. Inject lubricating oil on the inclined plane of the mold base before starting.

6. The positioning screws must be tightened before installing the module.

7. The pressure regulator must be adjusted under the specified pressure.

8. It is strictly forbidden to put your hands inside when working.

9. When overhauling the electrical part, the electrical safety regulations must be observed.

1. For a good grounding connection, an automatic pipe bender must be used, and the cable should not be less than 4mm2 copper cable. The power supply voltage must not exceed the size of the regular excitation. Plugs cannot be inserted and unplugged. The control loop cannot be measured with a megohmmeter, otherwise the equipment may be damaged.

2. When plugging and unplugging the connector, do not pull out the cable or cable to prevent the soldering from falling off.

3. You can't hit the switch with hard objects, such as on/off switches, encoders, etc.

4. Do not touch the human-machine interface with sharp objects.

5. The electrical box should be placed in a ventilated place to prevent the action of dust and corrosive gases.

1. In order to connect the clump rock with good grounding, an automatic pipe bender must be used, and the cable should not be less than 4mm2 copper cable. The supply voltage cannot exceed the regular size. Plugs cannot be inserted and unplugged. The control back stool Zheng Shilu cannot be tested with a megohmmeter, otherwise the equipment may be damaged.

2. When plugging and unplugging the connector, do not pull out the cable or cable to prevent the soldering from falling off.

3. You can't hit the switch with hard objects, such as on/off switches, encoders, etc.

4. Do not touch the human-machine interface with sharp objects.

5. The electrical box and jujube limbs should be placed in a ventilated place to prevent the action of dust and corrosive gases.

Refer to the instruction manual of the electric oil pump.

First, screw the working cylinder into the internal thread of the square gear block, so that the wheel mounted on the bracket at the rear end of the cylinder is downward.

Select the die head according to the outer diameter of the bent pipe, put it on the plunger, put the groove corresponding to the two rollers towards the die head, and then put it into the corresponding size of the pattern plate hole, then cover the upper flower plate, insert the bent pipe into the groove, and then pull back the movable part of the quick connector at the end of the high-pressure oil pipe and put it on the joint of the working oil cylinder, and tighten the oil drain screw on the electric oil pump to bend the pipe.

After the bending is completed, relax the oil drain screw, and the plunger will automatically reset.

1. In order to make a good grounding connection, an automatic pipe bender must be used, and the cable should not be less than 4mm2 copper cable. The supply voltage cannot exceed the regular size. Unable to plug in and out of the plug. The control loop cannot be tested with a megohmmeter or it may damage the equipment.

2. When plugging and unplugging the connector, do not pull out the cable or cable to prevent the soldering from falling off.

3. You can't hit the switch with hard objects, such as on/off switches, encoders, etc.

4. Do not touch the human-machine interface with sharp objects.

5. The electrical box should be placed in the Tongkai wind to prevent the action of dust and corrosive gases.