TP LINK TL WR800N 300M VS TP LINK TL WR710N 150M THAT ONE IS EASY TO USE UNDER THE EXPLANATION WHAT

I also touched the problem of the landlord, and it was solved later.

There should be no problem with your settings, the key is that "TL-WR710N 150M this garbage thing" should be set by wired connection, remember to unplug the network cable between the connection Moden (cat) and the router WAN port before setting, otherwise IE cannot be opened with a wired connection (the management interface or settings cannot take effect, this is the key to setting that thing!! But the manual doesn't tell you! In addition, if the computer with the wireless router has a wireless network card (such as a notebook), the wireless network card should be turned off to avoid the mutual influence of the wired and wireless network cards, and the rest should be done according to the manual.

Note: If it doesn't work, you need to check the WAN port connection type and dialing mode, use IE to open the wireless router management interface as before, click "Network Parameters" on the left side of the interface to enter the WAN port setting column, and check whether the WAN port connection type and dialing mode are in line with your Internet access mode (i.e., PPPoE dynamic IP static IP).

Give it a try.

You use a route, there is no dialing function, you have to use the original cat to dial the number and then connect the router, the route settings are generally installed in accordance with the installation wizard, and everything else should not be changed at will. The status you are describing now is obviously that the dial-up was unsuccessful and the network was not available.

This is a mini wireless router with not very much network coverage.

First of all, log in to the router to set up the router, the method is to plug the network cable connected by the broadband cat into the router WAN port, turn on the power of the cat and the router, open the browser, and enter the router IP address 192,The screen displays the login router dialog box, enter the login name and password, the new router username and password are generally admin, OK, click the setup wizard displayed on the left side of the router interface, next, select adsl pppoe next, enter the username and password of the stand-alone Internet access, the next step, at this time, the screen prompts you to congratulate you on the Internet, according to the router model, the prompt method is also different, turn on the wireless Internet function in the wireless network parameters, the router is set up, you can go online, FYI.

The 740 is small in size and is easy to carry, and of course, there will be fewer Lan ports. The 841 is a domestic type with 2 antennas, and the 740 has only one. , 300m is definitely transmitting farther than 150m. The price of 841 is definitely more expensive than 740.

1. L-WR740N is a 150M wireless broadband router with 11N wireless technology and 150Mbps wireless rate.

CCA technology, improve wireless stability, expand wireless coverage, QSS fast security settings, wireless network security, set up faster IP bandwidth control function, free allocation of intranet user bandwidth.

WDS wireless bridging function for easy wireless network expansion.

2. -WR841N is an 11N wireless broadband router.

11N wireless technology, 300Mbps wireless rate.

2x2MIMO architecture, CCA technology, improve wireless stability, expand wireless coverage, QSS fast security settings, more secure wireless networks, set faster IP bandwidth control functions, and freely allocate intranet user bandwidth.

WDS wireless bridging function for easy wireless network expansion.

Parental control function to flexibly control the online behavior of children or employees.

The key depends on how many m of network cable you have. I feel the same for you, it is impossible for your home to install a network cable of more than 150m.

For one floor, 150m is enough. If you're 300m, you have to have a 300m wireless card, so there's no need for that, right? My house is 300 square meters, and I use the first one.

There is also the possibility that when the TL-WR700N sets the encryption mode, some mobile phones are not compatible with WiFi, you can try to change the encryption mode!

It's you who set the problem, just read the manual and follow the settings.

TP-Link TL-WR740N 150M can of course be connected to fiber broadband.

1. After the optical fiber enters the home, the pigtail is connected to the optical port of the optical modem;

2. The optical modem leads out the WAN port of the network cable and connects to the router;

3. The LAN port of the router leads out of the network cable and connects to each Internet device;

4. The wireless Internet access equipment is connected to the optical fiber network through the wireless signal of wireless routing.

I don't know, don't answer nonsense Optical brazing into the home is the standard configuration in the future Every family can use optical brazing to access the Internet After entering the house, you have to install a light cat They sent the optical cat out of the network cable In the 740 wireless router that is connected to you This router is a 150m wired and wireless dual-purpose Oh Changing the optical drill is just changing the cat and the home line Entering the home becomes a light brazing The cat is replaced by the optical cat The router is used.

Oh, don't be fooled, the broadband used by the general family is to use the ** online network.

That is, ADSL Internet access, to use the "cat", the router is connected to the "cat".

If you are traveling for business, then this is very good, and there is no problem of insufficient effective distance, because the hotel room is so big.

If you're at home, what's the point of buying a portable router? Heat dissipation problems, battery life problems, etc., will make people unhappy.

The issue of heat dissipation is a problem on any mini-type electronic device, and they don't take it into account, if you're at home, it's hot, it can't be left on 24 hours, it needs to be recharged.

Its small size is for easy portability, not to look good at home and not take up space ......You know, things that are too thin and too small usually don't last long hahahahaha

I'm using a 710n and haven't found the problem yet. This one with a plug does not involve battery life. The speed was not bad.

Want to know what? It's easy to use when it's set up, and the quality can be said to be fine.

The TL-WR700N supports five working modes: AP, Client, Repeater, Bridge, and Router.

If you use the TL-WR700N to set the BRIDGE mode, you can also extend the wireless coverage, first establish a wireless connection with the main AP, and then the TL-WR700N sends its own wireless signal for the client to connect, as shown in the following figure:

A wireless card is a wireless device in your laptop that connects to the router's wireless signal. You can't connect to a wireless signal without a wireless card. It's like two phones have Bluetooth, if one phone doesn't have Bluetooth, you can't use Bluetooth as a wireless device to receive songs from another phone with Bluetooth.

First you have to use your wireless router to dial up the Internet, and then there is a wireless computer icon at the bottom right foot of your laptop, you click to collect the wireless signal of your router, and then find it, click to connect.

Because, it is true that you are broadband, but your broadband needs a dial-up connection! What is the role of the router, which is to replace the broadband connection program on the computer to dial up. Can you still have a network port on the router when you connect the main line?

How can you receive a router signal without a wireless network card? Think about it yourself.

I went in.,Started to go in all the time.,Later, I found out that after connecting to the WR700N.,The assigned IP is.,So I tried it".,And then went in.,But when I saw the management interface.,I suddenly had a pain.。。。 The management interface is "dlink",There is an option to set a wireless password,But after setting the password,It's useless at all.,Just get a device over,Connect directly after you find it.,No need to enter any password。 I don't understand why.

Set the First time you want to connect with a wire setting.