What should I do if the apple is flooded and can t be turned on, how can there be repairs near Tongz

You can go to the Beijing Apple Repair Center, Room 13, 9th Floor, Block D, Wanfang Building, Wanda Plaza, Tongzhou District, or you can call the Apple customer service ** above to make an appointment, and the customer service can help you find the nearest regular Apple after-sales repair center. It is recommended to back up the important data on the mobile phone first, and then go to the relevant maintenance outlets to let the engineer detect the fault, and then determine the repair plan and maintenance**. The official website makes an appointment to select the time you want to go, it may be fully booked, and you can only make an appointment 3 days in advance.

If there is a vacancy, you will be asked to choose the time to go to the service.

To make an appointment for repair online, you need to make an appointment with the serial number of your iPhone:

Click "Settings", open "General", select "About this machine" under the interface to see the serial number, you can go to Apple's official website to make an appointment for maintenance.

The reservation process on Apple's official website is as follows:

Log in to the official website of Apple China, click on "Technical Support" at the top of the page, click on "View Warranty Status", enter the serial number, select "Arrange Maintenance", and after the appointment is successful, bring the machine and ID card to the Apple store for repair within the specified date. "

iPhone repair coverage.

Motherboard level: no wifi, no signal, white apple, restart, three no, iTunes interface, high current causes the phone to be hot, water short circuit causes the flash to be on all the time, the camera cannot be turned on, cannot be charged, audio damage leads to no phone delivery and no earpiece, touch IC damage causes the touch to be ineffective, short circuit causes the power consumption to be too fast, and other motherboard problems.

Accessory replacement: replace the touch screen, motherboard, baseband, middle frame, rear shell, power button, boot cable, audio cable, tail plug cable, home button cable, battery, front and rear camera, earpiece, speaker, vibrator.

Take the Apple computer macOS system as an example, if the Apple computer can't be turned on when the water is in, the solution to Lu Chunkuan is relatively simple, and the specific solutions are as follows:

1. If the computer cannot be turned on, you can first power off the power supply of the computer and remove the built-in battery to prevent short circuit or burning the hardware;

2. Then you can disassemble some parts such as the keyboard, hard disk, and memory of the Apple computer;

3. Then, if you find that there is obvious early bright water inside the Apple computer, you can use alcohol or absorbent paper to wipe the water inside;

4. After that, check whether the keyboard is flooded, and if it is water, it should be disassembled and cleaned up;

5. After wiping dry, you can use a hair dryer to dry the inside of the Apple computer to evaporate the water;

6. Finally, it is recommended to place it for 24 hours, and then install the dismantled parts, if it still can't be opened, you need to contact professional after-sales service personnel to solve the maintenance.

If the Apple computer gets into the water, don't rush to assemble it after cleaning it. The disassembled laptop can be placed in a relatively high temperature environment to evaporate the water vapor.

1. Easy to get liquid?

There are the most openings on the iPhone body, and the easiest thing to get into the liquid is the bottom, which has the "headphone hole", "tail jack", "phone MIC", "speaker hole", and then the card slot. The easiest thing to get into the front is the earpiece.

2. How to deal with it urgently after liquid ingress?

Water reacts electrochemically with many metals, especially when energized and the water contains complex ions, which can lead to more complex corrosion, much like this.

Nowadays, the mobile phone motherboard is highly integrated, the circuit is complex, and the mobile phone is likely to be open or short-circuited after it cannot be turned on by water, which may cause permanent damage in other places, and it can be rescued if handled properly.

1. Power off immediately.

If the battery can be removed, remove the battery immediately; If the battery is not removable and the mobile phone is still working, turn off immediately, and you can disassemble and disassemble the battery if you have the ability to do it; If the mobile phone can't be turned on when the water is in the water, look directly at the next step.

2. Correct placement.

After disconnecting the power supply, according to the different positions of the liquid intake, throw it out vigorously in the direction of the opening, and then follow the correct method, find a ventilated and dry place, and leave it for a period of time to dry, the purpose is to keep the liquid entering the fuselage from flowing to the motherboard as much as possible. This can only damage the screen, handset, or tail plug, minimizing the damage.

If the entire fuselage is soaked in water, it doesn't matter what self-help, the longer the motherboard corrosion, the more serious the corrosion of the motherboard. Find a reliable third-party repair shop as soon as possible to disassemble and clean up.

If it is part of the liquid ingress, according to the above practice to preserve the mobile phone, the functions are normal, at this time do not have a fluke mentality, should immediately find a reliable repair service provider to disassemble the machine for a comprehensive cleaning, with washing water and pure alcohol to treat the inside of the mobile phone is a complete strategy, the cost is only a few dozen yuan.

Twist the screws, disassemble the screen, disconnect the battery board, dry it with a hair dryer, and if it looks good, take it to after-sales maintenance.

iphone6 water does not turn on, pick up a leak, fortune small capacitor is here again!

Reasons why the Apple phone can't turn on:

1. There is no electricity. If you use up all the battery power, the charge needs to be charged to 5% before it can be turned on normally. So in this case, please let the phone charge for a while before trying to turn it on.

2. Software malfunction. If you are sure that the current battery of your phone is sufficient, but it cannot be turned on normally, there may be a problem with the software system of your phone. At this time, we can try to press the home button + power button on the home screen of the mobile phone at the same time until the screen is lit up and there is a display.

3. System crash. If none of the above solutions work, and you see an iTunes connection screen on your iPhone's screen, it means that your phone has entered recovery mode at this time. When this happens, the only way to do this is to restore the system for your phone.

Connect your phone with the computer with a data cable, press and hold the home button and the power button at the same time for 10 seconds, then release the power button and continue to press and hold the home button for 5 seconds, if you see the connection to iTunes, it is a failure, and you have to start again. If the screen doesn't light up after these 2 steps, you will enter DFU recovery mode, and then you can use iTunes to restore your iPhone, or use a third-party flashing software to reflash your iPhone.

The last thing you should do when your phone gets water is to turn it on. Because once you turn it on, the water flow can cause damage to the internal components of the phone. So when the phone gets water, the first thing to do is to turn it off, and then power it off.

Try not to turn it on until it is repaired. Then dry your phone in a cool place or in a desiccant. Then find the screen change brother to detect it, we need to take countermeasures, we don't operate blindly, otherwise it is easy to cause secondary damage to the mobile phone.

1. Shut down immediately

If our mobile phone accidentally gets into the water, then the first thing we have to do is to turn off the mobile phone immediately, because the mobile phone is still in the state of being turned on when the water is in, then it will cause a short circuit in the internal circuit of the mobile phone, resulting in damage to the mobile phone, so once the water is in, we should immediately turn off the mobile phone.

2. Wipe the water on the surface of the phone

After the mobile phone is turned off and the power is off, then we use a dry towel or paper towel to wipe the moisture that can be wiped on the surface of the mobile phone, so as to prevent the outside moisture from seeping into the mobile phone again.

Then we take out the SIM card inside the phoneIf necessary, you can take the phone apart by yourself and continue to wipe the moisture inside.

If we can't take it apart, then we throw it in one direction

Note that it is only in one direction (the charging port is facing down), and do not shake it around like a soda, which will cause a larger area of moisture to spread inside and cause more damage to the phone.

Then we found a hair dryer that we usually use to dry our hair, turned on the hot air, and paid attention to the temperature not to be too high.

Then we aim at the headphone jack of the mobile phone or other openings that can blow the air into, and aim at the mobile phone to blow the air, which can speed up the evaporation of water in the mobile phone.

After we use a hair dryer to dry the moisture in the mobile phone, we should not remember to turn it on, because there is still some residual moisture in the mobile phone at this time.

Then we can put the mobile phone into a dry packaging bag, and then put a large amount of desiccant in it, and use the desiccant to absorb the moisture in the mobile phone, of course, this method is suitable for the condition that there is desiccant next to us.

If there is no desiccant, then put the phone in a dry and ventilated place, and wait for about three days for the water to evaporate completely.

The iPhone X won't turn on when water gets in, the motherboard pins are black, and the tragedy caused by the small capacitor has appeared again!

1.Do not try to turn on the device immediately if there is water ingress. Because the iPhone has a built-in battery that cannot be removed, the motherboard will be short-circuited if it gets into the water, and if it is turned on, the motherboard will be burned, causing irreparable consequences.

2.You can first use toilet paper to dry the water outside the mobile phone, and then place the mobile phone screen horizontally to prevent water from flowing to the motherboard, and then use a blow dryer to dry the water, and turn on the temperature at medium or small temperatures.

3.Wipe the circuit board with anhydrous alcohol and try to turn it on. Because alcohol volatilizes quickly, the moisture on the circuit board can be volatilized clean.

4.Send it to a repair center for repair as soon as possible. If the motherboard is severely corroded over time, it will cause irreparable consequences.

First of all, check the damage of the mobile phone, if it just falls into the water and quickly scoops it up, the screen is on, but the touch screen is not working or can not be turned off, this is a normal situation, the damage is not serious. Leave it to dry for a week, or put it in a rice bowl. Don't use it for a week, after which the phone will generally not have major problems, and you don't need to take it for repair.

If you forget to take it out of your laundry, you find that your phone has been soaked in water for a while. In this case, the mobile phone is more seriously damaged, and the black screen should be the motherboard burned out. The first is, of course, to scoop it up and shut it down.

If you are at home, you must put it in a rice bowl. But for example, when I was in school, I basically didn't have any other way. Only quickly and recently find an Apple authorized repair shop to repair it.

Don't go to a small shop!! Few people know how to fix an iPhone! Especially if there is water ingress that causes problems with the motherboard or the screen of the DAO!

You go to the small store, he disassembles the machine for you, and it is easy to have problems there after Apple's after-sales! For example, you can't change the version of the new machine!!

After you go to Apple's after-sales service, he generally tells you that the water is in the water, 2500 for a new machine and 1500 for maintenance, but the maintenance is easy to have problems, and a lot of mess is to let you change the new machine! Don't be fooled! Insist on repairing!

As long as you haven't bought it for a long time (like the right to hard work, I only bought it for less than 1 month), he will give you a new machine!

First, the reason for the crash is that the machine cannot be turned on.

1.The mobile phone can't be turned on, it is divided into many kinds, if there is a crash failure.

2.Then there is no need to make a fuss, just contact Apple's after-sales staff to make an appointment for testing.

3.If you press and hold the power button and it doesn't turn on, remember not to try again, so as not to cause the phone system to malfunction.

How to deal with the iPhone won't turn on:

1. Check whether the iPhone has physical damage, such as: bending deformation or water ingress and other accidents;

2. Use the original data cable and charger to charge the iPhone, check whether the iPhone is responsive, and the battery may not turn on if the battery is insufficient;

3. Force restart your iPhone;

4. If there is still no response or cannot be turned on normally after the above operations, it is recommended to bring your mobile phone to a regular Apple customer service center for inspection and maintenance.

Turn it off immediately and put it in a ventilated place to dry or use a hair dryer to dry it before using it to avoid damage caused by the connection of electronic components.

1.Do not shake the body when powered on.

Once your iPhone gets water, it should be turned off immediately. Keeping the computer on in the case of water ingress will form eddy currents, cause short circuits, and the motherboard will burn out. So never turn it on.

2.The first thing to do after shutting down.

After shutting down, first wipe off the water on your phone's case with a towel. Then quickly unplug the SIM card and keep it somewhere else. Next, use a paper towel to suck up the water from the headphones, dock and SIM card slots.

3.Use a damp towel to wipe off hard-to-remove stains.

There are also many situations in which oranges are flooded and flooded. For example, in addition to fresh water, there are muddy water, sea water, fruit juice, etc. If fresh water enters the phone, you can wipe off the water with a towel after turning it off. If water enters the interface of the mobile phone, it can be removed with a paper towel or cotton swab.

store overhaul. The impurities in the muddy water and sea water are an important cause of the failure of the mobile phone. Beverages such as fruit juice and coffee contain sugar, and the same goes for lumps or salt.

After confirming the shutdown, a wrung out towel should be used to carefully wipe off any impurities left in the phone. If there is a foreign object attached to the earphone and dock port, it will corrode the phone and cause the phone to malfunction. So it should be carefully removed.

After removing the stain, be sure to use a dry towel to blot the fingers of your phone. Also, be sure not to wash stubborn stains on your iPhone with water to avoid excess water mixing with the inside of your already wet phone.

store overhaul.

4.Do not turn on the machine immediately after the exterior has dried.

Even if the iPhone body and interface are dry, don't turn it on. Because it also takes time to dry the water that invades the inside of the phone. Natural drying is the best way to get your phone back.

Never use a hair dryer to quickly dry the moisture in your phone. The battery of the iPhone is built-in, and the heat fraction of the hair dryer may age the battery and cause the phone to malfunction.

After drying the moisture, put the phone in a box with ** desiccant and let it dry for 4 to 5 days. If a special desiccant is not available, you can also use the food desiccant that comes with the food package. Although the effect is not as good as the former, it can also achieve the corresponding effect with more use.

In addition, if you do not have a desiccant, you can use a dehumidifier used in a closet, such as rice or Binchotan. The drying time varies depending on the degree of flooding and the change of seasons, but it takes roughly 2 to 5 days.