How to connect the cable under the rural outdoor wireless network bridge to the wireless router? 30

There are two cases:

The wireless bridge is connected to the WAN port of the wireless router under the wire

1. Then enter the router settings (usually entered in the browser, you can see the instructions on the reverse side of the router).

2. Select the dialing method in the WAN settings of the wireless router, usually PPPOE, and enter the username and password.

3. Then set the SSID, set the verification method and verification password.

The cable of the wireless bridge does not need to dial up the Internet, that is, you can access the Internet directly after connecting to the line, then the cable of the wireless bridge is connected to the LAN port of the router, and then repeat the above steps 1 and 3.

It's really not good to find a door-to-door help to repair the computer.,My family used it before.,It's because it's not good to make it after changing the community.,Later, my home is looking for a door-to-door computer repair person to install.。

Wireless bridging can also connect routers, it depends on whether your router supports wireless bridging, you must ask the merchant when buying a router.

There is no way to write detailed steps for this, I can only tell you the general idea, and you have to do it yourself. Hope it helps.

It is best to use the same type of wireless router or AP of the same manufacturer for the wireless bridge. First of all, the main router should turn on the bridge mode, and fill in the WAN port IP address, MAC address, SSID number password or something of the wireless AP, this is the end, if the main router has MAC or IP filtering, you must add permissions.

Then there is the setup of the wireless AP, turn on the bridge mode, turn off DHCP, set the SSID and password. Enter the SSID, password, WAN port, IP and MAC address of the primary router.

Your diagram is Tietong, it is feasible to add a router behind the cat, pay attention to the LAN port address of the cat and the LAN port address of the router should be staggered, such as for the cat, then the router is used, and then the DHCP address pool is also used, in this way.

Wired Internet access is available.

1. How to set up two wireless routers for wireless bridging:

The first wireless router:

1) Log in to the router connected to the Broadband modem.

2) Set "SSID Number" and "Channel" in Wireless Settings - Basic Settings, and set the fixed channel number.

3) Set the wireless signal encryption information in the wireless settings - wireless security settings, and record the SSID, channel and encryption settings information after the wireless router is set.

2. The second wireless router:

1) Log in to the second wireless router that needs to be bridged.

2) In the network parameters - LAN port setting, modify the IP address to be different from the first router (to prevent IP address conflict) For example, save, the router will automatically restart.

4) Select the SSID number of the first router in the list of scanned signals and click Connect.

5) Set the channel to be the same as the first router channel. At the same time, set the encryption information to be the same as the first router, click Save.

6) Shut down the DHCP server. In the DHCP server, select Disable, Save, and Restart the router.

7) At this point, the first wireless router and the second wireless router have successfully established WDS.

3. The wireless router with wireless bridging can not only access the Internet wirelessly, but also have wired Internet access. No problem.

OK.

Wireless router to wireless router, the second router is set up, there are two ways (provided that the first router has been set up):

The first method: dynamic IP mode (the first route is the primary route, and the second route is the slave route).

1. Plug in the router and do not connect the LAN port of the main router first, and reset the slave router (restore the factory);

2. Connect the computer to either LAN from the router

to enter the settings page;

3. Follow dynamic i

p mode setting;

4. Then set the SSID, encryption method and password;

5. Save and restart;

6. After setting, put the main route to LAN

The network cable that comes out of the port is connected to the WAN port from the router.

The second method: wireless AP mode.

1. Connect the computer to the LAN port of the router first, and change the IP address of the slave router. For example, most router addresses are, we just need to change from router IP address to that;

2. Turn off the DHCP function from the router in the settings;

3. Finally, connect the network cable from the main router to the LAN port of the slave router (any one is fine), note that it cannot be the WAN port.

The wired bridging of routers is the best way to expand the wireless signal, and you are no longer afraid of weak wireless signals.

Wireless bridging method for secondary routers.

Is it impossible that a wireless bridge can transmit tens of kilometers? What equipment wireless power is so powerful, be careful not to come to the door to catch it, now through the civilian equipment of the wireless bridge is generally just a few hundred meters, the distance is too far will be greatly affected by the transmission power, intermediate blockers, etc., the distance of 5 kilometers is not realizable.

Do you have a fixed ** in your home? If there is a fixed **, you can use a fixed ** online Internet access OK. This depends on whether your home is connected to telecom or Netcom**.

After that, call the ** business hall that you pick up at home**, and let them open, and then you can buy a cat. Netcom's 4M bandwidth is about 500 a year.

Buy 5km of multi-mode fiber, 4 cores are enough, buy a 500-plus or so photoelectric converter, and use optical fiber transmission to transmit. Optical fiber is only 2-3 yuan per meter.

There is no way to connect the Internet online, so how can we talk about wireless bridging?

In which city can you set up an antenna at a distance of five kilometers?

It doesn't seem to work, it's too far away.

The bridge can transmit tens of kilometers, but it's more expensive than you can pull a cable.