Which type of brake pad is good? What brand is good for brake pads?

At present, the brake pads made of ceramic materials are relatively good, with good brake performance, durability and stable use, which is more expensive.

RAL brake pads are a brand, and I think RAL brake pads are more reliable than brands in the industry.

Brake pads are divided into drum brake pads and disc brake pads according to the brake system, and the brake efficiency of the drum type is low, so the market is basically disc-shaped.

According to the material, it is divided into asbestos type, semi-metal type, and non-asbestos organic type.

The asbestos type has been eliminated, mainly because 1. asbestos is medically recognized as a carcinogen, 2. asbestos has poor thermal conductivity, and repeated braking will accumulate a large amount of heat, which will then lead to serious thermal attenuation, resulting in brake failure and danger.

The semi-metal hybrid brake pad has a high metal content inside, so the strength is high, but the friction of the brake pad is smaller than that of asbestos, and the vehicle needs a higher braking force to achieve the same braking effect, so the noise is high and the wear is high when braking.

Non-asbestos organic brake pads, referred to as NAO brake pads, are made of glass fiber, aromatic polyester fiber and other fibers such as carbon or pottery as reinforcement materials, to achieve the purpose of long service life and durability, but the cost is higher than the first two.

The car nanny came to the door to change the brake pads, and only closed the working hours.

Contact repair for so many years, to introduce to you the major brands of brake pads, a lot of car original standard brake pads, why each car manufacturer uses a different brand, mainly because the product bidding is not selected, does not mean that the brake pads on the bidding are not good, car manufacturers consider the cost issue, just like the original engine oil, the car factory over the years, used Shell engine oil, after a period of time found that it was replaced by Castrol!

Here are some of the big brands of brake pads.

1.Firodo.

The father of brake pads, 80% of the original brake pads of automobiles are equipped with Firodo brake pads, and the quality is needless to say! It works great!

2.Doctor. Dr. is the world's largest spare parts dealer, such as auto parts, electronic products, power tools, automotive FMCG, have his figure, brake pads are also civilized in the world, the main original supporting BMW, Audi, Volkswagen, Porsche, Fiat, Ford, etc. Reliable quality and trustworthy.

3.Milky Way. One of the world's top ten auto parts manufacturers, the world's top ten automotive brake pad manufacturers, its performance and quality needless to say.

4.Deco. The world's largest parts buyer, in addition to brake pads, also has spark plugs, batteries, antifreeze, etc.

5.Brembo.

High-end car procurement products, used in F1, Aston. Martin, Maserati, Porsche, etc., high-end products.

6, Sasaki, Dongdong promotion is very powerful, a Japanese name of the domestic brand, as well as Golden Kirin, Wearer, Ramboshi, Qufu Tianbo and other domestic brands, good brake pads, wear evenly, do not hurt the plate, no abnormal noise, car nanny business stay.

Answer: Brake pads are generally composed of steel plates, adhesive insulation layers and friction blocks, and the materials are mainly metal, NAO and ceramic, as well as asbestos, which have basically been eliminated due to the presence of harmful substances. At present, the more famous brake pad brands are Bosch, Firodo, Brembo, Tymington, Trina, etc., relatively speaking, Bosch is a relatively good brake pad brand, reliable quality, superior performance, cost-effective, has a high popularity.

Bosch, a Fortune 500 company, is a world-renowned brake manufacturer with factories all over the world, and its products are produced according to strict quality standards. Whether in the field of individual components or complete systems, Bosch guarantees a high market coverage. It has a complete range of brake pads, and its products are designated as original parts by the world's major automobile manufacturers.

Brake pads will inevitably wear and tear during the use of the car, the car has a total of 4 front and rear brake pads, if the front and rear brake pads need to be replaced, then how much are these 4 brake pads? Brake pads are different according to the brand, model and material, and they are also divided into front and rear.

Taking Bosch brake pads as an example, the front brake pads of the Japanese model Toyota Corolla NAO material are about 240 yuan, and the rear brake pads are about 200 yuan, that is, the 4 brake pads of the whole vehicle are generally about 440 yuan. You can also replace it yourself, but it is more troublesome, you need to disassemble the tire, it is recommended to go to the store to replace it, you need to pay a certain amount of working hours, about 50-100 yuan.

It depends on what kind of car you have, the European car is cheap, you can choose Firodo and Bosch and TRW's low metal formula, the friction coefficient is about right, the heat dissipation is also acceptable, the friction material bonding backplane technology, the disadvantages of high temperature thermal attenuation almost, the metal formula may occasionally have hard spots and a little bit of noise, the advantage is that it is very cheap. The pursuit of performance and comfort can be connected to the back plate with Rebesto's composite ceramic formula, friction material barb, high friction coefficient, no noise and low dust, almost no thermal attenuation, which is the best technology for civilian use, with high disadvantages. If you need the cheapest and most durable, then buy a domestic ceramic formula, but the friction coefficient is very low, the thermal attenuation is reduced, and the friction material is also a bonded backplate, which is particularly hard and wear-resistant, but the friction coefficient is too low, and there is always friction when braking, so it is basically dependent on the consumption of brake discs to achieve a long replacement cycle, and it is not recommended to use.

Kirin brake pad check, I personally tested, poor quality control. Cherish life and stay away from the golden unicorn brake pads.

What's right is best.

The higher the friction coefficient of the car, the better the braking effect, but the non-modified car is still not used.

The original one is good.

Brake pads are mainly divided into semi-metals, less metals, and ceramics The best ones in China are Bosch AC Deke Xinyi brake pads, and I personally think that Xinyi's is not bad Bosch AC Many products are made by Xinyi.

Xinyi brake pads The old sound is too hard I suggest you use the golden unicorn.

Go to a professional tuning shop and take a look, there must be something for you, and there is a lot of money for this thing. What's right for you is the best.

The goods in the 4S store are so fake, there are a lot of high imitations now, choose a younger brand, I think CQHY's brake pads are quite good, they are all in the high-end, the comfort is not bad, and the braking effect is excellent.

In fact, there is no need to go to 4S to see, many kinds of repairmen at 4S have greedy goods, private goods, and finally the high cost of the owner is very worthless. CQHY not only does a good job of brake pads, but also the machine air filter air conditioning filter oil is a high-end product, the price tends to be parity, which is very affordable for our car owners.

I know Shini brake pads are good.

Look at your car model, go to the 4S store and ask.

Now the performance indicators of brake pads mainly include the size of the brake pads, whether they are ventilated, etc., the top brake pads used in supercars are made of carbon porcelain materials, this kind of brake pads look like some cracks on the surface, but its performance is better than ordinary brake pads, characterized by good thermal decay resistance, wear resistance, but high cost.

The technology of brake pads is basically the same now, the brakes are now out of use, and the brake pads will also be suitable for engine braking, the latter technical requirements are a little higher, if you want to not come up with a high or low, it should be said that Volvo Cars should choose the best.

Braxe Brecx's brake pads are also very good, the characteristics of this product is safety, my brother drove a Nissan, last time he bought a brake pad on the ** Internet, the safety factor is very high, he changed it himself, the effect is very good, some brake pads on the market are too noisy, brake is not good, ceramic and other brake pads are very good.

The main brands of brake pads for civilian use are Bosch, Firodo, Champion and other joint venture brands, and the domestic ones are ASIMCO and Shandong Golden Scale. The brake pads should be soft as much as possible, although the brake ash is a little dirty wheels, but the brakes are sensitive, and the damage to the brake disc is also small.

Go to**see Huahua brake pads,**everything, try it once to know if it's good or not, Shanghai Polo Cup designated brake pads**business!

Huahua brand ceramic brake pads are good!

Specifically, it can be divided into the following points: High coefficient of friction stability: In the case of high temperature, pressure and speed, the friction coefficient of the brake pad needs to be high enough and have sufficient stability.

High adhesion resistance: It does not bond with the working surface of the friction pair, and does not produce peeling, abrasion, welding and other destructive damage to the friction surface. High heat resistance:

To be able to maintain the instantaneous friction temperature rise to 900 1000 and the long-term friction temperature rise to 300 400, its mechanical properties and friction properties remain basically unchanged. High thermophysical stability: The friction material should be able to withstand frequent thermal changes, i.e. resist thermal fatigue, while also having a fairly high thermal conductivity, specific calorific value and the smallest possible coefficient of linear expansion.

Sufficient mechanical strength: The material should not produce cracks, delamination, deep cracks, spalling and detachment from the steel back; A feasible rate of wear is guaranteed. High abrasion resistance:

The wear resistance depends mainly on the operating conditions of the brake pads. For powder metallurgy material brake blades, the allowable wear amount of the UIC is cm2 mJ to ensure that the EMU brake blades have a long enough life. High environmental friendliness:

Braking should be smooth and low noise; Asbestos and lead, which are not conducive to environmental protection, cannot be added to the material; It should be able to withstand moisture for a long time and at a temperature range of 60 to 50 with strong corrosion resistance.

Of course, disc brake pads are better. Others are slow.

All aspects are considered, and the brand of RAL brake pads can be obtained, and it is very good in all aspects.

Bosch is a world-renowned manufacturer of brakes.