The router is frequently disconnected, so unplug the power supply and plug it back in.

1) **The line is often hit by wind and rain, which affects the communication quality, which is the main reason for frequent drops.

2) Poor communication quality. Generally, the communication status deteriorates due to the increase in noise, and errors occur frequently, especially when playing online games, due to external interference and the increase in the amount of communication, the connection will be dropped. As soon as the link is broken, ADSL re-debugs and reconfirms the link.

However, if the noise that caused the link to break is still there, the speed of the relink will be lower than before. Since the link speed determined in the debugging is fixed, the link speed does not increase even after the noise has subsided. The longer the cat works, the more likely it is that this will happen, so the connection is slower and slower.

At this point, if you restart the cat, the link will be re-established and the speed may be increased as a result. This common sense can be used as a countermeasure to deal with the slowdown of links.

3) The mains voltage in your area is unstable, causing a drop in power, you can buy a power regulator.

4) The quality of your ** line and network cable is poor, and it may be that the crystal head of your network cable is in poor contact (the crystal head is easy to have problems), then the line will naturally drop; If it is too far away from the junction box, you can replace the parallel wire with a twisted pair, which can effectively reduce the line loss.

5) There are too many people surfing the Internet at a certain time, or playing large online games leads to channel congestion.

6) The temperature of the computer working environment continues to be high, and the cat is overheated, which causes the semiconductor components on the cat to work unstable, causing the connection to drop. In addition, the cat's bad is also a big problem, you can change a cat to try, how to recover from the failure, that is, your cat is broken (such as your mains voltage rises instantaneously, suffered from lightning strikes or overheating, will damage the cat).

7) Viruses are playing tricks, such as ARP spoofing Trojans and killing them in safe mode. Then install a 360ARP firewall (note: don't use it if you're not a LAN user).

8) If you have a problem with your network card or the network card driver is unstable, try reinstalling the network card driver. Or reinstall the system with another version of the system disk, I once was a new system after the total drop, the hardware can not find the reason, and then change to another version of the system disk to reinstall the system The problem is solved.

Is it that there are too many computers under your router, there are too many computers, or someone is using BT** things, and the traffic exceeds the tolerance range of the router, which will cause the router to be disconnected.

In this case, there may be a problem with the route, and it often crashes, so it is recommended that you replace the route, Huawei's router runs stably, and there is another suggestion, which makes the operation of the router more stable, and disconnect the power supply when the router is not in use, so as to delay the aging of the electronic components of the router

It's a good idea to have one or two more routers at home, so you can try to see if it's a router problem or a network problem. If it's a network problem, call ** and let the operator repair it.

Is it possible that your router is broken, there is a problem with the network interface, or there is a problem with your network cable, this needs to be ruled out and then repaired.

The main problems of the router are that the router is old, the performance and stability of the router itself is not good, and the router is set up to connect on demand, etc., rather than automatic connection, which is more common in some old routers. Operator network problems are mainly problems such as operator servers, networks, and many simultaneous Internet users, which can be solved by consulting operators.

If it's not a bad network, then there's a problem with the router, maybe a better router will solve the problem! The so-called good point is one or two hundred.

If you are an optical fiber and directly connected to the router, you can report the fault, call the question mark to tell the customer, or report the fault to the 10000 (Telecom) app on the mobile phone. They will send a professional to carry out the repairs. If you're just having trouble with your router, you may need to get a new one.

In your case, if the router is always disconnected, it is recommended that you change to a better router. I want to try your router is a bit stuck, a little unresponsive, and sometimes the network will be disconnected, so it is recommended that you change to a new router.

The situation you mentioned is generally caused by a problem with the hardware of the router, and you can replace the router to eliminate it!

You try to do a factory reset, and each router has a button that can be reset again.

It may be that your router is old, and the contact is not good somewhere. The solution is to buy a new router.

It's true that the quality of your router is not very good, and I suggest that you change to a better router.

It's a problem with the router, let's change it to a different router.

1. The processing capacity of the router is insufficient. The router itself is a small computer that also has its own CPU, memory, and operating system. Its task is to have a data frame.

When you connect too many devices, it exceeds its processing capacity. This will cause network congestion (such as too many devices connected to the router), which can be solved after restarting.

2. There is a problem with the quality of the router itself. Many friends report that after 1-2 years of use, they found that their router response is slow, which may be due to the aging of electronic devices, and in some cases, due to poor heat dissipation, the main components of the CPU will run slowly, or the flash will run for a long time resulting in an increase in bad blocks.

3. Network congestion. A device in the LAN is using too much bandwidth for some reason (crazy** or poisoned). In terms of wireless, there are only 13 channels, and there are also interference reasons for the channel, so if there are too many wireless signals around, they will interfere with each other, resulting in poor networking.

These issues may be resolved by restarting. But it will often be reversed.

Not necessarily, if the broadband is in arrears, you will not be able to access the Internet, and you will have to pay a fee to access the Internet normally. If you can't connect often, your router may be unstable.

The router also has a cache, and when the cache is insufficient, there will be Internet lag, or even no access to the Internet. From the situation you described, it is the router's cache that is too small, and the cache is often insufficient. The solution is to restart the router regularly and it will be able to connect to the Internet.

You can also set up traffic control in the router to limit the speed of each Internet device, which can also make the network speed smoother.

In this case, if the network cable or line contact is fine, it should be the problem of the router itself, and it may be that the router is not easy to use. Just get a new router.

As follows: 1. If you usually use it normally, you can often restart it if you can't connect to the networkMost of the problems are with the router itself.

2. More is the 300m of TP, and the Mercury 2 3 antenna often has this problem.

3. It is best to change to a gigabit dual-band router, which can be used by Tengda, 360, and Huawei.

This situation should be a problem of the router itself, it may be that the router will not automatically refresh and reconnect to the network after the network is disconnected, just reset the router or change it to a new router.

There may be a problem with the router.

Problems with laptop network cards. Laptops are equipped with wifi and can be connected wirelessly using a wireless router.

First of all, is it a laptop or a desktop? If you don't disable the wireless for the laptop, the two conflict, and the desktop should be a network problem.

Is Benben hot after more than 10 minutes? Sometimes the laptop overheating can cause hardware errors. There is also a place where you can take this book to a place with wifi to try the Internet,If there is a problem,Then it's a problem with the routing,Try to restart the route,Put it in a spacious place as much as possible,You must know that the route is too hot and there will be an error。

When the traffic passing through the router exceeds the load capacity of the router itself, the router is prone to suspended animation, and the network will be disconnected, and the router needs to be powered off and restarted before it can be recovered. In addition to restarting the route, you also need to check and kill the ARP virus on the intranet and bind the MAC address.

ARP attack is to achieve ARP spoofing by forging IP addresses and MAC addresses, which can generate a large amount of ARP traffic in the network to block the network, and the attacker can change the IP-MAC entry in the ARP cache of the target host as long as the attacker continuously sends out forged ARP response packets, causing network interruption or man-in-the-middle attacks.

If a computer in the LAN is infected with an ARP Trojan, the system infected with the ARP Trojan will try to intercept the communication information of other computers in the network through "ARP spoofing", and thus cause the communication failure of other computers in the network.

Ken can be a problem with the router:

It is recommended to reset the router and set the dial-up again;

Reset router method;

Method 1: There is a button [RESET] button behind the router, press and hold it for 5 seconds, and then reset it;

Method 2: Go to the router --- System Tools --- reset the router;

Set up router dialing:

Automatic acquisition of computer IP and DNS settings;

1. Enter the router. In the [Setup Wizard], select [PPOE Dialing] (some are ADSL Dialing), enter your Internet username and password as prompted, and save;

2. In [Network Parameters] --WAN Settings], select [Normal Mode], and select [PPOE Dialing] in the three options of [Connection]. The next is to select [Auto Connect], Save, and Exit;

3. If you want to use wireless wifi, your router must have a wireless routing function, in the settings, turn on the wireless routing function, here, the wireless signal signal is changed to one of them. The strongest anti-interference.

You can also set a password for your Wi-Fi connection.

You try it!

You can try cloning a mac address to give it a try.

Use your computer that often surfs the Internet, log in to the router, go to the network settings, clone the MAC address, make the MAC address of the router the same as your computer, save and restart, and see how it goes.

If it's not too stable, you can set the DNS address to be fixed. These are two free 114 DNS quite easy to use, if you clone the MAC address is not good, you enter the network parameters, select advanced settings, there is a manual setting DNS, you use these two, see how it goes.

You can connect a computer directly to the Broadband Cat without using the router to test if the connection continues to drop. If it is still the same situation, it may be a problem with the operator, call the operator's customer service and let someone be sent to deal with it; If you directly connect to the broadband modem, and the connection router is faulty, it may be a problem with the router, you can restore the router to factory settings and set the relevant network parameters again for testing.

Long press the factory recovery button on the router, re-set it, if it still doesn't work, there is a problem with the line, try to change the cable, if it doesn't work, you can only change the router!

It's fake death, don't make a fuss.