How to make retro floor paint, how to make floor paint?

1. Plain land treatment: the cement plain ground must be thoroughly dried, the ground must not be oiled, the ground cannot be cleaned with water, and the grinding, repairing and dust removal work should be done according to the condition of the plain land;

2. Mix the A component and B component of the retro floor paint according to the weight ratio of 2:1, use the electronic scale to batch, pay attention to the ingredients should not be too much, and the mixed material can be used for about 20 minutes at room temperature of 20 minutes.

3.The retro paint can be coated 3-5 times to form a film, and the first and second coats will be absorbed by the cement, and the coating distance of each coat is more than 5 hours (be sure to make sure that each time is thoroughly dried before coating the next one). Each time the material should not be more than 6kg, how much to adjust and how much to use, and if it is not used up 10 minutes after batching, it will solidify in the barrel.

4.If the surface texture is high, it should be polished after each paint is dried (local spot grinding), and the last top coat of paint does not need to be polished. The construction can be completed 24 hours before the person can be put on the person, and 72 hours after the heavy pressure. (25 shall prevail, and the opening hours of low temperature shall be moderately extended).

5. The new mortar cement leveling ground (4cm-5cm thickness concrete leveling) needs to dry for more than 28 days.

6. It is best to apply retro paint 3-5 times, and each time it cannot be painted too thickly, so that the effect is better!

7. There are 2 rollers for construction, and it is recommended to use chemical fiber or cotton thread rollers with good quality to avoid the severe hair loss of the roller during construction and the phenomenon affects the appearance (use transparent tape to glue off the wool that is easy to fall off before the drum is used).

Antique floor paint, also known as retro floor paint, is just called different, antique floor paint ** is 38 yuan kg, 1kg to do about 3 square meters, a square material cost is about 12 yuan, the construction cost varies depending on the size of the area and the foundation condition. Here I want to emphasize that the antique floor paint must be made on the cement mortar floor in order to make that transparent and ethereal feeling. Not on any other ground.

The construction is carried out according to the characteristics of its own use. To avoid the effects of humidity.

1. The main base material.

1) Polyurethane resin: It is made of isocyanaester and polyester, polyether, epoxy resin, castor oil or its processed products (oxidized polyglycerol alcoholic hydrolysate) hydroxyl thermoplastic polymer (such as polypropylene ester resin containing b-hydroxyethyl group, chloroacetic vinegar copolymer resin containing hydroxyl group), acetate butyl cellulose and other formulas, made of many varieties of polyurethane coatings. For example, TDI or MDI is used in combination with polyether as the main binder for elastic floor coatings; HDI is used in combination with polypropylene resin containing B hydroxyethyl group, which is the binder of high-grade floor coatings.

2) Epoxy resin: When epoxy resin is used in floor coatings, epoxy resin is used as a seamless ground coating material on the floor, and it is the main binder of water emulsion exterior wall coatings.

3) Acrylic resin: It is composed of resin made of acrylic ester and other alkene monomer copolymerization, through the selection of different resin structure, different formulas, production processes, solvents and additives, can be made into solvent-based, water-based, powder and solvent-free and other varieties.

2. Secondary film-forming substances.

The secondary film-forming substance is also an important part of the enamel coating film, but it cannot be separated from the main film-forming substance to form a coating film alone. This ingredient is the pigment used in paints. Adding pigments to coatings can not only improve the performance of the coating film, but also increase the variety of coatings.

3. Auxiliary film-forming substances.

The auxiliary film-forming substance cannot be enamed, or is not the main body of the coating, but has a great impact on the film-forming process (construction process) of the coating, or plays some auxiliary role in the performance of the coating film.

2) Auxiliary materials: with film-forming substances, pigments and solvents constitute coatings, but generally in order to improve performance, some auxiliary materials are often used, and there are many auxiliary materials in the coatings, each with its own specialty, but the amount is very small, generally a few percent to a few thousandths or less. Although the dosage is small, the effect is significant.

According to the function of auxiliary materials, it can be divided into driers, plasticizers, wetting agents, ultraviolet absorbers, etc. Driers and plasticizers are used in large quantities. The following is a description of the composition, characteristics or use of the type of floor paint.

The types of floor paint are mainly divided into: polyurethane and epoxy. Polyurethane advantages:

The performance is stable, it is less affected by air humidity and ambient temperature, it is not easy for workers to have problems in construction, and the surface effect is good. Disadvantages of polyurethane: it is difficult to make high-solid coatings and solvent-free coatings, a large amount of solvents need to be added, and the smell is relatively large.

Advantages of epoxy: It is easy to make high-solids coatings and solvent-free coatings, with low odor, low product toxicity, high overall strength and excellent performance. Epoxy disadvantages:

When applying under high humidity conditions, the topcoat is prone to matte, and the temperature is lower than 10, and the paint is not easy to cure and dry. In recent years, water-based coating technology has been quite mature, not only environmentally friendly and non-toxic, but also excellent performance, even at low temperatures can be cured and dried as usual.

Construction steps: determine the strength of the base surface, flatness, and moisture content of the substrate: the cement strength is required to be at least C20 or above (if there is a sandy floor, the ground strength needs to be strengthened with a coating); The flatness of the ordinary ground is required to be within 5mm (the potholes need to be filled with solvent-free epoxy paint and quartz sand, and the high place should be polished off when the base surface is polished); The moisture content of the substrate is 6, generally not more than 10, the construction of oily materials must pay attention to this, when the ground is wet, the coating layer is not adhesion, and the ground will be delaminated, if it is a water-based coating, as long as the ground is free of open water.

Ground grinding: Use the diamond grinding head to polish the ground as a whole to a certain roughness to increase the adhesion between the paint and the ground. In the case of emery floors, the floor needs to be shot blasted and sandblasted, or directly primed with a solvent-free epoxy primer or a non-ionic water-based epoxy primer, a high-adhesion material.

After the ground is sanded, clean up the dust.

Primer (to increase the adhesion between the ground and the paint): Mix the two-component primer according to the specified ratio, stir it well with a mixer, and use a trowel or roller to apply. After the primer is cured and dry, the secondary coat can be applied.

Batch scraping medium coating (to increase compressive strength and further leveling the ground): mix the two-component medium coating according to the specified ratio, add a certain proportion of quartz sand, stir it well with a mixer, and use a trowel to scrape it evenly. After the middle coating is cured and dried, the putty layer can be applied.

Batch scraping putty layer (filling the gap between the middle coating sand and sand): mix the two-component middle coating according to the specified ratio, add a certain proportion of quartz powder or talcum powder, stir well with a mixer, and use a trowel to scrape evenly. After the middle coating is cured and dried, the surface layer can be constructed.

Surface layer (increase decorative effect): The surface layer is divided into thin coating type and self-leveling type, the thin coating type uses a roller or spray gun construction, and the self-leveling type uses a trowel to scrape. Mix the two-component topcoat according to the specified ratio and stir it well with a blender.

After the topcoat is dried and cured, it needs to be cured for 3-5 days before it can be applied to people and machines.

If you have any other questions, you can contact: 13815247427

Shanghai Weiwei Chemical Technology ****-OVG brand (top ten brands of floor coatings in China).

Floor paint: Applicable places: epoxy resin flooring is widely used in electronics, electrical appliances, hardware factories, machinery factories, chemical factories, pharmaceutical factories, and laboratories. Parking ground level.

Surface form: glossy, semi-glossy, matte, orange peel.

Construction technology: 1. Waterproof treatment: the ground on the first floor needs to be waterproofed;

2. Plain land treatment: polishing, dust removal and repair according to the condition of the plain land;

3. Epoxy primer: apply an epoxy sealing primer with strong penetration and adhesion to enhance the adhesion of the base surface;

4. Epoxy mortar: add an appropriate amount of quartz sand with epoxy medium coating, evenly level, and construct several roads according to actual needs.

5. Epoxy putty: according to the actual needs of the construction of several roads, it is required to be smooth and without holes, no knife marks and sanding marks.

6. Epoxy topcoat: Epoxy topcoat is painted, and the overall surface is bright and clean after completion, with uniform color and no hollowing.

7. Construction completion: 24 hours before the person can be on the road, 7 days after the heavy pressure (25 degrees shall prevail, low temperature opening hours need to be moderately extended).

1. Ground grinding: Use a grinder to polish and level the parts of the ground such as cement slag above the ground to remove the ground ash. Other treatment measures are used for loose and oily ground.

2. Primer: After the concrete substrate is processed and cleaned, the primer (roller coating or brushing) can be carried out, and the roller coating or brushing should be even.

Uniform, consistent thickness. The primer has a certain water vapor permeability, which can enhance the strength of the substrate and increase the adhesion of the coating to the substrate.

3. Intermediate coating: Quartz sand and quartz powder are added to the prepared water-based epoxy coating (intermediate coating) to form a water-based epoxy mortar, and it is evenly coated with a trowel to increase the thickness and compressive strength of the coating.

4. Batch supplement: After the middle coating, the floor is polished with sandpaper, and the putty composed of water-based epoxy paint (medium coating) and quartz powder is constructed according to the actual needs, and it is required to be smooth and no holes, and there is no batch of knife marks and sanding marks.

5. Putty batch supplement: the use of primal coating materials is deployed according to the proportioning method of primal coating materials, and the surface can be directly coated in polishing without adding water.

layer is scraped onto the layer. If necessary, you can appropriately add finer quartz powder or heavy calcium powder to make up, and polish it as a whole with fine sand disc paper after the batch is finished, and the reference amount of the material is supplemented.

6. Topcoating: Applying the water-based epoxy floor coating to the surface coating, the surface coating roller coating is applied twice, and the overall ground gloss is required to be soft, clean and uniform after completion.

1. No empty drums.

7. Maintenance: It takes 24 hours for the surface layer to be dry, and it should be closed during this period, so as not to affect the clean and smooth effect of the surface. 3D can be uploaded.

people, 7 days after the completion of maintenance can be officially put into use (25 shall prevail, low temperature needs to be moderately extended).

The foundation of the plain land shall be based on the cement powder surface or the grinding stone floor, and the construction plain land shall be kept dry and clean before construction.

Before construction, it needs to be kept clean, and if there is any debris adherence, it needs to be removed; Stir well with the main agent before use; Mix the main agent and hardener according to the correct ratio and stir thoroughly; Use a roller or trowel to evenly coat and mix the material, and the construction of the material needs to be completed within 30 years; The construction handover should be handled at the handover place; After the completion of the work, 24 people in the rear, 72 can be pressurized.

Precautions and key points for floor paint:

The use of floor paint in daily life is very extensive, and the decorative sense of floor paint is very strong. Therefore, it is also used in home decoration now. What is the practice of floor paint is a problem that many owners are more concerned about when decorating, in fact, the practice of floor paint is not difficult, as long as it is in accordance with the standard method, the construction will not be a quality problem.

The construction process of floor paint is:

1. Treat the foundation ground well to achieve no oil stain and no cracking;

2. Mix the strengthened asphalt filler and roll the foundation ground with a primer;

3. Coat the surface layer with stirred paint and apply scraping oil;

4. Epoxy mortar can be applied by scraping and trowel coating.

Floor paint is manufactured by a variety of different substances through multi-process production processes such as mixing, dissolving, and dispersing, and is mainly divided into decorative floor paint, heavy anti-corrosion floor paint, and heavy-duty floor paint. Floor paint has the characteristics of bright, real, beautiful, wear-resistant, waterproof and anti-corrosion. The self-leveling properties mentioned in floor paints mainly refer to topcoats, primers and secondary coats, which are the same as other types of floors.

The quality of the self-flowing flat paint is the key to the appearance and use of the epoxy self-leveling floor. The construction of epoxy artesian plane paint mainly takes the form of trowel batch scraping, and gently drives the artesian plane paint through the toothed side of the trowel to create power and then let the artesian plane paint level by itself.

One step of grinding, the second step of repair and dust removal, and the third step of epoxy resin primer coating.

The best way to use epoxy resin floor paint should be done in accordance with the general industrial floor construction technology, which is also the most economical and practical.

The proportion requirements of each house are not the same, add the dilution dose between %5-10%, strictly according to the proportion on the instructions to deploy, and then stir evenly, put it for half an hour and wait for curing before coating, the thickness of the bottom and middle surface coating is not the same.

Step 1

1. Base surface treatment, polish the ground, dispose of the dust and impurities on the ground, and keep the ground as smooth and clean as possible;

2. Roller brush primer to improve the adhesion ability of the middle coating and the base surface;

3. The mortar is coated in batches, and the layer mainly plays the role of compression;

4. Scrape putty in batches to improve the bonding ability of the middle coating and the top coating;

5. The top paint, roller brush surface coating or trowel scraping floor paint, can also spray surface coating or surface layer to do anti-slip process.

Commonly used are epoxy, anti-corrosion, polyurethane, elastic, anti-static, anti-slip, load-bearing and other seven categories. The characteristics can be seen according to their names, such as epoxy, the base material is epoxy resin, which can be constructed on the original base surface, and it is cost-effective, and the anti-corrosion and wear-resistant properties are also good.

Question: There is a frying workshop in the soybean products workshop, and what kind of floor is suitable for the pressing workshop.

Epoxy self-leveling, water-based polyurethane mortar flooring, sealing and curing agent flooring can meet the wear-resistant, anti-slip, anti-corrosion resistance of the food factory floor, our flooring materials are water-based materials that meet environmental protection requirements, non-toxic and odorless.

Question: Tofu water contains brine and corrodes the ground, because tofu water is hot, and there is brine corrosion, I don't know what to do for the floor, and another to make fried soy products, the ground is seriously oily, I don't know what to use.

Ask how much is a square meter.