LETV 2Is there a phenomenon of mobile phone wifi being disconnected?

Dial in ** to enter MTK engineering mode.

2.Enter the project mode, it's all in English, then swipe left on the lower screen and you'll see WLAN and WLAN CTIA.

3.Turn off the wifi, then enter the WLAN, there are three checkable items, check the first one. Go back to the menu of the 2nd step.

4.Then enter the WLAN CTIA, click it again, and there will also be a check, which is also the first check.

If other wireless devices can't connect to this wireless network either:

You can reboot the wireless router or replug the network cable to try it, if it doesn't work, it may be a problem with your network, and you need to find your network operator to check your home network.

If other devices can access the Internet, only the Super TV cannot access the Internet:, follow the steps below to guide the operation:

Step 1: Enter the system interface, restore factory settings and have a try;

Step 3: If the upgrade does not work, consult the user with the following questions:

Whether to enable MAC address filtering, if so, please add the user's MAC address to the router's allowlist.

The name of the wireless is not in Chinese, please change Chinese to English letters and numbers.

1. Check whether the mobile phone is in arrears, the mobile phone in arrears cannot be connected to the data network and needs to be recharged.

2. If the network fails to refresh due to the delay of the travel network, you can turn on the airplane mode of the mobile phone, turn it off after five seconds, and then reconnect to the network or restart the mobile phone.

3. If the network settings are not set well, you can call the operator to which the mobile phone card belongs, and ask the customer service to send the relevant data of the Internet settings and set it according to the prompts. Old.

4. If you are connected to a wireless network, then you need to check whether the mobile phone wifi password input and the wireless router's Internet access settings are correct, and whether other devices can access the Internet through the wifi.

5. Turn on the power-saving mode or set the screen off in the wifi settings to automatically turn off the wifi, go to the wifi interface and click the three dots in the upper right corner, and then click "advanced" to view the page inside to set it.

It should be that you turn on the power-saving mode or set the screen off to automatically turn off the wifi in the wifi settings, go to the wifi interface and click on the three dots in the upper right corner, and then click "advanced" to check the page inside to set it.

1. First of all, right-click the wireless icon in the lower right corner of the desktop to enter the network sharing center interface.

2. Then, click "Change Interface Card Settings" on the Network Sharing Center interface.

3. Next, right-click "WLAN (i.e. your WiFi interface card)" and right-click "Properties".

4. In the "WLAN" attribute window bar, find the word "Configuration" below it and click it.

5. Finally, enter the "Power Management" interface in the newly opened window, remove the tick of "Allow the computer to close this device after it is turned off to save power", and then click "OK".

6. That's it,Win8 in hibernationWifi uninterrupted network setting has been completed,The next time the computer sleeps, you don't have to worry about WiFi will be disconnected。

The WiFi settings of Android phones have [Keep Wi-Fi connected while asleep], and if you change it to [Always connected], you won't disconnect the WiFi after turning off the screen. As shown in Fig

First: After the screen is locked, it is necessary to set the wifi without turning on. In wifi, click on the mobile phone menu button to select high-end, there is. The system sets the Wi-Fi advanced settings, keeps the Wi-Fi connection in the sleep state, and selects Always.

Go to Settings - Wi-Fi - Advanced Wi-Fi Settings - Keep Wi-Fi connected in sleep - select the Always option.

This is the setting of the Android system. In order to save electricity.

You can use the power control software to not sleep when you need to stay connected.

You can check the check in the wifi settings of your phone to always keep the wifi connected in the dormant state, and it will stay connected after the check is successful.

Hello, if you choose to keep the waln wired, it will not disconnect after hibernation.

We hope you find the above reply helpful.

If the mobile data is disconnected, then turn on Settings, select Mobile Network Settings, and select Always-on Data Service.

If the wifi is disconnected, then, open the settings, select WLAN, click on the thing with three dots in the lower right corner, and select Advanced. There is a Wi-Fi connection that stores Wi-Fi in the sleep state, select Always.

This seems to be designed to save electricity.

Hibernation is the same as the shutdown state of the computer, you can power off the computer, at this time the computer is to temporarily store the memory data to the hard disk, the next start directly from the hard disk will restore the temporary data to the memory, so that the starting speed is very fast, the standby is the computer is in the power-saving mode, all the devices stop working into the most power-saving mode, if you want to broadband my world in the computer standby state of the network uninterrupted network, you can try to manage the power in the properties of the network card Allow the computer to turn off the device to save power Check it, if you want to sleep and also uninterrupt the network, it is impossible to do it, because the calculation is all powered off after sleep.

If the wifi signal of your mobile phone is particularly poor, it may be because of the design of LeTV to stick the wifi antenna to the plastic back cover, if the antenna is blocked when used, the signal will be weakened or disconnected. You can directly press the wifi antenna of the back cover first to ensure good contact, and then press the entire back cover back, but the place where the back cover is close to the camera is glued with tape.

Let's see if their wired connection is stable, if the wire is stable, then the fault point is only in the wireless part of the router and your phone. Then ask other people around you if the connection is stable, other people's stability means that there is a problem with your phone or the wifi signal that reaches you is unstable. Other people's are not good, that means that the router may have a problem with the wireless transmission module, and it needs to be reset and restarted.

1.The router is not good, 2There are too many connected phones, causing the router to be unstable, 3The internet speed is too poor, resulting in frequent inability to access the Internet.

The signal reception of the mobile phone is not stable, and this situation may be related to your router, and it can also happen if your router has a password.

First of all, you make sure that your home network is connected and that you are not connected to your mobile phone. whether the computer is connected to the Internet; If you can't restart the router.

2. If the computer can access the Internet, the mobile phone cannot; Check whether the SSID number of the wireless router is in Chinese; If it is changed to letters and numbers; Mobile phones sometimes can't effectively recognize Chinese:

3. If the above cannot be solved: we set a static IP for the mobile phone

The edge of the wifi or the unstable wifi network may be the most likely thing about your mobile phone system (if you have swiped the system).

I don't know if you use a router or wifi computer software.

I'll directly summarize the computer software wifi sharing Jingyou Sun Ling is similar.

There are several possibilities:

First, the network signal of the computer you created the wifi hotspot yourself is not good.

Second, your computer's driver is not updated in time, resulting in incompatibility.

Third, the campus network dial-up Internet access.

Fourth, the wireless network card model is not supported.

Fifth, you're blocked by defense software, etc.

For specific tutorials, please refer to::wifigx/thread-2742-1-1.

There are several reasons for this:

1. Reset network settings.

It is also possible that there are some problems with the system if the wifi signal is not good, and some problems can be solved by restoring the network settings.

2. The mobile phone case affects the WiFi signal.

Most mobile phone users will wear a protective case for their mobile phone, but some third-party protective cases, especially metal protective cases or metal bezel cases, can affect the WiFi signal.

3. The router is closed.

If you rule out the cause of the phone itself, you might as well see if there is a problem with the router, and you can try to restart the router.

4. Upgrade the latest system.

Firmware updates often include fixes to various bugs and errors, and sometimes optimizations and enhancements to this part of the network. If the wifi signal is not good, and you stay in the older version, don't let it upgrade to the latest system to try.

In this case, it is recommended to reconnect to the wifi once, you can open the [Settings] in the mobile phone in turn, then open [General], then click [Restore], and select [Reset Network Settings], so that the device will automatically restart, re-identify the new network, and enter the wifi password.

The specific steps are as follows:

1. Find and open [Settings].

2. Click [General].

3. Click Restore

4. Click [Reset Network Settings].

Dear users, hello:

1. First of all, make sure that the network is normal, and whether the computer can be networked; If you can't restart the router.

2. If the computer can access the Internet, the mobile phone cannot; Check whether the SSID number of the wireless router is in Chinese; If it is changed to letters and numbers; Mobile phones sometimes can't effectively recognize Chinese:

3. If the above cannot be solved: set a static IP for the mobile phone;

4. The wireless router supports between 15-20 wireless devices; When the maximum number of connected wireless devices is exceeded, even though it is connected to the wireless; But it's wireless; At this time, you can unplug the wireless router; Turn on the wireless router after 10 minutes.

2.Then, when you see the wifi signal that you are currently connected to, click on the small blue circle arrow on the far right.

3.Click "Ignore this network". Then, the wifi connection of the mobile phone will be disconnected, so that the mobile phone will not automatically connect when you click to connect to the signal source again, but will re-enter the connected wifi password, that is, the mobile phone will re-identify the network once, so that you can achieve the effect of emptying the original network configuration.

4.Of course, if you want to clear it more thoroughly, you can open Settings ---General --- Restore in turn, and select "Reset Network Settings". In this way, the device will restart, and after the restart, all previously connected networks will not be saved, but will be recognized as a new network, and the wifi password will be entered to connect.

Question: LeTV's mobile phone is even a wife, how can it be that you can't access the Internet?

Question: No. Answer: Many people will be in this situation with you. People around you can access the internet on their mobile phones. Not on your own mobile phone. Then you can only reset the router after factory reset and reset the router.

Remember your broadband account password before you can set up your router. There is a button on the back of the router to do a factory reset.

wifi

If it is wifi, it is recommended that you click Settings - WLAN - Advanced Settings to select Never sleep, and click Settings - WLAN - to find this wifi, click the small arrow on the right, do not save the network, re-enter the password to try, you can also try to restart the router to try, if this problem still occurs, it is recommended that you try the wifi network in other environments to see if this problem still occurs.

GPRSIf it is a data traffic network, it is recommended that you click Settings - Mobile Network - Access Point APN - Reset to Default and then try again, data Internet access and the surrounding environment, weather, location is also related, it is recommended that you try again in other places with a slightly better signal.

Can't get online" This question is very general, I try to guess the problem you may encounter, I suggest you try the method to operate and see:

1It is recommended that you put this SIM card into another mobile phone to check if you can access the Internet.

2. If you can't access the Internet, please ask your carrier if you are in arrears.

3If it can be used, please put in your Xiaomi phone, turn on the data traffic switch, and reset the default in Settings - Access Point APN, and then restart the phone to try again.

4If you still can't surf the Internet, it is recommended that you back up your data, enter recovery to clear all data (turn off, press and hold the volume up + power button to enter recovery), upgrade your phone to the latest development version of the system, don't install apps that require root access for the time being, and see if it can be restored to normal.

WiFi internet access.

You can follow the methods below to set up your phone:

1.Click Settings --WLAN, select the arrow next to the name of the network you want to connect to, select Don't save the network, and re-enter the password.

2.Restart your phone and router.

3.Still no, it is recommended that you try whether the wifi in other environments can work normally.