How to learn car wraps? What are the steps

Hello The general process of the film.

1.Interior protection.

In the process of lamination, the solvent of cleaning the glass will seep into the electronic control system of the car without paying attention, resulting in switch failure or even local short circuit, so it is necessary to carefully protect the exposed electronic control switch and speaker of the vehicle by covering the special dashboard cover on the instrument panel. Leather seats and premium seat covers are also fully covered with special seat covers.

2.Glass washing.

The cleaning of glass is related to the basic work of the sun film assembly, and the cleaning is divided into three steps: removing rubber particles and grit from the glass surface; Dust removal and cleaning of glass three times (pay attention to the audio and electronic control system of the car); Wash again before applying the film. Always be careful with the protection of the heating wire when cleaning the rear windshield.

3.Filming. The outer surface of the glass is sampled, and the size is mastered to facilitate the blanking, and the material is not wasted as much as possible. The edges of the crop must be smooth and not uneven, so as to affect the appearance.

4.Stereotypes. The front windshield must be fixed first, and the qualitative method requires "high temperature and high speed", that is, the temperature control button of the heat gun is adjusted to the highest, and the wind speed is also controlled in the high-speed gear, which is quickly finalized.

Generally speaking, the curvature of the rear windshield is also relatively large, and the installation method should be the same as the front windshield, and even the side windows of some models need to be shaped. At present, there are two commonly used baking methods: dry roasting method and wet roasting method.

Experts say that in terms of installation difficulty, dry roasting takes advantage of more space to shrink the membrane in more space, so it is much simpler than wet roasting. In the process of heating, wet roasting only uses a small part of the space to shrink the membrane, so wet roasting is more difficult. In terms of film thickness, the advantage of wet roasting is that it allows the film to be set at one time, while dry roasting is difficult to set thick film at one time, so dry roasting is not suitable for thicker films.

1.School study time, 2-3 months Generally, if you go to school to learn, two or three months of learning is almost, the school's equipment, training consumables are relatively richer, more practical training operations, naturally more comfortable, generally 2 3 months to learn, and then is the accumulation of experience.

2.Physical store learning time half a year - 1 year If you go to a physical store to learn, the business is good and often the film is about half a year to a year, provided that people are willing to teach you, because the physical store receives materials.

3.Of course, whether you learn it in a physical store or in school, you can only truly master this technology if you work hard to learn the technology.

You can come to our school to study systematically, our school is basically a workstation for each person, practical operation, I hope you can.

If you want to learn to apply film, the first step is that you have to be able to wash the car, you can't wash the car, and you can't apply the film.

Car film is a technical work, each process needs to be practiced, you can go to the professional, good environment of auto repair learning, can take the source quickly to improve themselves, but during the study period of the treatment is very low and sensitive, the best way to learn car film is to find a second-hand windshield for practice.

Now the development prospects of the car beauty industry are still very good, it is recommended to learn a complete car beauty technology, and there are still some deficiencies in learning the film alone.

As an indispensable car product for automobiles, car film has many functions, including blocking ultraviolet rays, filtering strong light, protecting passengers in the car, protecting privacy in the car, enhancing car anti-theft, etc., if the body of the car is violently impacted, Wang Zhi car film can protect the car glass from breakage, and will not hurt the people in the car because of glass splashing.

It's okay to study on your own.

1. Before the film, first of all, it is necessary to ensure that the working environment meets the requirements of dryness and less dust, otherwise dust and debris will enter during work, which will affect the effect of the film. It is recommended to wash the car before applying the film.

2. Cover the necessary position of the vehicle, and the internal and external combustion parts should be protected with protective covers, and if there is no special material, you can also choose plastic wrap.

3. Clean the car glass that needs to be filmed, pay attention to the top and edge of the glass, and then wipe the water.

4. The next step is to cut the car film, pay attention to the size of the car film to match the glass. Spray a little water on the surface of the glass, then adsorb a certain thickness of plastic film to the window, and then draw a pattern according to the edges, the template can be a little more than the glass.

5. When the front and rear windshields are filmed, the baking film also needs to be shaped. Cover the cut car film on the outside of the glass, and then use the heat gun to deshape it, this step is also more critical, and it is easy to make mistakes, because the temperature and shaping techniques of the heat gun have relatively high requirements, otherwise improper use can easily lead to blackening of the car film or glass cracking.

1. Learn the front windshield film technology, rear windshield glass film technology, side windshield glass film technology, vehicle glass film technology, window small corner film technology, and special vehicle film technology.

2. Side window baking film technology, front and rear baking film technology, front and rear dry baking technology, front and rear wet baking technology, air baking technology, stretch baking technology, horizontal baking technology, vertical baking technology, dry and wet combination baking film technology.

3. The understanding and use of car film tools, the basics of film knife work, precautions and essentials for film cutting.

4. The understanding of automobile explosion-proof film, the introduction of automobile explosion-proof film, the classification of automobile explosion-proof film, the identification of automobile explosion-proof film, and the selection of automobile explosion-proof film.

Car film is to paste a layer of film-like objects on the front and rear windshields, side windows and sunroofs of the vehicle, and this film-like object is also called solar film or explosion-proof heat insulation film. Nowadays, the automobile explosion-proof film has developed into a very high-tech automotive decoration products, which is usually composed of seven layers: polyester film layer, metal coating, adhesive layer, wear-resistant layer, ultra-thin coating and two safety base layers. Its function is mainly to block ultraviolet rays, block part of the heat and prevent injuries caused by sudden bursting of glass, and at the same time according to the one-way perspective performance of the explosion-proof film to achieve the purpose of protecting personal privacy.

Due to the complexity of the surface shape and installation of automotive glass, as well as people's high standard requirements for the flawless quality of automotive explosion-proof film mounting, automotive explosion-proof film mounting, has become a high-end technical work. The car film master class of our institute not only teaches explosion-proof film film, but also includes body carbon fiber film, body painting film, headlight magic color film, etc., covering various automotive film film processes.

Paint treatment, removal of body accessories, cutting of color change film stealth clothing, posting of color change film stealth clothing, team cooperation baking film, corner treatment, interior color change, detail processing, rhinoceros skin paste, headlight film.

From foundation to independent construction, at least 1 year or more, and the salary of the apprenticeship stage is very low. But if the master is willing to teach, and you are willing to learn, you can gradually participate in the construction process in about 3 months, and maybe one or two months if you are fast.

The methods and steps of car film are as follows:

1. Spread the solar film on the front windshield first, then blow it with a hair dryer to deform it, and smooth the solar film by hand while blowing to make it extend, which can fit the curvature of the glass;

2. Use a special tool to scrape the solar film flat, so that the film completely fits the front windshield. Use a knife to cut the membrane into the desired shape, and then remove the various annual inspection signs pasted on the windshield;

3. Gently take off the film that has been extended and cut the shape, spray the mixture of water and washing spirit on the front windshield, and then wipe all the dirty things on the glass clean, and then spray the mixture of water and washing spirit after wiping it clean;

4. Tear off the adhesive and gently stick the film on the glass stained with water and washing spirit mixture according to the shape cut before. Use a tool to drive all the water and bubbles between the lead film and the glass out of the socks.

Under normal circumstances, the car film is used in this common method and procedure, and it can include three methods and steps at any time.