Why can t ,,, the stove of beauty catch fire??

First, try to change the battery of pulse.

Second, the flameout protection is broken, find the manufacturer for maintenance.

It is possible that the air source is wrong. Buy a stove with the strength to make a stove, Jihua stove is good, it has been used for many years, and it is OK.

The sensor needle did not sense. So I can't catch fire.

1. It may be because the battery inside the gas stove is out of power. 2. If the gas stove uses a plug to connect to the power supply, it may be caused by poor contact with the power cord of the gas stove. 3. It may be that there is no natural gas. 4. It may be that the natural gas pipeline is blocked.

Suggested workaround:

1. If the gas stove does not catch fire because the battery inside the gas stove is out of power, you can buy the same model of battery replacement and then check if the fault can be solved.

2. If the gas stove uses a power connection plug to connect to the socket, you need to check whether the power plug is in poor contact, or whether the power plug is caused by rust, you can use a knife or alcohol cloth to clean the rusty place on the power plug to check whether it can catch fire.

3. Check whether the remaining amount of natural gas in the family is insufficient, the family natural gas will have a natural gas meter, and there will be the remaining natural gas balance on the table, you can also go to the natural gas company to inquire, if it is insufficient, you can fill the natural gas.

4. In general, if you can smell the smell of natural gas, but the natural gas stove does not catch fire, it may be that the natural gas pipeline is blocked.

If your Midea gas stove won't catch fire, it could be one of the following reasons:

1.Gas valve not open: Make sure the gas valve is open.

2.Bad match or lighter: Replace it with a new match or draft oak lighter.

3.Clogged fire: Please check the fire port for debris or oil stains, and try again after cleaning.

4.Spark plug failure: Please check if the spark plug is damaged or detached, and replace it if necessary.

5.Clogged gas pipes: Check if the gas pipes are blocked and clean or replace them if necessary.

If the above methods cannot solve the problem, it is recommended to contact professional maintenance personnel for maintenance. Do not disassemble or repair the gas stove without permission to avoid safety accidents.

1. It is very likely that there is an abnormality in the high-voltage line connecting to the gas stove, in which case I cannot ignite normally. 2. If the circuit of the gas stove has poor contact or short circuit problem, the Midea gas stove will not catch fire in the process of use. 3. The gas stove pipeline used for a long time may have been blocked, and the pipeline will be blocked, which will lead to poor circuits and easy to cause the problem of not catching fire.

Suggested workaround:

1. Check whether there is any abnormality in the loose rolling line, if there is an abnormal problem in the high voltage of the line or power supply, it is necessary to contact professional maintenance personnel, repair the circuit, and then reconnect it to resume normal use.

2. Generally due to the problems of this gas stove circuit, it is not recommended to dismantle and inspect it yourself, and you need to contact the professional maintenance personnel of the Midea manufacturer in time, and wait for the maintenance personnel to check clearly, and then carry out targeted maintenance or replace the components, so as to solve the problem of not ignition.

3. After the pipeline of the gas stove is blocked, it is easy to cause the circuit to be poor, so that in the process of use, not only will the stove not be on fire, but also may smell a smell of gas in the process of ignition.

First, the issue of lines.

High-voltage lines. The high-pressure gas stove is aging, and the stove has high-voltage lines and their joints. Once the high-voltage line is aged, it is easy to make the cavity empty stove not catch fire. At this time, only one set of high-voltage protection is required, which should be complied with in daily life.

Circuit. Poor circuit contact is an easily overlooked problem, but it is common in many old users. The main thing is to check whether the positive and negative poles of the battery box are rusty and whether the circuit is in poor contact. If the gas stove circuit is not in good contact, remove the rust and connect the circuit accurately.

Second, the ignition needle problem.

The position of the ignition needle is not suitable, if the ignition is ignited, there are certain requirements for the distance between the ignition needle of the gas stove and the fire cover. Once the distance deviates too much, the gas stove will fail to ignite. Generally speaking, the distance between the ignition needle and the fire cover is 4-6mm, and it should be aimed at the fire hole.

The ignition needle is dirty, and the pie kitchen is easy to get dirty, especially oil stains. If the gas stove is left for too long, the ignition needle can easily be soiled by the oil. At this time, Xiao Yuan He Hou had to clean up the oil stain from the ignition needle, and then try to light the fire.

Three. Miscellaneous questions.

Clogged pipes are a very common problem. Once the pipe is clogged, check the outlet valve. Generally speaking, if you can smell the smell of gas and the stove does not catch fire, it is likely that the gas is clogged.

If the gas stove pipe is blocked, it is necessary to unblock the pipe or replace it. Overvoltage protection, many gas stoves have overvoltage protection function. Once overvoltaged, they do not start.

If the gas stove is overpressure protected, you need to change the pressure reducing valve to try.

When the micro switch is damaged, it is a small place for the gas stove, but it is more difficult to repair than the usual fault. In general, it is not recommended for car owners to repair themselves. The micro switch of the gas stove was damaged. It's a delicate and professional job, so we have to call in experts to solve it.

The reasons why Midea gas stoves do not ignite are as follows:

First, the line problem:

1. High-voltage lines. The high-voltage line of the gas stove is aging, and the stove has a high-voltage line and its joint, once the high-voltage line is aging, it is easy to make the stove not catch fire. At this time, it is only necessary to add a set of high-voltage protection, which should be observed more in ordinary life.

2. Circuit. Poor circuit contact, which is a problem that is easy to ignore, but it is often seen in many old users, mainly to check whether the positive and negative poles of the battery box are rusty, and whether the circuit has poor contact. If the gas stove circuit is not in good contact, the rust needs to be removed and the wiring should be connected accurately.

Second, the ignition needle problem.

If you want to ignite the fire, the gas stove has certain requirements for the distance between the ignition needle and the fire cover, and once the distance deviates too much, the gas stove will not catch fire.

Generally speaking, the distance between the ignition needle and the fire cover is 4-6mm, and it is necessary to aim at the fire hole, the ignition needle is dirty, the kitchen is easy to be dirty, especially easy to be contaminated with oil, etc., the gas stove is placed for too long, the ignition needle is easy to be stained by oil, then you need to clean the ignition needle, and then try to ignite.

3. Other issues:

Pipe blockage, this is a very common problem, once the pipe is blocked, it is necessary to check the gas outlet valve, generally speaking, you can smell the smell of gas and the stove is not on fire, it is likely to be gas blockage. If the gas stove pipe is blocked, then the pipe should be unblocked or replaced. Overvoltage protection, many gas stove slag cloth has overvoltage protection function, once overpressure will not start.

If the gas stove is overpressure protected, then you need to change the pressure reducing valve to try. The micro switch is damaged, and then there is a very small place in the gas stove, but it is more difficult to repair than the usual fault, and in general, it is not recommended that the owner repair it himself. The micro switch of the gas stove is damaged, this is a delicate and professional job, and a specialist must be asked to solve it.

The gas stove is a commonly used kitchen appliance in our daily life, if the gas stove is not lit, then the purpose of the kitchen will not be able to play, and the food will not be able to cook, which will bring us a lot of inconvenience and trouble. Here are the possible reasons why Midea's gas stove doesn't ignite::

1.Gas pipeline failure: The gas pipeline of the Midea gas stove is faulty or blocked, or it may not be tightly connected or leaking, resulting in the gas not being able to be transmitted to the stove and thus unable to ignite.

2.Failure of the diversion line: The diversion line of the Midea gas stove may fail or be damaged, resulting in the current being unable to transmit to the ignition coil, so that there is no historical ignition**.

3.Ignition failure: There is a possibility that the igniter of the Midea gas stove may malfunction and cannot produce sparks, or the battery has run out of power and cannot make the igniter work.

4.Spark plug damage: The spark plug of Midea gas stove may be damaged and cannot produce ignition sparks, so that the gas cannot be ignited.

5.Pipeline cleaning is not timely: After Midea gas stove is used for a period of time, carbon deposits and impurities are easy to occur inside the pipeline, resulting in poor gas transmission and ignition**.

1.Check whether there is any leakage or damage in the gas pipeline, and repair or replace it in time if there is a problem.

2.Check whether the diversion line is tightly connected or damaged, and replace it in time if it needs to be replaced more cautiously.

3.Check the ignition for charge or damage, if the battery or the igniter itself needs to be replaced.

4.Replace the spark plug, if it can't be solved, you can find a professional to overhaul it.

5.Clean the inside of the pipeline regularly to remove impurities and carbon deposits for smooth gas transfer.

In short, there are many reasons why Midea gas stoves do not ignite, and we need to carefully check them, find the reasons and take corresponding solutions. At the same time, in daily use, we also need to pay attention to care and maintenance to avoid unnecessary failures.

1. The high-voltage line is aging, and the stove has a high-voltage line and its joint, once the high-voltage line is aging, it is easy to make the stove not catch fire. 2. Poor circuit contact. 3. The ignition needle is not properly positioned, and once it deviates too much from the distance, it will cause the gas stove to fail to ignite.

4. The pipeline of Pengshenghui is blocked, and if you can smell the gas smell and can't catch fire, it is likely to be gas blockage. 5. The micro switch is damaged.

Suggested Treatment:

1. The aging of the high-voltage line of the gas stove leads to the fact that the Midea gas stove does not ignite, and only needs to add a set of high-voltage protection, which should be observed more in ordinary life.

2. The main chain answer is to check whether the positive and negative poles of the battery box are rusty, and whether the line is in poor contact. If the gas stove circuit is not in good contact, the rust needs to be removed and the line is accurately connected, which can solve the problem that the Midea gas stove does not ignite.

3. If you want to ignite the ignition needle, generally speaking, the distance between the ignition needle and the fire cover is 4-6mm, and it should be aimed at the fire hole. The ignition needle is dirty, the kitchen is easy to be dirty, especially easy to be contaminated with oil, etc., the gas stove is placed for too long, the ignition needle is easy to be stained by the oil, then you need to clean the ignition needle, and then try to ignite.

4. If the gas stove pipeline is blocked, then it is necessary to be careful to pass the pipe or replace it.

5. The damage of the micro switch of the gas stove causes the Midea gas stove not to ignite, which is a fine and professional job, and must be solved by a specialist.