What is the process of downshifting a manual transmission car?

To sum up, there are two methods: 1. Simple deceleration and downshifting. Step on the brakes, step on the clutch when idling, downshift, continue to brake and slow down, and lift the clutch until the idle speed corresponds to the new gear ratio.

Driving school law. It is not recommended to cut off the power for a long time when actually driving, so there is a downshift to replenish the fuel. There are two ways to operate downshift refueling.

2. Downshift with oil replenishment. This is the most common in actual driving. Experienced manual drivers, especially those who usually drive sports cars and are more aggressive, often hear the engine snort when braking at intersections.

Although the speed is decreasing, you need to press the throttle. This is the more common method of downshifting. And whether it is decelerating, or overtaking in order to downshift and increase the speed, it is the same principle, the difference is that the speed, speed and gear timing will be matched with the actual driving.

The general sequence of operation is (brake not brake at will, depending on the situation) - step on the clutch - downshift - make up a foot of oil, how much the speed is increased depends on the actual situation, the matching of speed, gear and speed, drive more naturally feel - lift the clutch. This will significantly reduce the frustration of downshifting for many novices. There are some differences in the timing of the throttle.

Mainly when decelerating. General road driving, there is enough time for the driver to move from the brake to the throttle to continue to downshift and continue to brake, and some drivers drive more **, or when going off the track, they will not release the brake when downshifting and stepping on the clutch to replenish the oil, and the right toe point brake heel point brake oil, this is the so-called heel toe, in fact, as far as I feel, it is also meaningful to practice good heel toe when driving on the street. For example, when following the car to slow down, if the oil is replenished separately, the time when the right foot leaves the brake is a safety hazard, once the car in front brakes sharply at this time, it will be too late to react, and the heel toe can ensure that the brakes can be stepped on at any time.

However, practicing heel is not a day's work, and practicing it well is very beneficial. In my feeling, after practicing the heel toe, driving MT into the realm of the integration of people and vehicles is considered an entry. <

After the car reaches a certain speed (it is recommended to switch gears in 2000 3000 at ordinary times), step on the clutch, step on the low (otherwise the clutch and gearbox are very hurt), step on the low and push the gear into the next gear, do not jump gear, it is not good for the engine, and it is easy to stall.

The correct way to operate manual downshift is to:

1. Put the gear into neutral gear at the starting stage, step on the clutch, turn on the ignition switch, cut into the first gear, slowly release the clutch, cooperate with the throttle, and start the car;

2. After the car starts during the acceleration process, as the engine speed increases, it cuts into the corresponding gear with different speeds;

3. Easy drivingEven if you are a novice, you can let your left foot temporarily relax and move away from the clutch position;

4. Precautions Normally, when the speed is increased to a certain extent, the engine will have an abnormal sound, and it must be put into gear at this time;

5. It is easy to operate and shift gears without much effort, if the model is older, you can stay in neutral for a while, and then cut into other gears;

6. When controlling the clutch to shift gears in the car, the clutch pedal should be quickly pressed and lifted, and the half-engagement phenomenon should not occur, so as to achieve "fast-slow-fast";

7. The principle of deceleration and gear shift is the same, but it should be noted that when the speed is too fast, the speed should be reduced to the corresponding range first, and then the gear shift should be carried out.

Hello, the manual transmission Jiangsu method first step on the brakes, let the speed down, and then press the clutch. Switch to low gear and release the clutch, I hope my answer is helpful to you, I hope to adopt, thank you.

Manual transmission car, the right way to slow down!

<> "Driving a vehicle with a manual transmission requires the driver to manually change gears when changing gears. So what's the right way to downshift a manual transmission?

When the car is in motion, the first thing to do is to make sure that the vehicle remains stable and avoid downshifting when cornering or ramps.

Then, before downshifting, it is necessary to reduce the speed first, so that after downshifting, you can avoid the phenomenon of acceleration weakness and setback.

Press the clutch all the way down, release the throttle at the same time, and then hook the shift lever into the corresponding gear or ride.

After completing the gear, the clutch should be lifted to the state of semi-linkage, when the output power of the car and the power transmission device are connected smoothly, gently step on the accelerator to give oil, and finally slowly release the clutch.

The correct manual transmission downshift technology can give the car more power at low speeds, and also help to reduce the fuel consumption of the cracked beam car and improve the driving safety. Therefore, learning the correct downshift technique is a very important skill for car drivers.

1. The clutch pedal must be pressed to the end before shifting, and the operation of the gear lever should be brisk, soft and accurate.

2. Pay attention to the choice of the rubber machine when shifting gears, and when reducing gears, when the speed drops to a certain value, you can hang into the low-speed gear.

In the case of ensuring safety and good road conditions, the high-speed gear suitable for the speed should be used as much as possible to reduce the wear and tear of the parts and reduce fuel consumption, and adjust the speed of the vehicle in time according to the road surface and traffic conditions.

It should be noted that it is not possible to go low and high, and the knocking caused by towing will have an adverse impact on the engine and gearbox.

3. Be sure to hang down the Antchang block after the car stops steadily; Similarly, to make the vehicle move forward after reversing, the car should also be parked before engaging the forward gear. Otherwise, there will be a loud snorting sound.

4. When driving, putting your hand on the gear lever for a long time will cause premature wear of the transmission shift fork. So after changing gears, the right hand should be off the gear lever.

Manual gear downshift operation, mainly to slow down first, and then step on the clutch to hook into the gear you want to hang into, according to the different gears, the speed of the clutch is different, the manual transmission car can be overturned when downshifting, as long as the clutch is well matched, the basic pants cavity of the car has no frustration.

Manual transmission car downshift, first have to slow down, deceleration has to step on the brakes, for example, you are driving on the high-speed cover, you use five gears, now the speed is about 100 kilometers away, you have to downshift to four gears, then your first step is to slow down, the speed down after the specific speed test their own mastery, the highway can not drop too much about 70-75, step on the clutch to hang into neutral, stay for two seconds, and then hang into the fourth gear, directly and slowly release the clutch on the line.

If it is low-speed driving, the third gear is lowered to the second gear, this is simpler, decelerate directly, do not slow down to can, directly step on the clutch, push into neutral gear for two to three seconds and then push into the second room, slowly lift the clutch, the clutch can not be lifted too fast, and the car will rush and frustrate if it is too fast.

Downshift deceleration is not commonly used and is generally applied in the following situations. First, when going down a long slope, only using the brake is easy to cause the brake pads to fail over the brake, so it is recommended that Hongxing use downshift to decelerate, and use engine braking to control the speed of the vehicle more safely. Second, through the curve with a gentle angle, you can not brake, decelerate by lowering the gear, and directly refuel and speed up in the current gear after cornering, so that the cornering is faster and more convenient.

Photo by Zhang Guiye) NIO ES8 NIO ES6 Wenjie M5 NIO EC6 Xpeng P7 Trumpchi GS8 @2019