-
Anonymous users2024-02-06The operation method of changing the shaft of the mechanical keyboard - original.
The operation method of changing the shaft of the mechanical keyboard - original.
After that, the board is slightly erected, after the soldering iron is heated, add tin, burn the two feet of the lamp, press the inside of the PCB with the soldering iron with the right hand, and remove the LED light with the left hand.
The operation method of changing the shaft of the mechanical keyboard - original.
The operation method of changing the shaft of the mechanical keyboard - original.
The operation method of changing the shaft of the mechanical keyboard - original.
Press down the spring of the solder, use a soldering iron to melt the foot of the shaft, and then use the sniffer to suck out the tin in the foot, making sure that the pin foot is not connected to the board; The other is the same method;
The operation method of changing the shaft of the mechanical keyboard - original.
The operation method of changing the shaft of the mechanical keyboard - original.
The operation method of changing the shaft of the mechanical keyboard - original.
Then use a hard object (wooden rod, tweezers, etc.) to press down the shaft rod and remove the shaft.
The operation method of changing the shaft of the mechanical keyboard - original.
The operation method of changing the shaft of the mechanical keyboard - original.
After that, take a new shaft, align the foot, insert it, and fix it with two feet.
The operation method of changing the shaft of the mechanical keyboard - original.
The operation method of changing the shaft of the mechanical keyboard - original.
Install LED lights, at this time, you should look at the front and back of LDE, and see how other lights are placed. Use a soldering iron with your right hand to melt the two feet behind the lamp, and insert the lde with your left hand and shake it gently. (You can also suck out the two feet of the LED light on the PCB with a solder suction device first, and then install the LED light).
In addition, the two feet of the LDE should not have the phenomenon of tin connection (easy to burn the plate). In this way, the problem of the keyboard is easily solved.
The operation method of changing the shaft of the mechanical keyboard - original.
Finally, reassemble the keyboards and put them on.
-
Anonymous users2024-02-05The A-axis of the keyboard doesn't feel good, so I need to change it.
-
Anonymous users2024-02-04The following gives the method of disassembling the axis of the mechanical keyboard:
Materials required: keycap puller, shaft puller, mechanical keyboard.
1. Prepare the two gadgets in the picture below, which are the keycap puller and the shaft puller.
Second, the keyboard needs to remove the keycaps first, and then use the keycap puller to clamp the two sides of the keycaps and pull them up to remove them.
3. Then use the shaft puller, insert the two tips of the shaft puller into the hole of the key shaft, and then pull it up to pull it out.
-
Anonymous users2024-02-03When the vast majority of mechanical keyboards change switches, users need to disassemble the keyboard and remove the keycaps, if only one shaft body is replaced, there is no need to remove all the keycaps, only one keycap can be pulled.
1. First plug the soldering iron into the power supply, then wait for 1 minute to reach the appropriate temperature, take out the disassembled mechanical keyboard circuit board and reverse the back, and see that a key switch is fixed at the position shown in the figure below.
2. Then use the heated soldering iron to dissolve the back of the tin.
3. After dissolving the tin, use a tin suction device to absorb the tin.
4. Then use the empty mandrel to pass through the key shaft hole below and rotate it slowly.
5. To the corresponding keyboard axis of the front, with tweezers.
Gently pry open the shaft on the mechanical keyboard.
The difference between various mechanical keyboard switches What kind of axis is good.
Choose the orientation,I have used a lot of mechanical keyboards one after another,Here is a recommendation for you,Black axis,Personally, I think it's a game orientation,A piece of falling,Plus a heavier sense of pressure,If used for long-term typing,The hand is more sour。 >>>More
How to disassemble the shaft of a mechanical keyboard.
Since the switch of the keyboard is the most important part of the mechanical keyboard, how to skillfully and accurately disassemble the mechanical keyboard switch has become a lesson that everyone must learn. First of all, for those high-end, mechanical keyboards with steel plates, we need to use a solder rod and an electric soldering iron, use solder after heating the electric soldering iron, after the solder is sucked up, use small tweezers or other tools to clamp the shaft tightly, and at the same time clamp the bayonet of the steel plate, so that the shaft can be smoothly disassembled, after completing such steps one by one, and finally continue to use the electric soldering iron and solder to re-solder the contact point just now. If your mechanical keyboard is not a high-end mechanical keyboard and does not have a steel plate design, then the step of removing the small tweezers to clamp the bayonet in the previous step is done. >>>More
Basically, I personally feel that any axis can be played. The switches of the mechanical keyboard provide a different feel, and there is no question of whether it is suitable for gaming. But most people still think that Black Axis is suitable for gaming. >>>More
Strong sense of passage but very noisy (cherry black),Professional players generally like the red shaft or the tea shaft,Feel light and won't feel very tired for a long time to play,The gap between the red axis and the tea axis is that the brown axis has a little bit of a sense of paragraph,In addition, the Corsair currently has an exclusive silver axis,It's also more suitable,But only K70 can be selected。 The black axis is too strong and can be directly discharged, unless you are a strong adamant finger and the game time is not very long, otherwise the fingers will be more tired after a long time.