If you don t have the right tools to buy engine oil, what is the best way to change the oil yourself

I bought the engine oil myself and took it to the auto repair shop to change it, after all, changing the engine oil requires professional technology, and it is even more difficult to change it without tools.

Semi-synthetic engine oil has been used before, and the quality is indeed not high, and the power is relatively mediocre. The best way to increase power is to change to a good quality fully synthetic engine oil. I bought the German GT engine oil change for my car, the effect was really immediate, the day before when I took the oil to the auto repair shop to change, the car felt almost boring, and I didn't dare to step on the accelerator.

The next day, when I drove again, first the car thief was quiet, and then the accelerator pedal was very light, and the power came up at once. This has been changed since the PAO engine oil, sharp acceleration and high rev power is enough and stable, and it is very comfortable to drive.

Changing the oil yourself requires professional tools and techniques, which is more complicated. If you want to improve the power better, you can change the car to the best fully synthetic engine oil. I bought German GT engine oil for my Buick car very early, and then asked the professional master to change it.

The power is so good that there is nothing to say, and everyone who has driven my car says it is good. The throttle is lightly stepped on, the power immediately rushes up, and it is very strong and stable, usually drive to 10,000 kilometers before the power feels a little down, before changing the ordinary fully synthetic engine oil, to 5,000 kilometers after the recession period and then driving is difficult, pao engine oil is not the same, the power decay is slow, and it is no problem to drive until 15,000 kilometers.

The tools you need to change the oil yourself are:

1. Lifting equipment (lift or replacement bracket);

2. an oil filter element wrench;

3. an oil-draining screw wrench;

4. Connect the waste engine oil basin.

To replace the oil yourself, you need to loosen the wrench of the oil pan oil drain screw, replace the wrench of the oil filter element, the rag, the jack, and the oil basin cover, and the specific operation steps for changing the oil are as follows

1. Use jacks to lift vehicles.

<>3. Loosen the oil pan drain screw.

4. Drain the oil.

5. Tighten the oil drain screws.

6. Unscrew the filter element.

7. Replace it with a new filter element.

8. The introduction of new engine oil is completed.

Most families can own a car, and engine oil maintenance is one of the most common maintenance items for cars, so can you change the car oil yourself? The oil can actually be changed by yourself, and here are the specific steps:

1. The engine of the car must be turned on first, and the water temperature must reach the specified range, and then extinguished. The car can be lifted with a jack or other tool.

2. Open the oil port at the bottom of the car and use a wrench to open the oil filter, which can be conducive to the secondary release of the filter. Warm reminder to wear gloves during the operation, the oil and filter element are very hot, be careful of scalding.

3. After the previous oil is empty, install the new oil filter. Pour in the oil that suits the specifications of the car, and you're good to go, remember not to add too much oil.

4. After changing the oil, start the engine, observe whether the oil volume is more or less, and see if there is any leakage in the lower part of the engine.

The text is not easy to describe, so it is recommended that you go to the fast repair shop outside to see how the master does it. Pay attention to what tools are needed and what the steps are, and you will be able to do it yourself next time.

You need to have a machine filter pliers, unscrew the machine filter, and then release the oil. The upper oil inlet should be opened to allow air to circulate. There is also an oil drain bolt at the bottom of the oil pan, and it is completely clean.

Then tighten the bolts. Take out the new filter, install it, tighten it, and add new oil from the oil inlet. And measure the oil volume with an oil ruler.

Not too much and not too little, just add it to the right one according to the ruler.

This can be easily done with a dedicated electric oil changer.

1. The oil change must confirm that the oil has reached the oil change period, (5000 km) 2. Choose the oil suitable for your own vehicle, it is recommended to use big brands, such as Shell and Henergy 3, change the engine oil as much as possible in the hot car state, and put the oil clean as much as possible;

4. The selection of engine oil must be more filtered.

5. The amount of oil to be added should be appropriate, and the oil dipstick should be confirmed;

6. Start the engine after adding the oil, check whether there is any leakage phenomenon in each component, 7. After starting the engine, run for 3 minutes to confirm the oil volume of the engine oil again 8.

The oil filter can be changed by yourself, but it is not recommended to do it yourself. Because the oil filter element is not screwed well, it is easy to slip, and the amount of oil is not well controlled, it is easy to add more or less, which will affect the normal operation of the engine. Engine oil is the "blood" of the engine, which plays an important role in the whole working process of the engine, not only to provide sufficient lubrication for the piston cylinder and the internal moving parts of the engine, but also to cool, seal, prevent rust, clean, buffer, etc.

1. First of all, open the oil filler cap and pull out the dipstick. Loosen the oil drain screw on the oil pan and catch the waste oil with a basin, and remove the oil filter by hand while draining the oil. After the standby oil is basically cleaned, unplug the high-voltage line on the distributor cover, start the motor for about 5 seconds, force the remaining oil to be discharged, and then install the high-voltage line and tighten the oil drain screw.

2. Pay attention when installing the oil filter: the new oil filter must be filled with oil, and the sealing rubber ring should also be coated with an appropriate amount of oil to prevent it from being crushed during installation. The oil filter is not tightened as tightly as possible, but it is advisable to use a wrench to twist 1 2 3 4 turns after it cannot be twisted by hand.

3. Fill the engine oil. Generally, an inline 4-cylinder engine with a displacement of liters requires about 4 liters of engine oil, please refer to the vehicle's manual for the specific amount. After the oil is added, start the engine, under normal circumstances, the oil pressure lamp should be extinguished, idle for about 10 minutes, check whether there is leakage in each part, wait a while after the ignition is turned off and then check the oil dipstick, the oil level should be located between the upper and lower limits, if it is insufficient, it should be added in an appropriate amount.

I can change the oil of the car, and the author once changed the oil of the car by myself. Below, the author will introduce the operation of changing the car oil.

We first use jacks to jack up the vehicle, and it is best to prepare wedge-shaped wood to support the vehicle in case the jack suddenly comes loose.

Then we find the drain bolt, unscrew the oil, and pay attention to the oil temperature to prevent burns. At the same time, you must let the oil drip for a while, so that it will be cleaner.

When we find that the oil is cleaned, we can screw back the oil drain bolts, taking care not to tighten it too much to prevent damage to the oil pan. Then we can unscrew the filter element and put the container under the oil filter. If the temperature of the filter is too high, wear gloves.

At the same time, be careful not to damage the interface screws on which the filter is installed and the components around the filter.

Then we can refer to the manual on board to select the appropriate oil filter, and remember to apply new oil to the interface gasket of the new filter.

To change the oil of the car by yourself, you must first know what brand of oil your car uses, and you must not change it wrongly, because the wrong change will damage the engine.

Prepare the oil, open the oil drain hole of the engine oil pan, put it clean, screw the cover, add new oil from above, look at the oil dipstick, and it's OK to get to the position.

Hello 1First, open the head cover, find the oil cap and unscrew it. (Under normal circumstances, it is best to warm up the car and open the oil cap to help the engine debris and oil discharge more cleanly).

2.The second step is to loosen the oil screws with a special wrench. (The wrench must find a special wrench suitable for the screw, so as to avoid problems such as oil leakage caused by the slippage of the screw, which causes the lock to not tighten the screw).

3.In the third step, gradually unscrew the screws with your left hand, and pick up the installation with your right hand.

Inconvenient, first of all, the car has to be lifted or there is a trench, in addition to the tools must be complete, but also to change the filter, it is very troublesome, it is very cheap to buy a service from a certain east!

The owner of the car must first have the tools to change the oil of the car, and then there must be supporting accessories. And you can find parts on the car (such as screws). In the end, you can disassemble and replace it yourself.

It is more troublesome to change it yourself, and it is dangerous.

Engine oil is a polluting substance, and individuals are not in a position to dispose of sewage, so it is recommended to go to a qualified repair shop to deal with it!