The starter is not just the motor, how many watts can the general starter of the motorcycle, how man

The starter is originally a motor, and the motorcycle starter is generally more than 2000 rpm. The starting current reaches 80A when it is very high

The starter is the motor, but most of them are DC motors, the DC motor starts with a large torque, and the starter on the motorcycle is very small, and I don't know the specific value, you can check it again.

The starting motor generally does not look at the power, but at the speed, voltage, current, and torque. It is divided into no-load and load-loaded cases. No load 1kr min is normal.

The power of the motorcycle starting motor is in the range of 200-500W, and the working current is small at 40-50A under rated load, and the large is more than 100A, and the braking current of the motor can be as high as 100-250A.

The normal operating temperature of the engine is designed to be between 80 and 110. Too high a compression ratio may cause gasoline to spontaneously ignite and pre-ignite, which can cause detonation, weaken the engine and damage mechanical components. Therefore, it is crucial to increase the compression ratio while maintaining the normal operating temperature of the engine.

Electric start motor of the scooter, 12 volts 5 amps 60 watts. This is a permanent magnet DC motor, the stator is 4 permanent magnets, and the rotor is wirewound with brushes. Rotational speed 2000 rpm This kind of motor works intermittently and cannot be used continuously.

The specific speed of the starting motor of the motorcycle will generally be lower than 1000 rpm, because after starting, the idle speed of the engine is at least more than 1000 rpm, and the normal should reach 1500 rpm, and even when the low speed of 1000 rpm, the speed is already higher than the starting motor.

At this time, if you press the start button, you will find that under the action of the starting overtaking clutch, the starting motor will not be injured, and the speed is lower than the starting speed, so it will definitely not reach the high speed of 2000 or 3000.

Try the wiper motor! The torque is sufficient, the rotation speed is low, and the speed is adjustable, and most importantly, it can be used for a long time.

LS. LZ is asking about air motors, not engines. It's the motor connected to the electric start switch on the right hand side of your motorcycle.

You must know that the motorcycle starts the motor to reach the crankshaft, but also to reduce the speed of the principle of increasing the force, the speed is about 20,000 revolutions per minute, depending on the battery voltage, the torque is not clear, the power is about 5a, the current is 7, 8a

Summary. Pro, the specific speed of the starting motor of the motorcycle is not clear, but it will generally be lower than 1000 rpm, because after starting, the idle speed of the engine is at least more than 1000 rpm, and the normal speed should reach 1500 rpm, and even if it is a low speed of 1000 rpm, its speed is already higher than the starting motor, at this time, if you press the start button, you will find that under the action of the starting clutch, it will not hurt the starting motor, and its speed is lower than the starting speed, So it definitely won't reach the high revs of 2000 or 3000.

Hello, dear, I'm glad to have your question, how many revolutions of the motorcycle starting motor in a minute, help with the age of limbs you inquired, the motorcycle start generally has to reach two or three thousand revolutions to drive normally, and the top speed is more than six thousand revolutions. The idle speed is generally 800 to 1200. Hope mine can help you.

I wish you good health and a happy mood

Pro, the specific rotation of the starting motor of the motorcycle is suspected of judging the speed is not clear, but it will generally be lower than 1000 rpm, because after starting, the idle speed of the engine is at least more than 1000 rpm, and the normal speed should reach 1500 rpm, and even if it is a low speed of 1000 rpm, its speed is already higher than the starting motor, at this time, if you press the start button, you will find that under the action of the starting clutch, it will not hurt the starting motor, and its speed is lower than the starting speed, So it's definitely not up to 2000 or 3000 high revs.

Hello dear dear, I am happy to serve you: the motorcycle starting motor is generally a minute will be lower than 1000 rpm, because after starting, the idle speed of the engine is at least 1000 rpm, and the normal to reach 1500 rpm, and even if it is 1000 rpm low speed, its speed is already higher than the starting motor, then if you press the start button, you will find that under the action of the starting clutch, it will not hurt the starting motor, and its speed is lower than the starting speed, So it definitely won't reach the high revs of 2000 or 3000. Thank you for your trust, the above is my reply, I hope it can help you, I wish you a happy life.

The motorcycle starter motor is a DC motor with a working voltage of 12V.

The motorcycle starter motor is a small high-power short-time working DC motor, a single working time can not be greater than 15 seconds, the working voltage is generally 12V, the no-load current is 10 25A, the working current is 40 100A, depending on the model, and other small models The working current is about 40A, and the working current of Halma 150 or double-cylinder CBT can reach 150 200A.

When the DC power supply is supplied to the armature winding through the brush, the conductor under the n pole on the surface of the armature can flow through the current in the same direction, and according to the left-hand rule, the conductor will be subjected to the torque action in the counterclockwise direction; The conductor under the S pole on the surface of the armature also flows through the current in the same direction, and the conductor will also be subjected to a moment in the counterclockwise direction according to the left-handed rule.

In this way, the entire armature winding, i.e. the rotor, will rotate counterclockwise, and the input DC energy will be converted into the mechanical energy output on the rotor shaft.

The 100 amp instantaneous starting current is 8 to 10 times that of the load.

The current of the motorcycle 125 ml when starting with a motor is 25A.

Motorcycles, driven by gasoline engines, are two-wheeled or three-wheeled vehicles that are steered by handlebars, are lightweight, flexible, and fast, and are widely used for patrolling, passenger and freight transportation, etc., and are also used as sports equipment. In terms of general direction, motorcycles are divided into street bikes, road racing motorcycles, off-road motorcycles, cruisers, station wagons, etc.

Motorcycles are a flexible and fast means of transportation that are also used in military and sports competitions. Equipped with an internal combustion engine. There are two-wheeled and three-wheeled motorcycles.

The motorcycle starter motor is a DC motor with a working voltage of 12V.

Motorcycle electric start system and working principle:

The motorcycle electric start system is mainly composed of starting relay, starting motor, battery, starting button and ignition system (ignition coil, trigger block, high-voltage wire joint, spark plug, etc.). Starting motors, also known as starter motors. It is a special DC motor with small size and large power.

The starter motor is mainly composed of a stator and a rotor, a base, etc.

It works on the principle that when the motor is fed with a mains current, the stator armature windings of the motor generate a rotating magnetic field. If there is a relative motion between the rotating magnetic field and the stationary rotor, the magnetic field lines of the rotating magnetic field will cut the rotor conductor, and the rotor conductor will generate an induced current. This current interacts with the rotating magnetic field to generate electromagnetic force, and forms an electromagnetic torque on the rotating shaft, which rotates the rotor, and the rotor drives the engine crankshaft to rotate through the driving device to start the car.

It must be a DC motor, the same voltage as the motorcycle battery, which may reach about 100A when starting at 12V.

The starting motors of motorcycles are all 12V true flow motors, and the starting current is generally about 10 A. If it's 100 amps, it's not bigger than the starting current of a big car!!

DC motor, generally 12V

It may reach around 100A at startup.