60 60 plasterboard or mineral wool board ceiling to do

It is a 600 * 600mm board, this gypsum board ceiling and mineral wool board practice is actually similar, the hoisting method of Meiluda mineral wool board is to first use a screw rod to hang down the paint 50 light steel keel first in the indoor lap well, and then use the mobile hook to lap the main keel of the paint keel on the light steel main keel, and then according to the indoor keel ratio, lap paint keel, small keel, pay attention to some hoisting schemes die without the keel or small keel, and finally install the paint edge keel around the indoor wall.

First of all, it is necessary to find a good horizontal position, which is to lay a horizontal line on the surrounding walls, and then determine the height of the ceiling according to the horizontal line.

The plastic gusset is a wooden keel, first drill holes with a percussion drill on the surrounding walls, and install the extended keel, and then install the main keel in the middle; The spacing of the main keel is about 80 cm and is connected with the top surface (with hanging bars). The levelness of the main keel can be adjusted according to the surrounding keels, and this process requires the use of construction lines, which can be raised a little higher in the middle (about a centimeter).

After the keel is installed, you can install the PVC extended edge keel, and then install the gusset.

The above is the basic practice, but it may be a bit difficult for someone who has never done it before. Therefore, it is advisable to find a carpenter master to help you.

Mineral wool board ceilingIt is a kind of ceiling material that is more popular in the market at present, and its biggest feature is that it has good sound absorption and heat insulation effect, and it is rich in patterns and patterns, so it is widely used in the interior decoration of various buildings. Its non-combustible characteristics effectively meet the fire protection needs of building design. So is the mineral wool board ceiling expensive?

Let's take a look at our introduction!

Because the defects of the mineral wool board itself material lead to the appearance of the mineral wool board ceiling looks very rough, so when decorating, some paint and color paste will be used to plug the micropores on the ceiling and increase a certain degree of beauty, but this will cause unnecessary household pollution.

Friends who have purchased and decorated ceilings know that the ceiling ** is generally calculated according to the area of the ceiling to be done indoors and the irregularity of the ceiling when budgeting.

Under normal circumstances, the mineral wool board ceiling within how many square meters will be more expensive than the unit price higher than this ordinary number, for example: the mineral wool board ceiling within 5 square meters is bending resistant to 50 yuan square; After more than 5 square meters, it may be 60 yuan square.

Another very important factor affecting the mineral wool board ceiling is the irregularity of the ceiling, if the interior design is too personalized, then it will bring a lot of inconvenience to the installation of the mineral wool board ceiling, so in this case, the mineral wool board ceiling is more expensive than the ordinary mineral wool board ceiling.

That's all we bring to youMineral wool board ceilingI hope to be able to help friends who need it!

Rock wool board is a more environmentally friendly material, many people use it to make ceilings, so how to install rock wool board ceilings? Let's introduce the origin to you.

1. Grassroots cleaning: The main content of this step beam is to clean up all the items that will affect the installation of the ceiling.

2. Base elastic line: The purpose of the elastic line is to mark the control line and the ceiling elevation standard, and to pop out the keel layout line and the position of the boom suspension point in turn.

3. Installation of hanging bars: The installation position of the hanging bars is determined by the construction drawings. Before installing the lifting bars, it is necessary to embed the angle iron, and apply anti-rust paint on the angle iron to prevent rust. The upper end of the suspension bar is firmly welded with the angle iron, and the lower end is connected with the hanging piece after threading.

4. Primary and secondary keel installation: the main keel is less than one meter, and the main keel hanger is connected on the main keel. The spacing of the secondary keel should be about meters, and it should also be hung on the large keel. In the parallel direction of the main keel, it is also necessary to install a meter of cross-brace keel.

5. Calibration: After the installation of all keels is completed, the installation and leveling work should be carried out, and the elevation should be adjusted in order from the side keel to the auxiliary keel and finally the main keel.

6. Rock wool board installed by Oak Kaishan: It can be installed according to the installation specifications and design requirements.

Mineral wool board ceiling

1. Construction sequence:

Elastic wire mounting boom Mounting keel and accessories Mounting panel.

2. Construction steps:

1) Ceiling measurement pay-off.

The control elevation of the ceiling, the axis plane pay-off is combined with the pay-off of the floor and the pay-off of the wall column. Elevation pay-off and plane control line from the wall, cylinder 500 lines and axis, the ceiling design elevation and plane general form, this work on the one hand for the next step of the work to create conditions, on the other hand, is the existing ceiling situation, such as air ducts, water pipes, electric pipes, structural beams and columns, etc.

2) Ceiling boom installation.

According to the design elevation of the ceiling, the line is elasticated along the perimeter of the wall column surface as the standard line for the installation of the ceiling.

The boom can be made of steel bars with a diameter of 8mm, and one end of the steel bar with a suitable length is welded with the screw rod lap during installation, the lap weld length is not less than, the exposed length of the thread at the end of the boom should not be less than 3cm, and the other end is welded with the L40*40 angle iron, and the angle iron opens a 10mm hole to install the 8mm expansion screw.

According to the large sample drawing, determine the elastic line of the hanging point position, and re-check the hanging point spacing, and the hanging point spacing is 1000 to 1200mm. At the hanging point, the bottom surface of the floor corresponding to the hanging point can be drilled with 12 percussion drills, and the 8mm expansion bolt that is installed with the suspension rod is fixed at the hanging point.

3) Keel installation.

When installing the base keel, the base keel should be connected to the boom with a hanging piece, and the screws should be tightened and clamped. The length of the base keel can be connected by the rod body. The base keel is leveled after installation, and the arching height of the roof should be considered not less than 1/200 of the short span of the room.

The main keel of distribution will be fixed on the base keel through the hook of distribution, and the secondary keel of distribution will be directly stuck in the buckle hole of the main keel.

4) Mineral wool board installation.

After the keel is installed and accepted, start to install the mineral wool board, and wear gloves during installation to keep the mineral wool board clean and clean.

The main advantages of the prefabricated ceiling combination are: the hanger is hidden, and the ceiling surface is flat and stable; Plate-side snap-on connection, easy to install.

Hope it helps.

The gypsum board is made of wooden keel, the mineral wool board is made of light steel, and the gypsum board can be directly hit on the wooden keel with a nail gun, and the density of the keel can be larger.

It depends on the depth and width of the room. Arrange the whole board from one side to the other, and cut the width left at the end of the head. If Party A does not ask for it, it is generally arranged from the top of the head of the first door.

The distance from the top is the lowest level of the pipeline in the roof. Punch the lower sling.

The installation of decorative gypsum board ceiling can be set up according to the material conditions of various places, such as shelving and flattening, screw fixing and adhesive bonding. (1) Shelving flat method: when the T-shaped aluminum alloy keel or light steel keel is used, the decorative gypsum board can be shelved in each grid frame composed of the T-shaped keel, that is, the ceiling construction is completed.

2) Screw fixing and installation method: when the U-shaped light steel keel is used, the decorative gypsum board can be fixed with galvanized tapping screws and the U-shaped medium and small keel. The eye of the needle is tired of my level, and then repaired with the same color paste as the surface of the board.

The light steel keel used in the mineral wool board ceiling is divided into two types: U-shaped skeleton and T-shaped skeleton, and is divided into two kinds according to different loads: upper and non-human. The light steel keel is divided into the main keel, the secondary keel, and the side keel; Accessories include hanging parts, connectors, hanging plug-ins and other materials must meet the design requirements. To put it simply, the construction of mineral wool board ceiling is convenient and fast.

The construction method of gypsum board ceiling is complicated, and it is necessary to scrape putty to do latex paint or other finishes.

1. Paving unit, gypsum board is usually 1220*2440mm specification, which can be cut as needed, and mineral wool board is usually 600*600, which can be assembled as needed. 2. Use, gypsum board is the most commonly used ceiling material, waterproof gypsum board, fireproof gypsum board can be selected according to the need, mineral wool board is mainly used for sound absorption, mostly used in office corridors, office areas, etc. 3. The unit price of gypsum board according to the area is lower than that of mineral wool board.

The gypsum board is called the top is a wooden keel frame structure, the surface is finished with gypsum board, and the mineral wool board seems to be the same as the aluminum gusset ceiling. It is to use the light steel keel as the frame, and the mineral wool board is embedded in the **!

Mineral wool boards are movable. Easy to install, but the service life is no better than drywall.

Mineral wool board is mainly sound absorption, gypsum board can not achieve the effect of sound absorption, the general office building is with mineral wool board ceiling, the cost is slightly higher.

The main difference between mineral wool board ceiling and gypsum board ceiling is that it has a good anti-noise effect.

Mineral wool board generally refers to mineral wool decorative sound-absorbing board. It is made of granular cotton as the main raw material and other additives are cut by high-pressure extrusion, which does not contain asbestos and has good fire and sound absorption performance. There are generally irregular holes on the surface (commonly known as:

Caterpillar) or micropores (needle eye holes) and so on, the surface can be coated with a variety of color pastes (factory products are generally white).

If the humidity is too high, the mineral wool board will deform and fall! It is recommended to use 600*600 high-grade gypsum board.