Use the wireless relay function to disconnect the network, unplug the wireless relay router, and plu

You should have caused a conflict between the IP addresses of the router of the relay and the main router.

How to set up two wireless routers for wireless relay:

The first wireless router:

1.First, log in to the router that is connected to the Broadband Modem.

2.Set the SSID number and Channel in Wireless Settings - Basic Settings, and set the fixed channel number.

3.Set the wireless signal encryption information in the Wireless Settings - Wireless Security Settings to record the SSID, channel, and encryption settings of the wireless router after setting.

Second Wireless Router:

1.Log in to the second wireless router that requires a trunk.

2.In the network parameters - LAN port setting, change the IP address to be different from the first router (to prevent IP address conflicts), for example, save, the router will automatically restart.

4.Select the SSID number of the first router in the list of scanned signals and click "Connect".

5.Set the channel to be the same as the first router channel. At the same time, set the encryption information to be the same as the first router, and click "Save".

6.Shut down the DHCP server. In the DHCP server, select Disable, save, and restart the router.

7.At this point, the first wireless router and the second wireless router have successfully established WDS.

OK. The signal received by the wireless relay of the wireless router is the same as that of the WAN port connection network cable, which can be used directly by the network cable of the LAN port for the computer.

One AP mode, which is relatively simple and requires a network cable, and one WDS mode, which requires hardware support.

A router is a device that connects various LANs and WANs on the Internet, and it will automatically select and set routes according to the situation of the channel, and send signals in the order of the best path.

At present, routers have been widely used in all walks of life, and various products of different grades have become the main force to realize the internal connection of various backbone networks, the interconnection between backbone networks, and the interconnection between backbone networks and the Internet. The main difference between routing and switching is that the switch takes place at the second layer of the OSI reference model, while the routing takes place at the third layer, which is the network layer. This difference determines that routers and switches need to use different control information in the process of moving information, so the way they implement their respective functions is different.

Summary. The wireless router relay is set, and there is no relay signal after setting, even if there is, you can't access the Internet Reason: DNS settings are wrong.

The secondary router uses the DNS of the primary router. [Main Router Settings] Enter the settings interface of the main router, and then click [Running Status] in the left option bar, and you can find the DNS server in the WAN port status bar, there are two in total, the primary DNS and the alternative DNS server, and record them.

Why can't I connect to the network after unplugging the relay router after the wifi relay?

Dear, I've seen your question, wait a minute!

The wireless router relay is set, and there is no relay signal after setting, even if there is, you can't access the Internet Reason: DNS settings are wrong. The secondary router uses the DNS of the primary router.

[Main Router Settings] Enter the settings interface of the main router, and then click [Running Status] in the left option bar, and you can find the DNS server in the WAN port status bar, there are two in total, the primary DNS and the alternative DNS server, and record them.

Set the sub-router] click [DHCP Server] --DHCP Server Settings], change the [Address Pool Start Address] to [Address Pool Start Address] to . [Gateway] Fill in the IP address of the main router, that is. The primary and alternate DNS servers fill in the previously recorded addresses to save and reboot the router.

After turning off the relay router, why can't the main router go online?

Just restart it.

The possible reasons for the unstable relay of the wireless router and the drop of the connection to the wifi are as follows:

1. Poor heat dissipation leads to overheating of the chip, which affects the working performance.

2. Electromagnetic interference.

3. The network cable of the router is loosely connected.

4. The router is aging.

The solution is as follows: Mu Sui sedan chair.

2. Try not to use wireless mice and keyboards, and do not use wireless devices such as set-top boxes.

3. Keep away from microwave ovens and cordless radiation sources. If possible, you can replace the 5GHz router to avoid the congested GHz frequency band.

4. Check whether the connection between the WAN port and the LAN port of the router is loose, and reconnect to ensure a reliable connection.

5. Replace the router.

It is possible to connect a repeater after the router has been relayed. And this device can make the wireless signal stronger.

Q: Is it possible to connect a repeater after a wireless router relay?

Answer: Yes, the repeater is a device that connects network lines, and is often used for two-way work of physical signals between two network nodes. The repeater mainly completes the function of the physical layer, which is responsible for transmitting information bitwise on the physical layer of two nodes, and completing the function of replication, adjusting and amplifying the signal, so as to extend the length of the network.

Due to the loss, the power of the signal transmitted on the ** road will gradually attenuate, and when the attenuation reaches a certain level, it will cause signal distortion, so it will lead to reception error, and the repeater is designed to solve this problem.

IFI repeater.

The working principle is to send and receive the superior WiFi signal, maintain the attributes of the signal and continue to send and receive the task after amplification, and complete the transmission relay of the WiFi signal. It is often disconnected, which is related to the strength of the relay signal and the working state of the repeater itself.

1. Intermittent network disconnection, that is, when it is still working normally, it means that the configuration parameters are positive and high. When the wifi repeater is in the working state of continuous shielding or ruler power-on, when its physical condition is not very good, it will stop working due to the long working time and the temperature is too high, and the protection state will stop working;

2. When the working state is stopped, the temperature of the circuit device will drop, and when it is lower than the temperature protection value, the circuit will re-enter the group to enter the working state, and the network will be connected again. If this is the case, you can help it to verify the cooling, or simply replace it with a repeater.