How to adjust the touch screen time on the Black Decker range hood

Black & Decker range hood.

Adjust the time directly in the control panel.

The specific steps are as follows:

1. Find the Settings button on the control panel.

2. Press and hold the setting button for 3 seconds.

3. Enter the time setting mode.

4. After entering the time mode, the first thing to adjust is the hour by default, pressing the steaming button is to add the hour, and pressing the soup button is to decrease the time.

5. Press the setting button again to adjust the minutes.

6. Press the steaming button to add minutes, and press the soup button to subtract minutes.

7. After adjusting the time, press the setting button to confirm the operation.

In the shutdown state, press and hold the icon of the clock for about 5s to enter the adjustment menu, the large air volume and the small air volume represent the addition and subtraction respectively, after adjusting the hour, then press the clock icon to enter the minute adjustment, in fact, this clock key is equivalent to the menu key, I just adjusted.

Usually there is a "set" button on the switch icon, standby state (that is, the motor is not working), press the "set" button for 3 seconds, the "+ button or "left motor" and "right motor" will flash, at this time press the "+" key or "left motor" and "right motor" to adjust the time.

Black & Decker range hood adjusts the time and operates directly on the control panel, and the specific operation steps are as follows: 1. Find the setting button on the control panel. 2. Press and hold the setting button for 3 seconds.

3. Enter the time setting mode. 4. After entering the time buried car mode, the first default adjustment is the hour, pressing the steaming button is to add the hour grinding, and pressing the soup button is to reduce the hour. 5. Press the setting button again to adjust the minutes.

6. Press the steaming button to add minutes, and press the soup button to subtract minutes. 7. After adjusting the time, press the setting button to confirm that the operation is finished.

Hello, I would be happy to provide you with a solution. Dear, hello, the debugging steps of Baibaide range hood are as follows:1

Adjust the speed of the fan: first turn on the switch of the smoke machine, and then select different wind speed gears through the control panel or remote control to observe whether the air volume meets the requirements of Huikai. Generally speaking, the high-grade wind speed is suitable for the situation of large oil smoke, while the low-grade wind speed is suitable for daily use.

2.Adjust the brightness of the lighting: The lighting function of the hood can help the kitchen to be brighter and easier to cook.

Depending on the need, the lighting brightness can be adjusted through the control panel or remote control to achieve the best results. 3.Adjust the duration setting

Some smoke machines have a timer function, which can automatically stop working. Set the appropriate time according to the setting method in the manual to ensure safe use and power saving. 4.

Adjust the noise: Since the smoke machine will make noise when working, the noise needs to be adjusted. Noise generation can usually be reduced by means of reducers, installation of soundproof cotton, etc.

The above is the debugging method of Baibaide range hood, dear, you have a good front cover, be sure to read the manual carefully before operation, and operate in accordance with the regulations to ensure the safety and effect of use. If you have any questions, you can continue to communicate with Sun Han

Hello, 1.First of all, please check whether the power cord of the range hood is connected properly and turn on the power switch. 2

Next, please check whether the exhaust pipe of the range hood is installed correctly, and tighten the remorse screws at the exhaust pipe interface firmly. 3.Then, please check whether the filter screen of the range hood is installed and install the filter inside the filter room of the range hood.

4.Next, please check whether the exhaust outlet of the range hood is installed correctly, and tighten the screws at the exhaust outlet interface firmly. 5.

Finally, please check that the control panel of the range hood is installed correctly and install the control panel inside the control panel of the range hood.

Hello, the commissioning of the range hood can be carried out by following the steps below:1Installation Location:

First of all, determine the installation location of the range hood, which should generally be selected above the stove, and ensure that the distance from the imitation tan stove meets the safety requirements. 2.Power Wiring:

Properly plug the power cord of the range hood into the power outlet and make sure the wiring is firm and reliable. 3.Duct Connection:

Connect the exhaust duct of the range hood to the outdoor exhaust port to ensure that the duct is unobstructed. 4.Functional debugging:

a.Power switch: Turn on the power switch of the range hood to confirm whether it is working normally.

b.Adjust each gear: Try different gear adjustment according to your needs, press the source button to observe the air volume and noise.

c.Lighting function: Test the lighting function of the range hood to confirm whether the light is on and working properly.

d.Key Operation: Test other key operations, such as delayed shutdown, timer function, etc.

5.Airflow adjustment: a

According to the size of the kitchen and the actual needs, choose the appropriate air volume level. Generally speaking, you can choose a high gear when high temperature and high power, and low gear can be selected when low temperature and low power. b.

If the range hood is equipped with an air volume adjustment switch, it can be fine-tuned according to the actual situation. 6.Noise Detection:

Pay attention to the noise of the range hood at all gears to ensure that the noise is within a reasonable range. 7.Cleaning and Maintenance:

Clean and maintain the range hood regularly, including cleaning the oil mesh, replacing the activated carbon filter, etc.