The car s anti skid lights are on, and you can t hit the car

Hello vehicle anti-skid light is on and its vehicle cannot start normally, and then it is recommended to check whether the battery is caused by insufficient voltage, or check whether the vehicle wiring harness is faulty and the line is faulty.

When the vehicle is out of control such as tail flick and side skidding, the ESP electronic stability system will intervene in time and correct the driving trajectory of the vehicle, and the ESP indicator light on the instrument will light up at this time, indicating that the ESP system is working, and ESP is also an important system in the active safety system of the car.

This indicator is not manually turned on, but is connected to the whole system, please note that the ESP system can be turned off manually, not manually turned off or on! There is no point in turning on this light, it should be said that it is a manual to turn on or off the entire ESP system.

Usually in the fierce sports driving, such as playing tail flicking, drifting or direct racing, etc., are to turn off the ESP, if not closed, once the vehicle is out of control when the ESP will immediately intervene, so it will affect the car, of course, in daily driving ESP is turned on by default, after all, this thing will play a very important role in driving safety.

It may be that the sensor is broken, if there is navigation, it may be navigation interference, the tires may be skidding, the car judges that the vehicle may be out of control, use the computer to check the ABS sensor to eliminate the fault, and solve the ABS light, and the anti-skid light will not be on.

A solid ABS light indicates an anti-lock braking system alarm. Under normal circumstances, the light will turn on when the ignition switch is turned on or the engine is started, and the system enters the automatic detection program, and after the detection is completed, the light is turned off. If the light does not turn on after turning on the ignition switch, or does not go off after it is on, or lights up while driving, it indicates that the system is faulty.

Extended information: If the ABS warning light and the braking system warning light are lit at the same time while driving, it means that both the ABS and the braking system are faulty, and the braking characteristics will be mutated. If the latter is the case, you must stop driving immediately, check the level of brake fluid, and if the fluid is at the "min" mark, you must not continue driving and must be serviced by a professional.

If the liquid level is normal, it indicates that the ABS system may fail, that is, the adjustment function of the ABS system fails, and only the ordinary braking system plays a role, which is easy to cause the rear wheels to lock up quickly when braking, resulting in side skidding. At this time, you should drive with caution and carry out repairs as soon as possible.

The car's anti-skid lights are on, and you can't hit the car. Because the anti-slip light is on, your anti-slip switch has been turned on. Or it's off. Hurry up and put the anti-slip. The switch is on.

The anti-skid light of the car is on, and the car cannot be hit, so it is recommended that it is best to go to the after-sales service of the car to test the fault code, and judge the specific cause of the problem of the car through the fault code.

The anti-skid light on the dashboard may be that the road surface is indeed slippery, causing the ABS to work, so it will light up; ABS pump failure; If there is an error in signal transmission, if the computer's false alarm is lit up for a long time, it will definitely be a problem, so it should be repaired as soon as possible. If it turns on for a short time and then goes out naturally, then the first possibility is relatively large.

1. Mistakenly pressing the close button of the ESP;

2. The sensor terminal is loose or malfunctioning;

3. Short circuit of the line or blowing of the relevant fuse;

5. Poor signal transmission caused by software problems;

6. ABS pump body failure.

There are two ways to cancel anti-slip (ESP) lights:

Restart the engine and press the ESP OFF button on the vehicle to see if the ESP is turned off by mistake;

To go to the 4S shop for maintenance, use a special fault diagnostic instrument to find the fault, and after repair, please remove the fault code with the decoder to ensure that the ESP works normally.

If it turns on once in a while and then goes off, then the electronic body stability system system is activated while driving, which is normal.

If it keeps on, then the electronic body stability system is faulty, then turn off the body stability system switch, then turn it on, then turn off the engine and the power of the whole vehicle, wait for about a minute, and then start the engine to see if it is still always on.

If it is still on, then you need to go to the 4S store to check the fault code.

In most cases, it is not necessary to deal with it, and it is sufficient to eliminate the fault code, but it is also possible that the sensor is faulty or the instrument control unit is faulty, and the damaged part needs to be replaced.

You've turned on the anti-slip mode.

2. The sensor terminal is loose or malfunctioning;

3. Short circuit of the line or blowing of the relevant fuse;

5. Poor signal transmission caused by software problems;

6. ABS pump body failure.

We hope you find it helpful

The illumination of the anti-slip light indicates that the ESP electronic stability system is faulty.

The ESP system integrates the functions of ABS (anti-lock braking system) and ASR (drive anti-skid system), which can monitor the driving status of the vehicle in real time. The ESP consists of three parts: an electronic control unit, a signal input device, and an actuator. When an ESP fails, it is caused by the following reasons:

First, the ESP switch is manually cut off, so the ESP lights up. There is an ESP switch in the cab that allows the ESP function to be turned off manually. If you press the ESP switch, the ESP warning light on the instrument will light up to indicate that the ESP is off.

When processing, we press the ESP switch and turn the ESP function back on to eliminate it.

Clause. Second, the steering angle position sensor is damaged. The steering angle position sensor is located under the steering wheel, and transmits the steering wheel steering wheel rotation signal to the control unit, if the sensor is damaged and there is no signal, the vehicle cannot determine the direction of travel, and the fault light is on.

Clause. 3. The lateral accelerometer sensor is damaged. The sensor is used to determine whether the vehicle is affected by the lateral force of the slip action and the magnitude of the force, if it is damaged, the body computer can not confirm whether the vehicle is slipping, and the fault light is on.

Clause. Fourth, the brake fluid pressure sensor is damaged. The sensor is installed inside the hydraulic control unit and is used to detect changes in brake fluid pressure when the driver is braking. If damaged, the ESP system will be ineffective, and the instrument will light up the ESP anti-skid light warning.

Clause. 5. The yaw angle velocity sensor is damaged. The sensor is used to detect the angular velocity of the car's rotation around the vertical axis, determine whether the vehicle is rotating along the vertical axis, and provide the rotation rate.

If this sensor fails, the control unit will not be able to recognize whether the vehicle has steered or not, and the ESP function will fail.

Clause. 6. Failures related to ABS and ASR systems will cause ESP faults to light up. For example, ABS sensor damage, brake light switch disconnection, hydraulic control unit, etc.

Anti-lock braking system, brake pressure sensor is different from Li Chang.

This sensor is mainly installed in the hydraulic control device, and its function is to check the owner's braking operation of the vehicle to understand the change of brake fluid pressure. When the brake pressure sensor is damaged, the ESP system will be affected, which will cause the anti-slip Zen field to turn on.