The Toyota Ruizhi VSC light is on and does not catch fire

Hello, Ruizhi VSC light is lit, it is to detect that the side slip system is faulty, but you can't send it, the engine fault light will also be on, under normal circumstances, the VSC light is on, the engine fault point will also be lit, the battery voltage is not enough will also be lit, you now confirm the battery voltage. Then use the decoder to read the fault**. Specifically, look at the explanation of the fault **, so as to analyze the next solution.

Usually, this happens either because your car is flooded or because of the after-effects of a crash.

If you plan to continue opening.

Just go to the 4S shop and repair it seriously.

But it's estimated that it's not a lot.

Ruizhi is expensive to repair cars.

If it's not cost-effective.

Sell it, it's also a helpless move.

1、Open the driver's door of the FAW Toyota Ruizhi. 2. Pull the hood switch of FAW Toyota Ruizhi.

3. Lift the hood of the engine of FAW Toyota Ruizhi.

4. Slowly unscrew the lid of the small kettle of the water tank of FAW Toyota Ruizhi, and let go of the high-pressure gas inside the small kettle of FAW Toyota Ruizhi.

5. Fill the small kettle of FAW Toyota Ruizhi with cooling water to the max position.

1) "Vehicle" means motor vehicle and non-motor vehicle.

2) "Motor vehicle" refers to a wheeled vehicle that is driven or towed by a power unit and driven on the road for personnel or for transporting goods and carrying out special engineering operations.

3) "Non-motorized vehicles" refers to vehicles driven by human or animal power and driven on the road, as well as motorized wheelchairs for the disabled, electric bicycles and other vehicles that are driven by power units but have a design maximum speed, empty mass and external dimensions that meet the relevant national standards.

The Ruizhi VSC light is on, turn off the engine and restart to see if it is still on. If it doesn't light up, don't worry about it, just drive normally. If it is still bright, you can only go to a 4S shop or a professional auto repair shop, and let the technician check it first to determine where the problem is, so that the symptoms can be repaired.

Since you can't see the actual car, you can't make an accurate judgment. If there is a problem with any of the three components of the air intake system, fuel system, ignition system, the VSC light will be lit. Here are a few of the more common causes and solutions:

1. Oil problems. If you keep adding 95 oil and suddenly change it to 92, this phenomenon will occur. Solution: Add 95 gasoline.

2. Air filter problem. If the air cleaner is dirty and the air intake is not enough, it will give an alarm. Solution: Replace the air cleaner.

3. Problems with oxygen sensors.

4. Problems with spark plugs or ignition coils. Solution: Replace the spark plug or ignition coil.

Attached VSC Introduction:

VSC is the body stability control system, other manufacturers call ESP, VSC is Toyota's name. When this happens, it means that the car has a failure in anti-skidding, traction control, etc., and in extreme road conditions such as ice and snow roads, sideslipping may occur, and non-extreme road surfaces do not affect normal driving.

1.Make sure the vehicle has come to a stop and the parking brake pedal is released;

2.Start the engine;

3.Press the parking handbrake (and hold), lightly press the brake pedal twice, and then release the parking brake pedal;

4.Press the brake pedal (and hold), lightly press the handbrake pedal twice, and then release the brake pedal;

5.Press the parking handbrake (and hold), lightly press the brake pedal twice, and then release the parking brake pedal;

At this time, the VSC light and TRC light will turn on, indicating that the VSC system has been turned off.

You have 30 seconds to do the above steps each time you start the car, and it will return to its original state when the car is stopped and turned off.

The so-called light pedaling: just see the handbrake light on, no need to step deeply.

Look at the lower right of the steering wheel, whether it has touched the VSC button.

Hello, if the lights of this car are always on, it is recommended to go to 4S to check it to prevent accidents.

The focus is to see what the fault is**Need to use the diagnostic computer to enter the ABS system to see what the fault is**, or may it be due to engine failure The light is on? As a result, this fault light is lit, but also to see what is the fault in the engine**?

In this case, it is recommended that you go to the repair shop or 4S shop in time to find a professional computer and test it.

Hello, in this case, it is best to use the computer to read the fault code first, and check what the specific fault information is.

It's best to go to the 4S store to read a fault code to see what the problem is, it may be a problem with the line or the sensor.

Hello, this is a Nissan car body stability system failure.

VSC is the body stability control system, the fault light is on, which means that the car anti-skidding, traction control, etc. are faulty, and in extreme road conditions such as ice and snow roads, side slippage may occur, and non-extreme road surfaces do not affect normal driving. Such faults need to be detected with the help of a computer detector to check the body stability system.

Ruizhi VSC and engine fault light on, side slip light when the vehicle in the process of driving skidding, restore this state only need to turn off the engine restart, because the anti-skidding function is turned on by default when the vehicle starts, you can also press the off button when driving, to temporarily turn off the anti-skidding function, so that the fault light will be off, the specific operation steps are as follows:

1. Press the brake pedal of Ruizhi.

2. Press the one-key start button of Ruizhi.

3. Ruizhi's instrument lights up, and the power supply of the whole car is turned on.

4. Press the OFF button of Ruizhi to turn off the anti-slip mode.

5. At this time, Ruizhi may have the danger of sliding when driving on rainy and snowy roads.