What should I do if the Kunlun watch is not allowed to repair the watch hands

Five common reasons for watch time error and watch time inaccuracy:

1) Insufficient power reserve: You need to check whether the power is sufficient, if the amount of movement of the self-winding mechanical watch is very small, it may also cause insufficient power reserve, you can replenish the power by manual winding, and then observe whether it continues to have the phenomenon of fast and slow.

2) Insufficient power: If the quartz watch suddenly finds that it is slow, it is likely to be caused by insufficient battery energy, and you can send the watch to a special maintenance point to check the power.

3) Hit or hit: The watch is very tight, if it is hit or hit, it may cause loose damage to the internal parts, and it may also cause the problem of running time. This is to be dealt with in a timely manner.

4) Need to maintain: The lack of oil in the movement or the wear and aging of internal parts may cause time problems, which need to be maintained, and need to be sent to the designated maintenance point for maintenance services.

5) In addition to the above common situations, the watch is affected by some ambient temperatures: if the hairspring of the watch is magnetized, the watch will not be accurate.

Hello, it may be a lack of power, the fully automatic watch is completely dependent on the swing of the arm to complete the winding.

Therefore, if the watch is left for too long or the amount of arm activity does not meet the requirements of the watch winding every day, the watch will cause the mainspring to be winding and the potential energy is insufficient, which will cause the watch to be unstable or stop when it is not worn at night.

If this happens, we can manually do an arc movement before the watch is placed. Or use the manual winding function to wind the watch. This keeps the watch with enough kinetic energy storage to keep it running until the next day.

Recommendations for the use of mechanical watches:

1. Watches with manual winding movements should be wound at the same time every day as far as possible so that the watch has enough energy to operate in the next 24 hours.

2. The energy of the watch with automatic movement is ** in the movement of the wearer's arm, so there is no need to manually wind it under normal wearing, only when the wearer's exercise is not enough to replenish enough energy to the mainspring, it can be compensated by manual winding, and the crown rotation is controlled within 20 laps when winding.

3. For a self-winding watch that has not been worn for more than 40 hours, the crown should be turned 20 times to reactivate the movement when worn again.

4. In order to prevent moisture from penetrating into the case and maintain the waterproof performance of the watch, please make sure that the crown is locked at all times.

Since the hands are installed in layers, and the top tube is connected to the second hand, the second hand is usually lost. The crown should be pulled out in time to stop moving, so as to avoid the watch from moving around, so that the hands can scratch the dial or the hands will be damaged; For some hollowed-out watches, try to avoid the small needle falling behind the dial; After the crown of the watch is pulled out, it should be repaired in time to prevent the watch from entering the dust and damaging the movement. If the wheel tube is deformed, broken, or the parts are worn, the repair is slightly more difficult.

Mechanical watches are divided into manual mechanical watches and automatic mechanical watches, lack of power is an important reason for the watch to slow down or stop the watch, manual mechanical watches can be wound directly when they are slow, and the reason why automatic mechanical watches are slow is mostly because of insufficient wearing time or the arm does not maintain a normal amount of movement, and it can be directly manually wound to supplement the power.

Five reasons for watch time error and watch time inaccuracy:

1: Insufficient power reserve.

2: The battery is insufficient.

3: Having been hit or impacted.

4: Maintenance is required.

5: The watch is magnetized: If the hairspring of the watch is magnetized, the watch will not be accurate.

Mechanical failures such as magnetism, lack of maintenance, malfunction of the watch hairspring, escapement system, slippage of parts, etc., can cause the watch to be fast and slow. Mechanical watches are sometimes fast and sometimes slow, and it may be caused by severe impacts, water ingress, etc.

Our mechanical watches often have the situation that the time is not accurate, and most people wonder if the mechanical watch is broken. There are many reasons why a mechanical watch can be parked, but there are several main reasons.

1. Insufficient kinetic energy: The watch is not winded enough, and the kinetic energy is insufficient. In particular, automatic watches require more arm movement, and the winding efficiency is very low. If you usually exercise a little bit, you can wind it manually, which can ensure enough kinetic energy.

2. Gear failure: Gear train failure such as deviation wheel and center wheel failure will lead to the condition of stealing stop of the watch. These situations are often not easy to detect and require disassembly, careful inspection and testing to find out the problem and solve the problem.

3. Lack of maintenance: mechanical watches should be maintained every 2-3 years or so. If it is not maintained for a long time, a large amount of oil sludge will be generated inside. Friction between gears increases, causing slippage.

The main reasons why the watch does not go are: the movement gear is misaligned, the watch is magnetized, bumps, and the oil sludge is dried for a long time when it is left on hold. The most common reason for the failure of the watch not going is the lack of power of the watch and the movement of the watch does not work.

When the mechanical watch stops, the priority is to think about whether it is caused by lack of power. Hand-wound watches should be wound at the same time every day as much as possible so that the watch can operate with sufficient energy for the next 24 hours. Quartz watches, on the other hand, can be actively wound and should be worn on the hand for more than 8 hours a day to replenish the mainspring.

Lack of exercise after wearing it will also show that the watch does not move or stop.

If the watch is used for a long time, then its wear and tear will be more serious, and the external maintenance of the watch will be easily damaged. It is necessary to regularly replace the watch you are wearing, and it is necessary to maintain the watch regularly, for the service life of your watch, it is better to maintain it regularly.

If you find that your watch is going fast or slow and is not accurate, you can find a compass to diagnose whether the watch is magnetized. Place the compass flat on the table, hold the watch at close range and quickly shake it back and forth above the compass, and try the watch in a few directions a few more times, as long as the pointer moves, especially if the deflection is very strong, you can judge that the watch is magnetized. The watch is magnetized and it is best to take it to this repair center for demagnetization.

Usually take care of the watch, do not let the watch come into contact with items with strong magnetic fields, and it is best to keep a distance of more than one meter. Do not leave your watch next to TV, computer, radio, mobile phone, mahjong table, refrigerator, washing machine, speaker, car door, or leather bag magnetic buckle.

Another reason is that summer is coming, and the hot weather will go faster than the cold weather. Yes, there are two laws of physics here. One is the thermal expansion and contraction, the weather is hot, the hairspring will be a little elongated, this everyone wants to get, therefore, the lengthened hairspring, the swing will also increase, and the watch will slow down; On the contrary, when the weather is cold, the watch will go faster.

Hello, the reason for the inaccuracy of the watch watch may be:

The second hand and the minute hand are different from the minute hand and the hour hand, to which the latter belongs"Dead mesh"The position of the split wheel, straddle wheel and hour wheel is relatively fixed, and there will be no misalignment or movement under normal circumstances. The situation is not the same between the second wheel and the minute round, because the minute wheel will"Skidding", as soon as the needle is flicked, it will appear. In the case of a quartz watch, there are 3 cases:

1) If the battery is insufficient, the battery should be replaced.

2) The second hand is not installed during assembly"level"As a result, the second hand touches the bottom of the crystal, and the second stops.

3) The roar position in the middle of the second hand is too large, which causes the second hand to be tightened enough after being loaded into the movement, and the needle is loose, if the second hand is released against the bottom of the crystal, the second hand will stop.

The more common reason may be a lack of kinetic energy, but some friends may say that I buy a fully automatic mechanical watch, and I don't need to wind it myself. In fact, this is a big misunderstanding, automatic mechanical watches do not need to be wound manually, but to keep the mechanical watch on the hand to wear at least 8 hours of time, because the automatic mechanical watch is the use of the arbitrary swing of the rotor to wind up, and the rotor is swinging with the movement of the arm, so if the mechanical watch needs to be worn on the hand often.

But what if you wear it on your hand a lot and don't leave? Don't worry, it may be a lack of kinetic energy, and then we need to manually wind the clockwork.

After passing the above methods, what should I do if I also find that the machine is not gone? Here we can rule out the reason for the lack of kinetic energy of the mechanical watch, it should be that the mechanical watch is faulty, if you are not a watch professional, it is best not to disassemble it rashly, please send it to a professional watch repairer for repair. Before the watch bar talked about the maintenance method of mechanical watches, mechanical watches need more maintenance than quartz watches, here is an emphasis on the maintenance methods of mechanical watches:

1.If it is a manual mechanical watch, you should wind the mechanical watch regularly, and it is recommended to wind the mechanical watch around 8 o'clock in the evening.

2.If the arm movement of the automatic watch is insufficient, the watch needs to be wound manually, and the rotation of the crown needs to be controlled and made within 20 turns.

3.If an automatic watch has not been worn for more than 40 hours, it is necessary to turn the crown twenty times to activate the movement's drive system.

4.Regardless of the water resistance of the watch, it should be avoided as much as possible, and if it does, wipe it dry and make sure that the crown is locked at all times. It is best to replace the waterproof ring once a year.

What should I do if the mechanical watch is gone? We need to establish the common sense of protection of mechanical watches in ordinary times, and when we encounter the situation that we can't go, we don't need to worry, and we can eliminate them one by one according to the above methods, which are usually caused by insufficient kinetic energy.

The inaccuracy of the watch is a failure that we often encounter in our lives, because there are many factors that affect the watch time, and some people unconsciously lead to a large error in the watch. So, what should I do if the watch is not allowed to run?

1. Magnetization of the watch: The watch is in too much contact with items with magnetic fields, which leads to the phenomenon of magnetization of the watch, causing the watch to be inaccurate. After being magnetized, the watch may stop, slow, or fast.

After the watch is magnetized, its magnetism will not recede on its own, and it needs to be demagnetized to restore it to normal. Therefore, you can only go to a professional watch repair center for demagnetization so that it can return to normal.

2. Lack of maintenance: mechanical watches are maintained every 2-3 years, and quartz watches are maintained every 4-5 years. Watch maintenance requires the movement to be completely disassembled, cleaned, oiled, reassembled, adjusted, and functionally checked; Repair or replace any worn or malfunctioning movement components.

If the watch lacks maintenance, it will cause the parts to wear out, the sludge will dry up, affect the normal running time of the watch, and make the watch appear fast and slow. Regular maintenance of the whole machine can effectively prevent the occurrence of various failures of the watch.

3. Mechanical failure: Mechanical failures such as watch hairspring failures, escapement system failures, and parts and components may cause the watch to appear fast and slow, so when the watch is abnormal, you can first pull out the crown and take it to a professional maintenance organization for the maintenance technician to check the reason.

4. Of course, the mechanical watch is sometimes fast and sometimes slow, and it may be caused by severe impact, water and other reasons. The reasons are complex and require a service technician to carry out the repair according to the specific situation. Quartz watches are generally very accurate and less prone to time failures.

In the case of adequate maintenance, it is more likely to be fast and slow, which is more related to the failure of the circuit board, or the poor contact of a certain part.

If your watch suddenly does not go, then it is likely that the table has no output signal due to the following reasons, and all other aspects of the inspection are normal, check the circuit board with a multimeter without output signal, most of the reasons are due to the damage of the quartz oscillator or the failure of the integrated circuit, if the replacement of the quartz oscillator is invalid, then the entire circuit board needs to be replacedGear train faults, most of them are dust or foreign matter between the gear teeth, so that the gear train teeth are stuck with each other. There are also some tables where there is too much or very little oil, and too much oil causes adhesion between the wheels, wheels and splints.

Too little oil makes the rotation wheel train too resistant, which will make the electronic watch go badly. In case of these faults of the stepper motor and wheel train, they should be cleaned, removed from foreign matter, and refueled.

Coil breaking, due to oxidation or man-made reasons, so that the coil is damaged, can be checked by multimeter testing, and generally needs to be replaced. The meter battery is not charged or the capacity is insufficient, and a new battery needs to be replaced. However, the watch often finds that the battery is dead in a short period of time, which is generally caused by high power consumption or the low quality of the battery itself.

In this case, you should first find out the cause, troubleshoot, and then replace the battery with a new one. The contact is not good, most of them are dirt on the positive and negative electrode contact reeds, and the contact with the battery is poor. Poor contact can also occur when the signal output point on the board is in contact with the lead point of the coil tip.

These will cause the circuit not to be turned on, so that the watch does not go or does not go well, and it is found that the circuit is not open due to poor contact, first clean the contact surface sufficiently, and then reassemble it. The stepper motor can not rotate, and the rotor of the stepper motor is a permanent magnet, which often cannot rotate due to the adsorption of iron filings and the stator is stuck, causing the watch pointer to stop or stop when walking.