What s the use of pressing 06 on your phone

06 shows your phone's trombone.

The number that comes out is the IMEI code, which is the serial number of the mobile phone.

The serial number of the mobile phone is the same as the person's ID card, one machine and one number, and three codes in one. The number that appears on the mobile phone by pressing * should be consistent with the number on the outer box of the mobile phone and the number posted on the motherboard of the mobile phone.

The serial number of the mobile phone is the unique identification code for inquiring about the warranty and going to the customer service outlets to enjoy the warranty service.

It is a mobile phone command, and the IMEI number of the mobile phone will be displayed after entering.

This is what is commonly referred to as the serial number of the mobile phone.

Mobile phone "serial number". Press * on the dialing interface to display the IMEI number of the phone.

Mobile phone instructions refer to the input of certain key combinations on the mobile phone, and some Gong Zen Jian Min can appear. Depending on the phone, the instructions may vary.

In most terminal devices, it can be queried by dialing in *. You can also use the at command, atd* or at+cgsn.

Dialing * on the dial interface can put your Android phone into engineering mode.

1. After entering * * in the dial pad, you can directly enter the engineering debugging interface.

On the test screen, you can view "Mobile Phone Information", battery information, usage statistics, and Wi-Fi information

This is the "Mobile Information" screen. Here we can get the IMEI, mobile phone number, current mode, signal strength and other underlying hardware status information.

The figure below shows the "Battery Information" interface, where we can read the battery voltage, health status, and the operating time from start to this time. If this indicates that your battery status is "poor", maybe you should replace the battery.

In the "Usage Statistics" section, you can see the total length of time the software has been running and the number of times it has been used. If you notice that your phone has been losing power faster than before, but it has been turned on less often and used for more time, you may want to include it in the rogue software.

In "WLAN Settings", you can perform some WLAN debugging, mainly to view the saved WiFi setting information of the machine, WLAN status, and ping test.

Also, if you are not very clear about the settings inside, please do not change them at will, otherwise it may cause irreparable losses.

Engineering mode, as the name suggests, is the mode used by engineers to debug mobile phones. It seems unfathomable, but in fact it is not as complicated as everyone thinks, we can get some base station information in it, such as signal strength, battery status, mobile phone running time, background software running time, and of course, you can also debug WLAN.

It is not recommended for general users to enter engineering mode.

Summary. Hello, glad to answer for you. Kiss, the mobile phone press* is a mobile phone instruction, after entering, the mobile phone's IMEI number will be displayed, that is, the commonly known mobile phone serial number, mobile phone "serial number".

Press * on the dialing interface to display the IMEI number of the phone.

What is the phone used to press * for.

Hello, glad to answer for you. Kiss, the mobile phone press* is a mobile phone instruction, after entering, it will display the IMEI number of the mobile phone, that is, the commonly known mobile phone serial number, mobile phone finch manuscript boring "serial number". The mobile phone will press * on the corner of the dial boundary to display the IMEI number of the hand-held barcoder.

Mobile phone instructions refer to certain functions that appear by entering certain key combinations of Tehong Radine on the mobile phone. Depending on the phone, the instructions may vary. In most terminals, you can dial in * to query.

You can also use the at command, atd* or at+cgsn.

Mobile phone serial number, serial number, can it be used to monitor mobile phone?

Kiss and kiss, it cannot be used to monitor the phone.

The mobile phone press * is to query the identity code of the mobile phone used by Zhijian, that is, the international mobile equipment identity code (IMEI: international mobile equipment identity).

The International Mobile Equipment Identity (IMAI) is a mark that distinguishes a mobile device and is stored in a mobile device that can be used to monitor stolen or invalid mobile devices. The International Mobile Equipment Identifier is a 15-digit number"Electronic serial number"It corresponds to each mobile machine one by one, and the code is the only one in the world.

It doesn't mean anything in particular.

If you're not mistaken, you actually want to press *. This function is that after you press it, the mobile phone will automatically pop up the IMI code of the mobile phone, which each mobile phone has, which is to identify the authenticity of the mobile phone.

Meaning of Other**

Mobile phone IMEI setting query (mobile device ID).

Call forwarding. *21* The **number you want to transfer to*10, press ** Jian to transfer all incoming calls to voice transfer.

21*The **number*20 you want to transfer to, press **Jian, all incoming call data transfer.

21*The **number*12 you want to transfer to, press **Jian, all incoming calls and faxes are transferred.

, press ** Jian to check the status of all incoming call transfers.

, press ** Jian to cancel all call transfers.

61 * the **number you want to transfer to*10* the number of seconds to wait, press ** Jian No Answer voice transfer.

61 * the **number you want to transfer to*20*the number of seconds to wait, press ** Jian No Answer Data Transfer.

61 * the **number you want to transfer to*10* the number of seconds to wait, press ** Jian No Answer Fax Transfer.

, press ** Jian to query the status of no answer transfer.

, press ** Jian to cancel the transfer without answer.

62* You only shout the **number * 10 that the macro wants to transfer to, press the ** health and cannot connect to the voice transfer.

62*The **number you want to transfer to*20, press ** Health to not connect to the data transfer.

62*The **number you want to transfer to*12, press ** to make *** health and cannot connect to fax transfer.

, press Electrolytic Xun Jian to inquire about the status of unreachable transfer.

, press ** Jian to cancel the unreachable transfer.

67 * the **number you want to transfer to*10, press to call** Jian is busy voice transfer.

67 * The **number you want to transfer to*20, press ** Jian to transfer the data in case of busy.

*67* The **number you want to transfer to*12, press **Jian to fax the transfer.

, press ** Jian to inquire about the status of busy transfer.

, press ** Jian to cancel the busy transfer.

, press Hit Jian to cancel any type of call forwarding.

Call waiting. , press Hit Jian to set up call waiting.

, press Hit Jian to cancel the call wait.

, press the fingerbook to check the status of the call waiting.

Caller ID display and caller ID display limit query.

, press the caller number to show whether to open the query.

, press the caller number to display the restriction status query.