How to cut the ten centimeter wide plaster line diagonally? How many centimeters are removed from it

Half of the horn is removed from the top, and 10 cm is cut from the bottom.

There are two ways to cut plaster lines:

1. The cut corner of the gypsum line should be determined according to the height of the paste and the size of the gypsum line.

The more practical method is to erect the gypsum line against the corner of the wall, draw two mark lines with a marker pen on both sides of the gypsum line, and then use a steel tape measure to measure the size of both sides, and when encountering the corner of the wall, you can generally paste 8 cm or centimeter in height, so that the beauty of symmetry can be shown when pasting the plaster line.

When decorating, the corners of the gypsum line are generally cut by hand or knife, and the installation speed should be slowed down when the gypsum line is cut at the corner of the wall.

2. The cutting of gypsum lines is mainly an angle problem, which is very similar to the corner lines of plastic gusset splicing, just make a right-angle card seat, and then put the line on the correct position and cut it directly at 45 degrees, if there is a 45-degree bevel cutting machine, it can be directly placed on the bevel cutting machine.

There is naturally a set of calculation methods for gypsum lines of different lengths, taking 7 cm gypsum line as an example, usually the length of the bevel angle to be cut off is 5 cm, because the width of the gypsum line is multiplied by the length of the bevel angle to be sawed off, and the angle and surface should be inclined when sawing.

Extended Information: Plaster Line Tapping Sounds:

You can use your fingers to gently tap the plaster line, if the sound is muffled and mostly inferior plaster line, if the sound of tapping is brittle, or even has a ceramic-like sound, then it means that the quality of the plaster line is good.

Inspect the drywall.

The elasticity of the plasterboard, when struck by hand, makes a very solid sound indicating that the gypsum board is strong and durable; If it makes a very empty sound, it means that there is a hollow drum in the board.

phenomenon, and the texture is not good. The weight of the plasterboard can also be measured by hand.

Gypsum line product repair:

First of all, use high-grade gypsum powder.

Add the special adhesive glue for the gypsum line, stir evenly, use the shovel paste, according to the meridians of the gypsum line to "carve", and when there is a little hardness, then brush the water with a brush, but not everyone can do the repair of the gypsum wall in the decoration. Secondly, if the color of the plaster line is not satisfied, it can be refreshed with paint.

The cutting angle is 45 degrees, and the cutting length is 10 centimeters.

When cutting the corners of the gypsum line, the position of the two gypsum lines is square, and according to the nature of the square, it can be known that the length of the cutting edge and the width of the gypsum line are equal, both are ten centimeters. When two plaster lines are spliced completely, the splicing line happens to be the diagonal of the square, and the angle of the splicing is 45 degrees.

Extended Information: Gypsum Line Construction Method:

1. Nail the wooden block with cement steel nails at the top corner or other parts to be installed, and the general specification of the wooden block is 15mm

60mm 50mm, the spacing is about 330mm, and the nailed wood block must coincide with the seam of the slider on the angular line.

2. Before installing each corner, the carved slider in the corner line must be cut out of a complete flower, and the sliding edge must be planed off so that the final nail can be glued to the cover.

3. Align the good angular line with the position of the wooden block on the top corner that has been nailed, push away the carved insert, drive in 2 3 round nails, push each nail forward a section, and the last interface is glued with the carved carved pre-cut glass glue to cover the nail hole to achieve a seamless effect.

Plaster sellers have plaster map brochures with plaster facade walls of various widths and sizes and roof covering widths. After knowing this width, take a small section of dozens of centimeters of gypsum line, draw the gypsum covering width line with a pen on the façade wall at the corner of the wall, that is, the line drawn along the edge of the gypsum line after pasting, put the gypsum line at the corner of the wall according to the line, and then draw the edge line on the roof, so that the top line of the roof is drawn on both sides of the corner, and the intersection of the two top lines is known. Push one end of the plaster line to the wall and mark the intersection of the roof of the plaster line, and the small section (a few centimeters) of plaster beyond this point is to be cut off.

In the same way, mark the other end of the plaster line. Then remove the gypsum line, erect the gypsum line on the ground, cut it in a straight line from the marked point to the diagonal, use a hacksaw, cut the gypsum line vertically, do not cut it on your stomach, (the gypsum line is cut lying down, so after cutting, the corners are right, and the middle is much empty). When cutting, the hacksaw can be sawed diagonally at 45 degrees, because the plaster has thickness, so that the front of the plaster is cut according to the mark, and the back of the plaster is cut less, so that it is convenient for the two plasters to be installed diagonally.

After cutting, take these two pieces of plaster and put them on the roof to see if they are neat, and after adjusting them slightly with a saw, you can use this plaster as a mold, and then cut other gypsum lines according to it.

The length of the 6 cm gypsum line bevel angle to be cut off is 5 cm, let's talk about the calculation method, the width of the gypsum line is multiplied by the length of the bevel sawed off, and the sawing should be oblique on both sides, the angle should be oblique, and the surface should also be oblique.

How do you cut the corners of the plaster line, nine centimeters?

Hello, dear, I am happy to answer for you: how to cut the corners of the gypsum line, nine centimeters? A:

There is a method for the chamfering of the gypsum line, so how to calculate the chamfering angle of the gypsum line, let pchouse tell you about it today. The calculation method of gypsum line chamfer is usually divided into two types: 1. Flat line chamfer:

Cut as wide the plaster line as. For example, a 10cm plaster line should be cut into 10cm and cut into a 45° diagonal; 2. Paste 45° chamfering angle:

How much to cut = plaster line width. For example, if you have a 10cm line, you usually cut 7cm.

Of course there may be 6cm according to a case. At the same time, when you cut the gypsum line, you should first put a vertical line at the yin and yang corners of each vertical line, and then use elastic lines to deal with it. And at 500mm on both sides of the vertical line of the yin and yang angles, we also have to put a parallel line to destroy the wax code.

Then measure with a ruler, when cutting the plaster line, the noise probably can't exceed 2mm, and then everything, so that the plaster line is cut.

If it is 7 cm, cut off the top 7 cm, cut it at 45 degrees, and cut it at 13 cm.

At each vertical yin and yang angle, a vertical line is placed with a line to drop for elastic line processing, and a parallel line parallel to the vertical line of the yin and yang angle is placed on both sides 500mm based on the vertical line of the yin and yang angle, and this line is defined as the "yin and yang angle standard line".

Before scraping the wall lining, the plaster is leveled within 500mm on both sides of the yin and yang angles, and the detection error is not greater than 2mm in the vertical direction of the 2-meter ruler. The yin and yang angles are 500mm away from both sides, and the plaster or wall lining is used to find Shun Ping.

The size of the gypsum line needs to be selected according to the size of the room, in order to adapt, the length and width of the gypsum line have different specifications, and the gypsum line with wide specifications is usually 150mm, 130mm, 110mm, 100mm, etc., and the length is etc. The specifications of narrow gypsum decorative lines are 40mm, 50mm, 60mm, etc., and the length is general.

Stick him on the corner of the wall and measure the edge from the corner to the plaster line, if it is 7 cm, you cut it off 7 cm and cut it at 45 degrees.

Summary. Dear, I'm glad to answer for you: The tips for cutting the corners of 10 cm plaster line are as follows:

1. All the yin and yang angles in the room are set with parallel and perpendicular lines.

2. Put the vertical line to detect whether the yin and yang angles are vertical and whether the error is too large.

3. Use gypsum line to make up the yin and yang angles, and control the error within 2mm.

4. According to the different angles of yin and yang, cut the angle of the gypsum line horizontally, or cut the angle at 45 degrees.

How do you cut the corners of a 10 cm plaster line?

Dear, I'm glad to answer for you: The tricks of 10 cm gypsum line angle cutting are as follows: 1. All the yin and yang angles in the room are set with parallel and perpendicular lines.

2. Put the vertical line to detect whether the yin and yang angles are vertical and whether the error is too large. 3. Use gypsum line to make up the yin and yang angles, and control the error within 2mm. 4. According to the different angles of yin and yang, cut the angle of the gypsum line horizontally, or cut the angle at 45 degrees.

The precautions for the construction of the gypsum line are as follows: 1. In the process of construction, the bottom of the wall needs to be treated to make it in a flat state, and if there is a depression or protrusion, it should be repaired appropriately. When the bottom is flat, the construction of the gypsum line can be carried out, so as to reduce the probability of the installation of the gypsum line and make the overall effect better.

2. For the installation process of gypsum line, it is also necessary to have a certain understanding. When building a plaster line, it is necessary to start from the front to reduce the number of joints and place them in an inconspicuous location. Moreover, in the process of paving, the gypsum line should be adjusted in time, otherwise it will be difficult to adjust once it is glued.

3. Special attention should be paid to the position of the corners and joints of the gypsum line, which determines whether the overall effect of the gypsum line is good or bad. Moreover, at the position of the gypsum line joint, the plaster needs to be scraped so that the docking can be replaced. Once the plaster line has been installed, it needs to be treated with clean water to ensure that it is neat and tidy.

The 10 cm gypsum line chamfer is divided into two situations:

1. Horizontal line chamfering: the broken rock surface should not be vertical, but oblique. As for the outer mouth oblique or the inner mouth oblique, you can search for it, and the way of oblique cutting will be different according to the different angles of yin and yang.

2. If the 45-degree cut angle is a flat line, the gypsum line is as wide as it is, for example, the 10-centimeter gypsum line is cut 10 centimeters and cut into a 45-degree diagonal.

If it is a 45-degree cut angle, there is a formula here, how much to cut = gypsum line width *, such as the 10 cm line of the reed brigade, generally cut 7 cm, of course, according to the situation 6 cm.

1. When decorating the gypsum line, be sure to use special glue and level the top corners. In this way, we can ensure that the construction effect of the decoration can be achieved at the best. And the next thing is to laminate, the fit must be tight, if it is not leveled, the plaster line is easy to crack, and then it will have to be reworked and redone.

2. If you want the plaster line to fit well, you must start the construction from the front. In this way, the neatness of the front can be guaranteed. In terms of details, when dealing with stubble, be sure to put it in an inconspicuous place and hide it.

In this way, the quality of the overall home decoration can be guaranteed, which is also the focus of the overall decoration.

1. Take a small section of gypsum line, set up a lead wall at the corner of the wall, and draw the gypsum covering width line with a pen.

2. Place the gypsum line in the corner of the wall according to the line, and then draw the edge line on the roof.

3. Huai which key pushes one end of the gypsum line to the wall, marks the intersection of the gypsum line roof, and cuts off the gypsum other than this point. In the same way, mark the other end of the plaster line.

4. Then remove the gypsum line, erect the gypsum line on the ground, cut it in a straight line from the marked point to the opposite corner, and use a hacksaw to stand the gypsum line and bend it slowly.

5. After cutting, take these two pieces of gypsum and put them on the roof to align them to see if they are aligned, and after adjusting them slightly with a saw, you can use this gypsum as a mold, and then cut other gypsum lines according to it.