What s going on with the faucet of a fully automatic washing machine

If you want to use a special faucet, you can buy it at the plumbing store. There is a structure at the outlet of the faucet, and there is a steel ball at the head of the washing machine inlet pipe, which is just stuck in that structure, which is very convenient and will never leak.

The most common is caused by damage to the water-stop tape that ties the faucet part (fixing screw). In this case, simply remove the faucet with a wrench and re-roll the new water-stop tape where the fixing screws are.

Installation: 1) Hold the connector in one hand and pull down the buckle with the other hand to separate the connector from the water inlet pipe.

2) Unscrew the 4 fastening screws on the upper connector and unscrew the connector so that there is a gap of 3 threads between the upper and lower connectors. If the faucet is too thick, you can remove the plastic guide sleeve inside.

3) Adjust the 4 screws of the connector evenly so that the 2 screws on the wall side are in full contact with the outside of the faucet. Screws close to the wall can be screwed in by hand beforehand.

4) Place the upper connector against the faucet so that its inner sealing ring is in full contact with the faucet. Note: The seal cannot be removed, and the mouth of the faucet must be flat.

5) Rotate the 2 screws on the opposite side of the wall to make it contact with the faucet, and then tighten it with a screw.

6) Rotate the lower connector until the upper and lower connectors are tightened into position. The gap between the two is less than 3mm.

7) Press down on the buckle of the gold market tube.

8) Insert the water inlet pipe up into the lower connector and release the clasp.

9) Check whether there is water leakage, if it leaks, it needs to be reinstalled. Note that the faucet should use a standard faucet. The above is the information compiled by the installation of pipes and fully automatic washing machine faucets, I hope it will be helpful to your life.

You should buy a faucet for a fully automatic washing machine.

I connected it with an exclusive faucet for the safest.

All the problems will be solved.

You can go to the hardware store and buy an adapter 、、、 for the faucet

You make it clear to your boss and he will know 、、、

This is also the case with our washing machine, which can't be used when you buy it.

It must be left on all the time, and then since the fully automatic washing machine has an inlet valve, the opening and closing of the valve is passed. to control whether water enters the washing machine, so your faucet will only be used if the inlet pipe is removed. Usually when you are washing clothes, you must keep the tap in the position where the water supply is always on.

When washing in a fully automatic washing machine, the faucet must be on all the time. The water inlet of the fully automatic washing machine is automatically controlled by its program through a solenoid valve. The solenoid inlet valve is closed under normal conditions, and the solenoid inlet valve will be opened only after the power supply is started.

When using a fully automatic washing machine for laundry, the power is turned on first, the faucet is turned on, and the washing selection, washing program and water level are set.

The faucet must be left on all the time during the operation of a fully automatic washing machine. When the laundry is done and the washing machine is not used, the faucet can be turned off.

The water inlet pipe of a fully automatic washing machine can be plugged into the faucet all the time, but it is recommended to turn the faucet off after washing clothes to prevent water leakage caused by the water inlet pipe falling off.

The automatic washing machine and faucet must be turned on when washing clothes, and the faucet should be turned off after the clothes are washed.

If you don't use it, you can naturally relate to the faucet. But if you want to use it, you need to keep it open all the time.

In addition, the water valve control of the washing machine is set with automatic switch, and if the washing machine does not need to supply water, it will automatically be related, and the function of the faucet is the same, so there is no need to worry about wasting water.

When you use it, you don't need to open it, it is automatic water addition and automatic drainage. When you run out, you can turn it off.

The method of connecting the faucet to the automatic washing machine: (1) Use the special faucet for the washing machine, and plug it in directly. (2) Use ordinary faucets:

The length of the inlet pipe of the washing machine is generally about 1m. One end is the connection to the washing machine, and the other end is the connection to the faucet. The connection to the washing machine is very simple, the inlet pipe connection seat is placed vertically on the inlet valve port and screwed in a clockwise direction.

1. Step 1: Hold the connector with four screws in one hand, and pull down the buckle of the water inlet pipe with the other hand to separate the connector from the water inlet pipe. 2. Step 2:

After confirming whether the white plastic guide sleeve and black rubber pad in the connector are in good condition (if the diameter of the faucet pipe is too thick, you can remove the plastic guide sleeve), loosen the four screws on the connector, and rotate the upper and lower connectors to leave a gap of 3-4 threads. 3. Step 3: Connect the connector horizontally to the faucet and tighten the four loosened screws.

4. Step 4: Tighten the connector with 3-4 threads reserved in advance until it does not leak.

1. Take out the water inlet pipe fittings of the automatic washing machine, find the end with the water inlet pipe joint, and then press down the slider to separate the water inlet pipe joint from the water inlet pipe.

2. Loosen the four screws on the inlet pipe joint evenly until the faucet can be inserted, if the faucet is too large, you can remove the bushing. Then loosen the plastic joint nut until about 3-4 turns of thread are exposed.

3. Put the water inlet pipe joint on the faucet, put the black washer in the joint close to the faucet, then tighten the screws with a screwdriver, tighten the plastic interface nut, and tighten until it stops without leakage.

4. Then connect the water inlet pipe and the water inlet pipe joint, connect the other end of the water inlet pipe with the water inlet of the automatic washing machine, tighten the plastic nut, and the device is completed.

5. Don't forget to open the water valve after completing the installation, so that the washing machine will automatically enter the water when it starts.

The method of connecting the fully automatic washing machine and the faucet is as follows:1Determine the type of faucet:

Faucets are divided into two types: internal threads and external threads, and you need to choose the corresponding connector according to the type of faucet. 2.Prepare the connector:

Choose the right connector, connect one end to the faucet and the other end to the washing machine water inlet. 3.Installing the connector:

Screw one end of the connector into the faucet and the other end into the washing machine inlet and tighten it. 4.Test Connection:

Turn on the faucet, check whether there is water leakage at the connection, if there is water leakage, you need to adjust the connector again. 5.Complete the connection:

After the connection is successful, plug the washing machine into the power supply and follow the washing machine manual. Notes:1

During the connection process, the front suspect needs to ensure that the threads of the connector and the faucet are the same, otherwise it will lead to a loose connection and water leakage. 2.During the connection process, it is necessary to ensure that the gaskets of the connector and faucet are complete, otherwise it will also lead to water leakage.

3.In the process of use, it is necessary to regularly check whether there is water leakage at the connection, and if there is water leakage, it needs to be dealt with in time.

The connection between a fully automatic washing machine and a faucet requires the following attention:

Choose the right fittingGenerally speaking, the joints used in automatic washing machines and faucets should be standard household faucet connectors, but because the size of the joints of washing machines in different regions and different models may be slightly different, it is recommended that when purchasing connectors, Lianghuai should confirm whether they meet the connector specifications of the washing machine. Shelter ruler.

Confirm the faucet location: Before installing the washing machine, it is necessary to confirm whether the position of the faucet is able to meet the connection requirements of the washing machine. In general, the faucet should be on the side or back near the washing machine, which is convenient for connecting the water pipes.

Connect the water pipes: To connect the water inlet of the washing machine to the water pipe of the faucet, it is usually necessary to use a pair of heads. One end of the connector is connected to the faucet, and the other macro key is connected to the water pipe at the high end, and the connection can be made stable and not leaking by adjusting the joint.

Check the connectionAfter connecting the water pipes, you need to check whether the water pipes, joints and faucets are stable and whether there are any water leaks. If necessary, the joints can be treated with water pipe sealant to prevent water leakage.

The faucet of the washing machine can be left on all the time. When there is no water, the current automatic machine is automatically filled with water, as long as the faucet is opened, the machine can complete the automatic water filling automatic stop, very convenient, no need to stare at a person as before, machine control, waiting for the time when there is no need for water, even if the faucet is opened, there will be no water, basically the clothes are not in charge. Most homes have a washing machine.

So, after using the washing machine, should you turn off the faucet switch?

In fact, the water inlet of a fully automatic washing machine is controlled by the program of the washing machine itself. It is automatically controlled by a solenoid valve inside the washing machine.

Target. That is, even if you turn on the faucet switch provided to the washing machine, the water will not flow if the solenoid valve on the washing machine is not opened. However, when the solenoid valve is closed, the water supply line connecting the faucet to the washing machine will be under negative pressure.

Therefore, in order to avoid pipe bursts, it is recommended that everyone turn off the faucet switch after using the washing machine.

Usually in the process of using the washing machine, we will also encounter the situation of dripping water at the contact between the faucet and the water supply pipe of the washing machine. How to solve such a problem? Here's a trick.

It's easy to do with a single rope. Take a rope and hook it in half at the junction of the water pipe and the faucet. Pick up the right rope and wrap it around the faucet from below.

At this time, we can see a knot appear in the string of the faucet. Then, we have to pass through the knot on the right hand side. Finally, pull the strings on both sides of the faucet tight.

In this way, after tying, there will be no dripping at the interface between the water pipe and the faucet.

The above is a detailed interpretation of the problem, I hope it will help you, if you have any questions, you can leave me a message in the comment area, you can comment with me, if there is something wrong, you can also interact with me more, if you like the author, you can also follow me, your like is the biggest help to me, thank you.