How do you disassemble the lid of a Midea rice cooker? How to remove the Midea rice cooker lid

1. To remove the lid of the Midea rice cooker, you need to prepare the following tools: a Phillips screwdriver.

Slotted screwdrivers, self-tapping screws.

2. Next, use a flathead screwdriver to pry open the lid handle of the Midea rice cooker, and use a Phillips screwdriver to unscrew the screws in the handle and remove the handle first, as shown in the figure below.

3. Next, you need to open the lid of the Midea rice cooker, there are two screw holes sealed with rubber in the rotating position of the lid, and use the prepared thin self-tapping screw tool to take out the rubber, as shown in the figure below.

4. Then use a Phillips screwdriver to unscrew the two screws, and remove one of the screws at the exhaust hole on the lid to disassemble the panel of the lid, as shown in the figure below.

5. Next, after opening the lid panel of the Midea rice cooker, remove the connecting rod inside and the pressure sealing ring in the lid, and then remove the lid lock ring, as shown in the figure below.

7. Finally, the lid of the Midea rice cooker was disassembled, as shown in the picture below.

2. You can clearly see the inner lid (silver) of the Midea rice cooker lid, and there are two buckles on both sides of the inner cover, which are the switches to open the inner cover.

4. Finally, you can remove the inner cover for cleaning, after washing, when installing the inner cover, put the inner cover in line with the center point, and then press the buckles on both sides back, and the installation is completed when you hear a click.

The lid of a rice cooker can be disassembled, that is, the white silica gel in the middle, hold the aluminum sheet on the inside with your hand and pull it down, wipe it with a scouring pad dipped in some dish soap, and finally rinse it thoroughly with water, because the dish soap has a peculiar smell at high temperatures, which affects the taste of your rice and your health, and the lid of some rice cookers is not detachable, that is because there is a silicone gasket around the aluminum sheet and between the plastic, which can also be cleaned by the above methods.

Three screws are attached underneath the nameplate paper.

The rice cooker does not need to be placed with the bottom facing up, just at the bottom edge of the side, as long as you uncover the nameplate paper and remove the screws, you can take off the base.

Take out the outer cover first, and then break the white plate of the inner lid to remove it. Here's how:

1. Close the lid of the rice cooker, then break the outside with your index finger up and press down with your thumb.

2. Remove the outer fixed cover, and then remove the inner cover.

3. You can see that the cover has been prompted to remove the cover, and disassemble it according to this method.

4. Grab the cover plate with one hand and push the white buckle upward.

5. Break the buckle with the other hand so that it can be removed.

The way to remove the Midea rice cooker lid may vary from model to model, the following are the steps to remove the Midea rice cooker lid under normal circumstances:

1. Make sure the rice cooker has been powered off and cooled. If the rice cooker has just been used, you will need to wait for it to cool down to room temperature before disassembling it.

2. Flip the rice cooker to the back and find the buckle under the lid. Some Midea rice cookers have a screw underneath the lid that you need to use a screwdriver to unscrew.

3. Use a tool (such as flat-nose pliers) to gently open the buckle. Be careful not to use too much force to avoid breaking the buckle.

4. Remove the lid. When the snap is opened, you can gently remove the cover.

5. Clean the lid. Before removing the lid, you can clean the lid to remove any remaining food or dirt.

6. Reinstall the cover. After cleaning the lid, you can reattach it to the rice cooker and secure it using snaps or screws.

It should be noted that different models of Midea rice cookers may have different disassembly methods, so it is recommended to check the instruction manual or consult after-sales service before disassembly. In addition, it is necessary to pay attention to safety when disassembling to avoid accidental injury.

<> To remove the Midea rice cooker lid, follow these steps: Self-ordering.

Make sure the rice cooker has been disconnected from the power supply and that there is no heat or steam generated inside. Wait for the rice cooker to cool completely.

Locate the fixture on the rice cooker lid, usually two or four screws or snaps. These fixtures may be located on either side or at all four corners of the lid.

Use an appropriate tool, such as a screwdriver or flat-edged screwdriver, to loosen the lid fixture by unscrewing the screws or pressing the clip.

Once the fixture is loose, you can gently lift or push the lid open to remove it from the main body of the rice cooker.

Please note that removing the rice cooker lid may vary depending on the model and design. It is best to refer to the rice cooker's user manual or the manufacturer's removal guide before proceeding with the disassembly to ensure proper operating procedures and safety precautions. If you are unsure how to proceed with the disassembly, it is advisable to consult the manufacturer or seek the help of a professional.

The removal method of Midea rice cooker lid may be slightly different depending on the model of rice cooker, here are some general operation steps for reference:

Pour out the meals from the rice cooker first, then unplug the cord and wait for the rice cooker to cool down to room temperature.

Pick up the rice cooker, flip it over so that its bottom is facing up, and find the screw or clip that fastens the lid.

Using a screwdriver or tool, loosen the screws or unfasten the clips and remove the fastening cap.

Place the fastening cover on a flat tabletop and use a screwdriver or tool to loosen the screws on the fastening cover or unfasten the buckle to remove the cover.

If the liner or other parts need to be cleaned or repaired, it can be operated as needed, and after the operation is completed, the installation and assembly can be carried out according to the reverse steps.

It should be noted that when disassembling and repairing the rice cooker, it is important to pay attention to safety and do not touch the power cord and power plug of the rice cooker to avoid electric shock. Additionally, if you are new to the disassembly and repair of rice cookers, it is advisable to seek professional help.

First, make sure that the rice cooker has been de-energized and completely cooled. Next, you can remove the lid of your Midea rice cooker by following these steps:

1.Carefully inspect the perimeter of the lid to see if there is any wear or damage. If there are any problems, they should be repaired or replaced as soon as possible.

2.Remove the liner from the cooked staple food so that the outside can be cleaned and maintained.

3.Follow the instructions and separate the pot from the lid.

4.Leave the lid perpendicular to the rice cooker housing for easy access to most surfaces on the bottom of the lid.

5.To determine if there are any fixing points on the lid, you need to unlock it with a tool. There may be clips, screws, small buckles, etc. on the lid, depending on different models.

6.When removing the various parts of the pot lid, pay attention to gentle disassembly to avoid damage to the rice cooker.

1. Align the raised position on the rice cooker with the notch, then turn the handle to a specific position, and then turn it to remove it.

2. Turn the rice cooker upside down, remove the screws at the bottom, and remove the power socket shell.

3. Remove the screws under the lid on the back of the rice cooker.

4. At this time, the whole rice cooker is very loose, you can lift the bottom shell of the rice cooker head, separate it from the whole body, and then turn it upside down to separate it from the bottom shell. At this point, the entire rice cooker has been disassembled.

How to disassemble the lid of the Midea rice cooker: 1. Open the lid of the rice cooker, and then you can see the buckle on the inner lid. 2. Press the buckle hard, and then you can open the inner cover.

3. Above the outer cover, there is the outlet of the rice cooker, you only need to squeeze hard at the gap to take out the exhaust hole, and then rotate it to the left to open it. A rice cooker is a cookware that converts electrical energy into heat energy, which is fully functional, easy to use, and relatively safe. When buying a rice cooker, try to buy products from big brands, and when choosing a rice cooker, try to buy fully functional equipment.

When purchasing, consult the material of the rice cooker liner, do not have the liner with harmful substances, check whether there are traces of damage, and the power cord and plug can be used normally. Tips for using the rice cooker: When using the rice cooker to cook rice, the button will automatically turn on after cooking, wait for the heat to dissipate for a period of time before turning it on, generally about ten minutes, and the rice can be cooked thoroughly.

It is not advisable to use a rice cooker to boil water, because it consumes electricity and takes longer, try to cook the rice before the peak electricity consumption period, and place it in a state of insulation to prevent the electricity consumption from tripping. For more information about how to remove the lid of the Midea rice cooker, enter to see more content.

There are two Phillips screws under the side tab, unscrew the one on the left. (The other is a bolt, which should be for the grounding wire.) Ignore it)

Pry it open with a slotted screwdriver along the gap, it is jammed with a card slot. Both the bottom and top slots are sub-slotted. (If the rice cooker has been used for a long time, it may not be easy to open.)

Midea rice cooker consists of two layers, the inner pot is used to hold the food that needs to be cooked, and the outer pot plays the role of safety protection and heat preservation. Between the inner and outer pots, there can be an air interlayer, or it can be filled with insulation. The electric heating element is generally placed in the aluminum heating plate, and the heat emitted by it is evenly heated at the bottom of the cooker through the heating plate.

The temperature control device is generally composed of two parts: a thermostat and a thermostat, the thermostat ensures that the temperature in the pot will not exceed a certain value, and it is installed in the cavity in the center of the heating plate; The thermostat ensures that the temperature of the food in the pot is kept at 60 80 after cooking, and it is installed elsewhere under the heating plate.

In order to ensure the normal operation of the rice cooker, please do not disassemble the machine, if there is a failure, please send it to a professional after-sales service.

Plug in the power supply and trip should be the safety is broken or the wire is burned out, the base is buckled, the hard pry is easy to break, go to the place where the electrical appliance is repaired and let him open it.

1.Remove the bottommost screw.

2.Use a flathead screwdriver to pry open the rice cooker chassis and upper part.

3.After separation, remove the fixing screws in the heating plate and the inner tank wall, and take out the heating plate.

Introduction: Rice cooker, also known as electric cooker, rice cooker. It is a cookware that uses electrical energy to convert into internal energy, which is easy to use, clean and hygienic, and also has a variety of operation functions such as steaming, boiling, stewing, and simmering food.

Common rice cookers are divided into three categories: automatic heat preservation, timed heat preservation and new microcomputer control. Now that it has become an everyday household appliance, the invention of the rice cooker has reduced the amount of time many families spend cooking rice.

Structure: Ordinary rice cookers are mainly composed of heating plate, temperature limiter, insulation switch, lever switch, current limiting resistor, indicator light, socket, etc.

How to remove the lid of the Midea rice cooker.

1. Since the connection used in most Midea rice cookers is not removable, we can remove the metal part in the upper lid and clean the gasket of the inner lid;

2. There are two buckles under the inner cover, you can press the middle button to the center of the inner cover by hand, you can take it out, you can clean the inner cover with water, scrub it clean and then install it back;

3. The inner cover gasket cannot be removed, it is difficult to install it back, it is recommended to simply clean it with a rag;

4. In addition to the inner cover, you can also remove the exhaust hole on the outside of the upper cover, different Midea rice cookers have different ways to remove them, you can grab the lid and break it up, and then unscrew the exhaust cover according to the above marking, rinse it directly with clean water and then install it back;

How to disassemble Midea's rice cooker.

1. Turn the handle of the rice cooker to a specific position and then remove it, the raised place on the rice cooker must be aligned with the notch before it can be removed. 2. Turn the rice cooker upside down and remove the 6 screws at the bottom of it and the socket shell of the power supply.

3. Remove the screws on the back of the rice cooker and under the rotation of the lid.

4. Lift the head and bottom shell of the rice cooker and separate it from the body a little, and then turn the rice cooker upside down to separate the bottom shell of the rice cooker.

The sealing ring on the lid is soft jujube ear plastic, under normal circumstances, the edge of the lid will be buried in a circle of grooves, put the sealing ring flat by hand, against the edge of the groove, and press it in a little bit in a clockwise direction.

Below is the installation of a rice cooker's sealing ring**:

<> the third picture is the most difficult and critical part, the lid has a total of six bayonets, the upper two don't pry the family pat, just pry open the four on both sides, and then lift it up to come out. Be careful not to use too much force when prying the bayonet, and the gap can be padded with a thick piece of paper to avoid covering the shell**. In the fourth figure, when the aluminum sheet is returned, it should be in the same direction as the original, because it is easy to break in the opposite direction.

The small aluminum sheet with round holes in the fifth figure is positioned, and it is enough to align this when installing.