What s going on with the ignition electrode of the gas stove that keeps igniting

The general reasons are:

1.The switching spring is not elastic, or the elasticity difference cannot be restored.

2.High-voltage electronic igniter failure.

3.The solenoid valve is not opened, and there is no air outflow.

4.The thermocouple and the solenoid valve do not form an electrical circuit.

5.Flame-out protection device is faulty. and other reasons.

For details, please call us or report for repair.

If you let go of the lighter, the fire is burning, the ignition sound is still there, and it is not necessary to turn it off, which means that there is a problem with the lighter of your gas stove, and you can fix it yourself, if you don't understand it, since it is newly bought, it is best to repair it by the warranty, you look at it next time, and you will be on the side, and if the ignition sound is only a few seconds, it is normal.

Solution 1 of the uninterrupted power supply of the natural gas stove: After our natural gas stove is hit, Oak Youwu still has no power outage. This is because we have not disconnected the ignition switch of the natural gas stove, it may be that the ignition switch of our natural gas stove is malfunctioning.

We need to carefully check the ignition beam or close of the natural gas stove, if the ignition switch of the natural gas stove is because of stains and sticking, we only need to clean the switch of the natural gas stove. Use a clean cloth dipped in detergent and water to wipe the switch of the gas stove repeatedly to remove the stains on the switch of the gas stove. Solution 2 of the uninterrupted power supply of the natural gas stove

It is also possible that the parts of the natural gas stove have been damaged. We need to replace the damaged parts of the gas stove. Check the ignition switch and power switch of the natural gas stove to conceal and the induction porcelain needle inside the natural gas stove to see if there is a problem with these parts, and we need to buy good quality parts to replace them.

<> Reasons for the ignition of the gas stove and the non-stop ignition: 1. The induction needle is broken, which causes a false alarm and automatically cuts off the gas source and causes a flameout fault; 2. The loss of gas source may be due to the arrears of the gas meter; 3. The solenoid valve is extinguished due to poor performance or damage failure, resulting in gas interruption and output; 4. The battery is insufficient and cannot push and keep the solenoid valve working, resulting in flameout.

Excluding the above situations, the control assembly is damaged, and the pulse igniter is damaged, resulting in no power supply to the solenoid valve, which will eventually lead to flameout.

This answer is applicable to most brands of gas stove models such as Changhong, Fangtai, and Boss.

Summary. Dear, hello, after the natural gas stove is ignited, the electronic uninterrupted power is often caused by the adhesion of the ignition micro switch, that is, the lighter is damaged.

Dear, hello, after the natural gas stove is ignited, the electronic uninterrupted power is often caused by the adhesion of the ignition micro switch, that is, the lighter is damaged.

Pro, ignition micro switch Kai Jing Cong line electricity, oil sticking, switch aging, will cause electronic uninterruptible, treatment methods are as follows: 1: clean up the ignition switch oil stain 2:

The switch rotation of the gas stove is to switch on and off the gas, press down to ignite, and release the automatic reset to stop the ignition. If the ignition is still after release, the spring may fail or stuck, you will stare at the cherry up to see if you can cut off the ignition, if you can cut off the ignition, clean the shaft or replace the spring. 3:

Check the ignition circuit and replace it with a new one if necessary.

The gas source switch of the gas stove is not turned on or the air pressure is insufficient. Solution: After turning off the stove switch, check whether the front stopcock valve and the entrance switch of the gas stove are open, if not, try to light the light again after opening an account.

Gas stoves, ignition needles and hot spots are occasionally polluted or out of power. Solution: Check whether there are sparks when the stove is ignited, if there is no replacement battery, if there is a spark, it may be that the air inlet and nozzle of the regulator are blocked by rust, hindering the gas flow out of the bottle, and replace the qualified regulator.

Ignition failed.

If the valve in front of the stove is not opened, it will cause ignition failure, and check whether the valve in front of the stove is opened before ignition. Since moving the cooker will cause the connecting pipe of the cooker to twist and flatten, or because the gas contains more condensate to block the hose and cause the gas source to be blocked, and the ignition fails, the fault can be eliminated by checking whether the hose is compressed, bent and corrected or by replacing the hose with a new hose.

After the gas stove has just been replaced with a connecting hose, due to the air mixed in the pipe, it will cause temporary ignition failure, and the ignition can be successfully achieved by discharging the air in the pipe by igniting it multiple times. For users who use electric pulse ignition, the main reasons for ignition failure are:

1) The battery voltage is insufficient, the service life of the general battery is half a year to one year, and the battery should be replaced in time;

2) The high-voltage output wire is broken down or cracked, resulting in leakage, and the fault can be eliminated by replacing the new wire;

3) The electrode needle should be cleaned frequently due to too much fouling and weak discharge due to ignition failure, so it should be cleaned frequently to keep the electrode needle clean;

4) If the distance between the electrode needle and the ignition bracket is improper, the discharge will be weak or not, and the distance should be adjusted to 3-4mm;

5) The circuit board of the igniter is damaged and should be replaced in time;

6) Piezoelectric ceramic lighters generally have a long lifespan, and can be fired continuously for more than 30,000 times, but during the life cycle, there will also be a phenomenon that the fire cannot be fired;

7) The hammer spring can not produce sparks when it hits the piezoelectric ceramics weakly, and the spring should be replaced;

8) If the ignition mechanism is loose and unable to ignite, tighten the components of the mechanism;

9) Due to the dirt of the electrode, the distance between the electrode and the grounding discharge terminal is offset and the ignition cannot be ignited, the electrode can be adjusted to 3-4mm by wiping the electrode, and the fault can be fastened and eliminated;

10) For stoves with flame-out protection devices, the flame will be extinguished when the knob is released after successful ignition, because the device is in working condition at this time, and the knob can be released after a few seconds of gas burning.

The lighter head is sticky with oil, the high-pressure ignition is short-circuited, and it is used in the morning, the oil is dry, and it will be better at noon and night. It can be washed with dish soap and then dried with a clean cloth.

If it is only in the morning and there is no sound of gas, there is no feeling of insufficient electricity, and the gas supply pressure is too high, and the gas stove protection is started. Turn the gas valve off and just turn it on a little bit and wait a minute. Ignite again and it will be solved.

It should be that your side is humid, and there is night fog at night, and if there is more fog, it is water. It is difficult to have water on the stove.

Use pure alcohol (not disinfectant) to clean the ignition, and then adjust the distance of the ignition metal again, and then replace the ignition (14 yuan --**).

What's going on with not being able to catch fire in the morning.

This phenomenon is most likely due to a malfunction of the ignition device. The natural gas stove is powered by high-voltage electronic lighters, and the ignition does not stop, so the problem may lie in these two components. Let's talk about the reasons and maintenance methods in detail:

1. Check whether the spring in the switch button is loose. Generally, after the natural gas stove has been used for a long time, the spring in the switch will be loose or even deformed, which will cause the ignition needle to not return to its original position, prompting the ignition device to be igniting all the time.

Maintenance method: A new gas stove switch needs to be replaced to ensure the elasticity of the spring.

2. Check whether the lighter in the ignition device is burned out. This problem is also caused by the long-term use of gas stoves. If the ignition wire is broken, there will be a failure of the ignition or the ignition will not stop.

Maintenance method: Use a tool to detect the specific damaged parts in the lighter, and then replace it accordingly.

3. The solenoid valve is damaged. The solenoid valve transports the natural gas into the gas outlet and then ignites it through the ignition device. When the solenoid valve is damaged, it may result in the natural gas being delivered all the time or not at all.

Maintenance method: Check whether the connecting lines inside the solenoid valve are in good condition, and if there is a problem, reconnect the various lines.

It is recommended to replace the ignition and micro switch, and then check whether the connecting wire of the solenoid valve is connected, adjust the position of the thermocouple, so that the fire temperature can affect its normal use, if the flameout protection device is broken, then replace it.