Manual transmission car driving knowledge and skills

The first gear is the starting gear, as the name suggests, it is the gear used at the beginning of the car from stopping to starting to drive, and the other layer of the starting gear is just starting to use, once the car starts to run, it needs to change the gear to the second gear.

The second gear is the driving gear, and similarly, it refers to the gear where the car is driving in a vulgar manner, which means that as long as the car is moving, at a very low speed, and there is no stop, you can take this gear, not when driving at high speed. In addition, some vehicles with a large idle speed can even use the second or third gear to start with the accelerator, which is not recommended here.

The third gear is the acceleration gear, that is, from this gear onwards, you can accelerate with the throttle, so that the speed of the car can be increased to a certain extent.

The fourth gear is the medium and high-speed driving gear, basically in the city road, except for the elevated road section can only be used at the highest level, according to different vehicles, the speed is generally maintained at about forty to fifty when used.

The fifth gear is a high-speed gear, basically only viaducts, highways, etc. need to be used, and the general speed is used at 80 or above.

The manual transmission car, the most critical, is also a little difficult to master, is the clutch junction point, if you can master the clutch junction point, is the clutch semi-linkage state, the rest are easy to do.

Obeying the traffic rules is the greatest security.

There is no skill in manual transmission, as long as you touch the multi-gear familiar, there is no problem.

<><1.Adjust the seat and steering wheel: The seat should be adjusted to the appropriate position so that the foot can easily step on the clutch and brakes; The steering wheel should be adjusted to the right angle for the sock, so that the arms are naturally bent when holding the steering wheel.

2.Familiarize yourself with the clutch: The clutch is a key part of driving a manual transmission car, and you need to be familiar with how to use it.

When the clutch is depressed, the transmission between the engine and the transmission is disconnected, and the gear can be changed or stopped. When the clutch is released, the transmission between the engine and the transmission is connected, and the car starts moving.

3.Adapting to the start: When starting, you need to press the clutch first, then press the throttle, and at the same time slowly lift the clutch to make the car start slowly. Be especially careful when starting and don't turn off or jump out of the lane.

Next, let's introduce the gear shift technique:

1.Choose the right gear: In normal driving, you should choose the right gear according to the change of vehicle speed and rpm. In general, low gears (1st, 2nd, 3rd) are used for starting and climbing, and high-speed gears (4th and 5th) are used for driving on the highway.

Manual transmission driving techniques and methods are as follows:

1. Some people look at the engine speed shift, some people look at the speed shift, both of which are okay, but you have to find the best time to shift gears. If you want to drive gently, you can change gears earlier, and if you drive harder, the power is better, and you can postpone the gear shift. There are minimum requirements for shifting, that is, the power of the engine must be able to play out, it cannot be said that after changing the upper gear, the engine power is very weak, the speed of stepping on the accelerator is very slow, and the speed of the car has not changed much, which belongs to premature gear shifting.

2. After hanging on the high gear, the engine speed can respond quickly when stepping on the accelerator, and the speed of the vehicle should be significantly improved, and the general engine speed of 2000 rpm is more reasonable, and the power is relatively strong, and the minimum can not be lower than 1700 conversion gear.

3. Downshift when overtaking or insufficient power. Because the power of the gearbox comes from the engine, the power of the engine must be brought into play, and the gearbox can get better power. The gear is high, the engine needs a lot of force to drive, because the engine power is limited, so when the engine needs to rotate quickly in the high gear, its responsiveness will become poor, and it will not rotate.

4. The engine will be used to brake when going down a large slope or parking. Down a relatively long or relatively large slope, such as entering the underground garage, a few kilometers of high speed downhill, should be hung into a low-speed gear, the use of the engine's anti-drag brake to control the speed, should not rely on brake control.

5. When entering the underground garage, you should hang into first gear, release the clutch completely, and then use the brake to control the speed. When you reach the bottom of the slope, be ready to step on the clutch at any time in case the flame goes out. You can't put it in neutral gear or hang it in first gear and step on the clutch, just use the brake to control the speed.

When parking on the ramp, the handbrake should be put into another gear after turning off, which also uses the running resistance of the engine to help braking and improve safety.

Driving a car with a manual transmission should be accurately geared according to the speed of the car, otherwise the car's gearbox will be damaged. There are a total of five gears in the car with a manual transmission, and there is also a reverse gear, with the first row showing the r and the second row showing .

In the process of driving a car, the gear meshing device in the transmission of the car can be changed by turning the gear lever by hand, so as to change the transmission ratio of the car, so that the car can achieve the purpose of shifting.

Requirements for matching gear and vehicle speed: 1st gear: This gear is used when starting, or when climbing, when using this gear, the engine speed is very high, and the torque is also very large, which can provide strong power for the car in an instant, using this gear, the speed is generally 10 kilometers per hour.

2nd gear: This gear is the transition gear of the car after starting, and the speed of the car is generally 20 kilometers per hour.

3rd gear: It is used at a general speed of 20 km/h to 40 km/h, and is often used when driving in urban areas.

4th gear: With this gear, the car travels at a speed of 40-60 km/h. Modular hail.

5th gear: At a speed of more than 60 kilometers per hour, you can use this gear for Dantanfan, and it is used more at high speeds.

Millions of car purchase subsidies.