Who knows how the hydraulic baler is not energetic and can t be tightened

The pressure is not enough, generally the oil seal is not sealed well, resulting in pressure relief, or the pressure caused by oil leakage can not be reached, if your machine is only this problem, it can be determined that the pressure is insufficient. It is recommended that you check whether the seal is damaged or the oil pressure is leaking.

The baler is divided into automatic baler, semi-automatic baler, unmanned baler, etc., and the baling belt used is different according to the baler. When we use the baler, we often have some phenomena such as the baler is not tightly packed, so what is the reason for this phenomenon? How can we fix it?

Let's analyze the reasons for this phenomenon.

1.The balance position of the baler crossbar is not well adjusted.

2.The gap between the untie rollers is relatively large.

3.The strapping pulleys and friction plates are loose.

4.The transmission belt is loose.

5.The suction of the electromagnetic clutch is not enough.

6.The connecting shaft of the upper and lower extensions is loose.

7.The lower extension is installed at an inclination.

It is estimated that the landlord has solved the problem, so he came to intervene and join in the fun.

Wuxi Huishan District original Hongjia hydraulic machinery manufacturing factory.

wxhongjia

Hydraulic baler.

There are several reasons for this.

First, there may be scratches on the pump disc of the oil pump.

Second, it may be that the pressure regulating part of the control valve is broken.

Third, it may be that the oil seal of the cylinder is aging, and it is time to change the oil seal.

Basically, there are a few reasons.

That's because the pressure of the hydraulic press is not enough.

Your fault description is too concise.

Because the cylinder action is slow, the insufficient flow should be considered, and the valve or cylinder diarrhea should be considered first, which may be caused by the wear of the valve core or the valve core being stuck. The cylinder should be inspected for damage to the seal. In addition, consider the failure of the regulating mechanism of the flow control valve.

Then consider whether the oil pump is damaged, or if the air is sucked in. The pressure cause can be checked first to see if there is enough hydraulic oil.

Structural composition. It is composed of the main frame system, hydraulic system, and auxiliary components.

Host frame system: high-quality thickened steel plate gas-welded casting sturdy frame Advanced mechanical design makes the equipment durable.

Hydraulic system: key components such as hydraulic pumps, solenoid valves and hydraulic cylinder oil seals use imported accessories, which make the packing pressure high, fast, durable and low-noise.

Electronic control system (optional): original domestic electrical control, travel switch, button, to ensure quality.

The inspection ideas are as follows: First, check the oil volume in the fuel tank to ensure that the oil volume is sufficient.

2. Check whether the motor steering is consistent with the direction of the oil pump.

3. Check the pressure regulating valve on the reversing valve.

4. Check whether the oil circuit is clean and clean the oil circuit.

5. Check whether the cylinder sealing ring is in good condition.

The reason for the pressure can be checked first to see if there is enough hydraulic oil, and then look at what is the pressure of the pressure valve? Generally around 20.

Check if there is less hydraulic oil, oil seals, valves.

Check to see if there is less hydraulic oil.

Hello, the reason why the hydraulic baler has no pressure: 1. Check whether there is a problem with the oil pumpFirst of all, we have to check whether the oil pump of the hydraulic baler is working normally, whether there is any abnormal noise, if there is an abnormal sound, it means that the oil pump has a problem; If it is normal, continue to check whether the master cylinder reversing valve is normal. Second, check whether there is a problem with the cylinder to see if there is a problem with the cylinder itself, if the lever range of the spare parts exceeds the original hydraulic cylinder, the control is not good, you can add a cushion block to the piston in the cylinder under the condition that the external size remains unchanged, adjust the pressure of the relief valve, adjust the pressure to 20mpa, pay attention to whether the oil gauge has changed or not, do not overpressurize.

2. Check whether the sealing ring is intact The inlet and outlet of the hydraulic baler should be well sealed, and no air should leak or enter the air. Then check whether there is oil leakage at the connection of the lower oil pipe, the inspection method is to dismantle the lower cavity oil pipe, take a bucket to catch the oil pipe, and press down to see if the lower cavity is very oily, if there is oil, the sealing ring is broken, if the sealing ring is broken, remove the pipe, and replace it with a 0-ring ring. 3. Check whether the pressure source has pressureCheck whether the pressure source of the door opening cylinder has pressure, and then see if the solenoid valve is electrified, if it is electrified, it may be that there is a problem with the overflow valve or the pump, if it is not electrified, it may be the cause of the electrical part, and check whether the intermediate relay or wire has bent off.

Also check whether the motor power is insufficient, which will cause the speed to be too low. Fourth, check the quality of the hydraulic oil but also check whether the quality of the hydraulic oil of the hydraulic baler is qualified, if it is unqualified, it will not only pollute the environment, but also block the oil filter, which will cause the liquid flow channel to be too small and the oil viscosity is too high, so that the oil can not be absorbed. I hope my reply can help you, if you have any follow-up questions, please feel free to ask me, I will reply to your <> as soon as possible

Summary. Hello dear, glad to answer for you.

The baler is pressed down strongly, and it can't be lifted up.

A1: Maybe the pump disc of the oil pump is scratched, 2: It may be that the pressure regulating part of the control valve is broken, 3:

It may be that the oil seal of the oil cylinder is aging, and it is time to change the oil seal. The baler, also known as the strapping machine, taping machine or strapping machine, uses strapping to bundle products or packs, and then tightens and combines the two ends by hot melt bonding with a hot hot iron. The function of the baler is to strengthen the packaging items, so that the items will not be scattered due to poor bundling during handling and storage, and they should also be bundled neatly and beautifully.

The baler is pressed down strongly, and it can't be lifted up.

Dear, hello, I'm glad to answer for you What is going on when the baler is pressed down with chain socks, and it can't be lifted up Answer1: Maybe the pump disc of the oil pump is scratched, 2: It may be that the pressure regulating parts of the control valve are broken, 3:

It may be that the oil seal of the oil cylinder is aging, and it is time to change the oil seal. The baler, also known as the strapping machine, taping machine or strapping machine, uses strapping to bundle products or packs, and then tightens and combines the two ends by hot melt bonding front by heating iron. The function of the baler is to strengthen the packaging items, so that the items will not be scattered due to poor bundling during handling and storage, and they should also be bundled neatly and beautifully.

Dear, if my answer is helpful to you, please also give a thumbs up (comment in the lower left corner), look forward to your like, your efforts are very important to me, and your support is also the driving force for my progress. If you feel that my answer is still satisfactory, you can close the void reed and click on my avatar for one-on-one consultation. Finally, I wish you good health and a good mood!

The baler is pressed down strongly, and it can't be lifted up.

1: There may be scratches on the pump disc of the oil pump, 2: It may be that the pressure regulating parts of the control valve are broken, 3:

It may be that the oil seal of the oil cylinder is aging, and it is time to change the oil seal. The baler, also known as the strapping machine, taping machine or strapping machine, is to use the strapping belt to bundle products or packages, and then tighten and close the two fighting ends through hot melt bonding of the hot hot iron. The function of the baler is to strengthen the packaging of the goods, so that the items will not be scattered due to poor bundling during the handling process and storage, and the strapping should be neat and beautiful.