Regarding the sudden network disconnection, even the router settings interface is less than 100 logg

What the hell is your router or not.

According to your description, it is recommended to detect the problem of network disconnection from these places.

1. How many meters is the distance from the light cat LAN to the b-road chain pants hail, and is the distance too far?

2. Is the network cable a super Category 5 network, and is there a problem with the network crystal header?

3. There are too many routing network settings to automatically obtain, the optical modem dials up one layer, the A and B routes are divided into one layer, and then the A route is connected to another route.

Start from these aspects: 1. Call ** to the operator, change the optical modem to dial-up mode, use the route to dial, and then set the pure spike secondary route to AP mode, or directly change to AP

2. If the canopy sail network cable is super 5 class, the crystal head and the like are no problem, it is good to consider whether the distance is too far, if not, the network cable needs to be replaced with super 5 or 6 class.

2. Reseat the network cable for a slippery tour.

The network cable connected by the cat is connected to the WAN port of the wireless router, and the computer is connected to any LAN port of the wireless router.

3. Turn off the cat Wang and the wireless router and turn them on, and take a look later.

Fourth, if it still doesn't work, set up the wireless router again.

Does the cat connect to the wireless router, do you do this:

Plug in the wireless router, don't pick up the cat first, reset the wireless router (restore the factory), connect the computer to any LAN port of the wireless router, enter the router gateway address in the browser address bar (on the label behind the router), enter the settings page, and set it according to the PPPoe (ADSL virtual dialing) method.

Then set the SSID, encryption method, and password. Save, restart.

After setting, connect the network cable from the cat LAN port to the WAN port of the wireless router.

If you can connect and the Internet is normal, you generally have the following problems:

1. The network bandwidth is not enough, after the game, because the initial data exchange is relatively large, when the bandwidth is too small, it will cause disconnection, the solution is that the game character should not go offline in a place with a large amount of information in a place with many players, such as the main city or something, resulting in a card drop when going online again.

3. Game settings, for example, some large games such as WOW have IP6 options, if you choose but your network does not install IP6 protocol and does not support it, causing game login failures.

4. Trojan horses in the computer, which are forcibly disconnected, allow users to repeatedly enter passwords, increasing the probability of being tracked.

Prepare two network cables (the first one you have ready, which is the one that goes through the "modem").

The second is to buy a network cable sent by the router, if you don't send it, you have to make a network cable with crystal heads at both ends. ）

1.Change the local connection to automatically obtain the IP address.

2.The network cable that comes out of the "modem" is connected to the "wan" port on the router, and the router's ports (1,2,3,4) are either connected to the network cable port behind the computer host.

3.Open the browser and enter the password and username of the router are admin

4.Go to the router settings screen, select the PPPoE (ADSL virtual dialing) method, enter your home account and password, and confirm.

5.Then set the SSID, encryption method, and password.

6.Save, restart. In the end, the setup is considered successful.

Routers can establish flexible connections in a multi-network interconnection environment, and can connect various subnets with completely different data packets and media access methods. Recently, some users have reported that the router is disconnected when it is connected to the computer, resulting in the inability to access the Internet. Unplug the power supply for a while, and plug it back in is equivalent to being able to surf the Internet again after restarting.

Wireless routers.

Generally speaking, there are many reasons for this kind of router, and here are some common reasons, which you can find out which one is through the elimination method.

1. The processing capacity of the router is insufficient.

The router itself is a small computer, which also has its own CPU, memory, and operating system. Its task is to have a data frame. When you connect too many devices, it exceeds its processing capacity.

This will cause network congestion (such as too many devices connected to the router), which can be solved after restarting.

2. There is a problem with the quality of the router itself.

Many friends report that after 1-2 years of use, they found that their router response is slow, which may be the aging of electronic components, in some cases, due to poor heat dissipation, the main components of the CPU will run slowly, or Flash will run for a long time resulting in an increase in bad blocks.

3. Network congestion.

In terms of wireless, there are only 13 channels and there are interference channels, so if there are too many wireless signals around, they will interfere with each other and cause the network to be poor. (These issues may be resolved by restarting.) But it will often be reversed).

4.The reason for the business itself.

This is possible, but not very likely. You can dial up a computer directly by connecting the network cable without going through the router. Try it out to see if it will be disconnected (in fact, if you have experience, you can also see it in the settings interface of the router) If the line will be disconnected frequently, you can call the operator's customer service** and let them send a technician to solve it.

Finally, if it's a few days, the network will get stuck, and it will get better after restarting. It doesn't really matter. Remember to restart the router every few days.

Of course, friends who don't know how to solve it, can be solved by elimination, such as restoring the router to factory settings, resetting, reducing access to the device to try, in addition to not going through the router, directly plug in the computer dial-up Internet to try, if dial-up Internet access is no problem, the problem is basically locked in the router, cats, etc., network cables and other devices, if the device is very old, restore the factory and reset the settings, the problem is still the same, it may be that the router is about to break, it is recommended to change to a new router.

Summary. It may be that advanced security settings have been added. For example, if you set up the IP or MAC binding function in the router, once the function is enabled, you can only access the Internet normally if you set the binding mobile phone or computer in the router.

It may be that advanced security settings have been added. For example, Chi Wei set up the IP or MAC binding function in the router, once the function is turned on, only the mobile phone or computer can be bound in the router to access the Internet normally.

So when you encounter this kind of problem, you can log in to the absolute router to see if the MAC binding function is turned on, if so, you can add your mobile phone MAC or IP address binding, or you can turn off the IP or disadvantage MAC binding function.

I entered the login interface, and then looked at the current Internet ports, to see which ports have more traffic, and then closed the defense pin, and then the same card, after restarting the computer with Xiangyou, there is no network.

The router port cannot be closed.

What if it's closed.

After it is closed, you can't access the Internet.

I know I can't get on, and I want to ask what to do.

Why don't you try factory resetting your router?

With the router plugged in. Press and hold the reset button without letting go when the indicator light starts flashing again. It's a factory reset.

Then reset it on the router management interface.