The computer always enters the Aptio setup Utility, and cannot enter the system

Select to the boot menu and take another picture** to see.

1. It is recommended that you restore the BIOS factory default settings to try it, recovery method: in the BIOS interface, press F9 key to restore, press Enter, F10 save, press Enter, the computer will automatically restart, and the recovery of BIOS default value is completed.

2. If the notebook has been equipped with expanded memory, it is recommended that you take out the expanded memory and then boot it up for testing to avoid incompatible memory causing abnormal boot.

3. Sorry, not sure which version of the system you are using? If the above methods still do not work, we recommend that you back up and save important data to a USB flash drive or portable hard disk, and then restore or reinstall the system.

The reasons and solutions for aptio setup utility after the computer is turned on are as follows:

The reason may be to check whether the computer has a floppy drive or whether the floppy drive is broken, if the computer does not have a floppy drive but the BIOS is set up with a floppy drive, you have to press F1 to continue when you boot the computer. The solution is to restart the computer, go to the BIOS settings, and set the floppy drive to none.

The reason may be that the computer originally had two hard disks, which were set up as dual hard disks in the BIOS, and later removed one of the hard disks or one of the hard disks was damaged and the BIOS settings were not changed back. The solution is to restart the computer, go to the BIOS settings and change the dual hard disk to a single hard disk.

If the motherboard battery is out of power, it will also cause data loss, so this fault will occur, just replace the battery.

The failure to respond at boot is mainly due to problems with the power supply and motherboard. First, check whether the plug of the computer is properly connected and whether the power cord is normal.

Then check whether the wiring in the chassis is connected properly, if it is normal. Then check whether the power supply is damaged, you can take another power supply and try to replace it.

If none of the above methods solve the problem of unresponsive computer boot, then it is likely that the motherboard is damaged. Check whether the wiring on the motherboard is normal. If none of the above operations can solve the problem, it is recommended to send the computer for repair.

The Aptio Setup Utility is a program for managing your computer's BIOS settings. If the computer automatically enters the aptio setup utility after booting up, it may be due to one of the following reasons:

internal computer malfunction or hardware problems;

There is a problem with the BIOS settings or needs to be updated;

There is a problem with the operating system, such as a missing or corrupted startup file.

Here are some steps to handle the Aptio Setup Utility:

Check the hardware connection: Open the computer case and check whether the internal hardware is firmly connected, including hard disk, memory, graphics card, power supply, etc. If there is a loose place, plug it back in and check it.

Restore the default settings: In the Aptio Setup Utility interface, find the "Exit" option, select "Load Setup Defaults", save and exit.

Update BIOS: In the APTIO Setup Utility interface, find the "Advanced" option, find the "ASUS EZ Flash Utility", select the option and follow the instructions to update the BIOS.

Reinstall the operating system: If none of the above methods resolve the issue, you may need to try reinstalling the operating system. In this case, it is recommended to back up your important data and then reinstall the operating system using Install**.

If you are unfamiliar with these steps, it is recommended to contact a computer repair professional for assistance.

What settings have been made in the BIOS before? It is recommended to restore the previous settings.

You can also try the following troubleshooting steps:

1) If you can't find the device that can be turned on, please confirm whether you recognize the hard disk, reset the hard disk to turn it on, and then confirm whether the problem is solved.

2) Under the BIOS, see if the other pure liquid settings are abnormal, and whether the time is restored to 0:00 on January 1, if so, you can try to update the BIOS, or replace the CMOS battery of the motherboard (CR2032).

3) If it appears every time you boot up, please test the situation of turning on the hard disk of the single connected system under the most miniaturization test.

This situation should be that the motherboard battery is dead, the BIOS system time is wrong, you have to go in and set the system time to save and restart! Replace the motherboard battery as soon as possible!