How does the computerized pipe cutting machine work

The length of the middle section is fixed, the length is set in the PLC, and the servo is given a command, and after the servo receives the instruction, it drives the cutter to cut the ring according to the set length.

The microcomputer controls the rotation angle of the stepper motor or servo motor shaft, and the proportion of the feeding wheel corresponding to it calculates the size we want to cut, and gives a signal to cut the material to be cut through the cutting device, which is usually realized by the motor cylinder. Ruiyang Automation** has a variety of pipe cutting machines, you can take a look at their working principle.

Hello, if the automatic computerized pipe cutting machine continues to cut your material, you first have to see what material you want to cut, if you use the automatic computer pipe cutting machine to cut the heat shrinkable tube, it should be cut with the upper and lower knives, then you can choose to adjust the four screws in front of the machine, and there is no problem if you tighten them slightly. If you use a fully automatic computerized pipe cutting machine to make a silicone pipe cutting machine, you will use a single knife. In this case, you can try to adjust the white pad of the silicone tube cutting machine and make it a little higher.

We were also looking for such a pipe cutting machine before, after all, it costs a lot to buy a heat shrinkable pipe cutting machine and a PVC pipe cutting machine. When you can save money, try to save as much as possible. Therefore, when we purchase a pipe cutting machine, we look for a pipe cutting machine that can cut silicone pipes and PVC pipes at the same time.

I searched for a long time in Shenzhen, Guangdong to find it, and it can be said that it took all the effort to break through the iron shoes and find nowhere to go. Why do you say that, because the heat shrinkable tube cutting machine and the silicone tube cutting machine can actually use the same machine.

The main thing is to communicate more with the pipe cutting machine. There are a lot of people here in Shenzhen who do this heat shrinkable tube cutting machine, I can take a look at the general place.

This machine is suitable for cutting hook and loop cracked tape, cotton yarn tape, elastic band, plastic tape, zipper, PVC casing, heat shrinkable casing, fiberglass pipe, Teflon casing, row wire, small wire, conductive cloth foam, battery bridge separator, nickel sheet, diffusion sheet, reflective film, double-sided tape, Mylar, insulating paper, PE, copper aluminum foil, cable, release paper, etc.

Warranty period: The special computerized pipe cutting machine motion control system independently developed by our company is suitable for fixed-length cutting and <> of equipment in various industries

The automatic pipe cutting machine is specially designed to meet the needs of high-precision fixed-length cutting, and the changing cutting tool can cut various soft and hard materials such as plastic pipes, rubber pipes, composite pipes, copper pipes, aluminum pipes, etc. Pipe cutting diameter 10-25mm, pipe cutting length: Hengqin, pipe cutting accuracy:

。The speed of the cutting line is stepless in the range of 1-150m per minute. The pipe writing and cutting machine has the functions of fixed-length cutting of plastic pipes, the setting of yield and shift output, and the automatic alarm after the automatic counting reaches the set output value.

The touch screen allows users to set the cutting length of plastic pipes, set yields and shifts, change between automatic and manual pipe cutting methods, and restore the cutter position.

The computerized pipe cutting machine adopts a microcomputer numerical control display device, the length and quantity of the cutting belt, the feeding speed is set freely, and the adjustable roller feeding mechanism is installed, and the pressure and lifting are automatically adjusted on both sides, which can be quickly discharged, and the thimble feeding mechanism can effectively prevent the material from scratching, and is mainly suitable for high-speed cold and hot full half-cut cutting of strips. High precision, less loss, model design in line with ergonomic principles, simple operation and high automation.

High-speed feeding, the cutter speed is adjustable, the length of 50mm is set, and it can be cut about 120-150 times per minute.

Full Chinese LCD Lingyu display.

The length and speed are arbitrarily and continuously adjustable.

High-power feeding motor feeding, micro-electric pontine program control accuracy up to batch pause and delay time can be set.

Automatic shutdown due to lack of material. Save time and effort.