Whether the wireless bridge can provide wifi directly to the mobile phone

You can use a wireless bridge for coverage, and the transmission distance and speed are related to the power of the router and whether there are obstructions, as long as there are not too many walls, and the network speed.

All of them can be used normally and can be set according to the following steps.

Tools: Computers, routers.

1. Enter the login address of the Mercury router in the address bar of your browser.

2. Enter the router management password to log in.

3. Click [Advanced Settings] in the upper right corner of the router management interface.

4. Click [Wireless Settings] in the toolbar on the left side of the interface.

5. Continue to click [WDS Wireless Bridge] under Wireless Settings.

6. Continue to [Next] at the bottom of the interface.

7. Select the router you want to connect to in the list.

8. Enter the connection password of the router, and click [Next] after entering.

9. Confirm whether the current information is correct, and then click Next.

10. If there is a conflict between the default IP address and the main route, change it and click [Next].

11. Finally, click [Done] and wait for the router to reboot to surf the Internet.

Yes, the wireless bridge is used for unlimited coverage! Estimate your range for one bridge is not enough! If you set up a bridge opposite the floor that needs to be covered with network cable PoE power supply, and transmit to the entire building of your company, it depends on the blocking situation, the effective coverage distance is from 3 to 500 meters, I have tested it with customers before, and the mobile phone can also receive, if it is an office computer with a wireless network card to access the Internet, then there is no problem.

The speed is based on your broadband!

The bridge is a private protocol, and the signal sent by the bridge can only be received by devices of the same brand and model. The device used for wifi coverage is called 'AP', and the signal sent by the AP can be recognized by the wireless network card. The effective distance covered by a good AP in an open area is about 800m, and it is better to penetrate walls than a router, depending on the equipment, but you don't expect to be able to penetrate several walls and have a good signal.

Even the mobile phone signal relies on the dense base station and the reflection of the signal to have the signal, not through the wall.

If possible, one can be installed on the roof of each building to provide wireless coverage of the building and surrounding areas. But the location of the installation is very important, which largely determines whether the signal is good or not. If you can, it is advisable to consult a professional, o(o haha

You can't use a wireless bridge, it's a docking network, and if you want to use it at every layer, you can buy a signal amplifier.

Bridges are not a direct substitute for wifi. The wireless bridge is to connect the original router wirelessly through the new router, and then transmit the wifi signal, and then connect the new wireless router with mobile phones and other devices, which can realize the role of wifi signal amplification.

As the name suggests, the wireless bridge is the bridging of the wireless network, which uses the wireless transmission mode to realize the bridge of communication between two or more networks, and the wireless bridge is divided into circuit bridge and data bridge from the communication mechanism. In addition to the basic characteristics of wired bridges, wireless bridges work in or frequency bands that do not require a wireless license, so they are more convenient to deploy than other wired network equipment.

The wireless bridge is evolved from the wireless network card, and its kernel itself has a wireless network card, which is used for the last segment of wireless transmission in network transmission or network bridging within a limited distance, also known as small microwave, and wireless is a small decoding plus transmitter, with the function of signal coverage.

To replace the network card with a wireless network bridge, you must first figure out the receiving distance of your wireless network card and the transmission distance of the wireless router, and the signal directionality of the wireless bridge is strong and easy to block.

All connected to the wireless router under the same wireless bridge, the computer can access the Internet, but the mobile phone cannot. Then you know wireless router bridgingThe solution to the phone can't access the Internet after the wireless router is bridgedWhether DHCP is enabled on the router and whether the signal of the router is stable is generally 25db or more.

Check whether route B is successfully bridged. Then connect the mobile phone to the wifi signal of the B router to see if there is a network, and enter the IP address of the B router in the view of the mobile phone.

Whether to go to the router settings interface, and then use the computer to connect to the wifi of the B router to see if there is a network Open the web page, if the computer has a network, but the mobile phone sometimes has a time to wait for the network, then look at the router's LAN port settings Whether it is the same as the LAN port setting of a router, (check that when you successfully bridge a router and directly enter the general router is this IP address, you will find that you enter a router and have a password to modify but still don't go to the router i of the house.) That's how I lost my reputation for the nearest wifi).

In the above steps, it is the easiest way to check the LAN port address, if you enter your router address and go into the router address of A, it means that your LAN port address is in conflict, why does the computer not affect I don't know It may be a problem with the mobile phone, the mobile phone vivoy13 is not affected My MX3 is affected, I am speechless, please see the figure, the last digit should be changed casually, as long as it is not duplicated with the LAN port address of the A router.

1.What should I do if the secondary router cannot access the Internet after bridging.

2.What to do if you can't access the Internet after the wireless router is bridged.

3.Router wireless bridging.

What to do if you can't get online.

4.What should I do if the TP router cannot be connected to the Internet after wireless bridging?

No, now let's explain what a bridge is

1. The traditional sense is not explained in detail, and it needs to be discussed at length, only explaining the currently commonly used network bridge, which works at the data link layer, and is generally a soft network bridge, that is, it is realized through software.

2. Explain the misunderstanding of why this is asked, the mobile phone wireless network card can be made into a wireless relay device, the relay is to extend the distance, increase the signal and other functions, the mobile phone is configured as a relay to allow other mobile phones or the wireless network card of the mobile phone to access the Internet.

Oh, I forgot, I studied the Internet, I don't know much about mobile phones, and suddenly it occurred to me that the mobile phone has a mobile phone card, which should be able to be tied into a bridge, and I don't know the specific implementation. Let's go down.

Workaround:

Check 1: Check the settings of the secondary router.

1. Shut down the DHCP server.

If DHCP is enabled on the secondary router, the computer may obtain the wrong gateway address and cannot access the Internet, so you need to shut down the DHCP server of the secondary router.

Setup method: Log in to the management interface of the secondary router, click DHCP Server >> DHCP service, select DHCP server as Inactive, and click Save.

2. Modify the IP address of the LAN port.

If the management IP address of the primary and secondary router is the same (for example), it will cause a conflict of IP addresses and cause the computer to be unable to access the Internet, so you need to change the management IP address of the secondary router.

Save. When the restart prompt page pops up, click OK and wait for the restart to complete.

Check 2: Check the settings of the primary router.

1. Firewall settings.

Please check whether the Internet access control is enabled on the main router to restrict the Internet access of the corresponding computer. It is recommended that you change the rules or disable the Internet access control for the time being. As shown in the figure below:

2. ARP binding.

The main router sets the IP and MAC address binding to prevent ARP spoofing, you can turn off the ARP binding and try to surf the Internet, Note: **The data provided is for reference only, mainly for practical applications.

Troubleshoot 3: Compatibility issues.

If the problem cannot be solved through the above troubleshooting, it may be caused by the compatibility of the router's wireless communication mechanism. You can try to use the wireless WDS of the main router to bridge the secondary router (the roles of the primary and secondary router are reversed) to test whether it can be used normally.