How to use Heat Fast? How to use it when it heats up quickly

First of all, make sure that the hot water bottle is filled with water, so that the heat pipe of the electric heating rod is completely immersed in the water, plug in the plug to boil the water, wait until the water boils, unplug the plug, wait for 1 minute for the heat to cool down quickly, take it out, and put it in a safe place.

How to use the water boiler when it heats up quickly.

One. First of all, prepare the water utensils and water, and make sure that the water in the kettle, basin, and bucket is enough to submerge the heat pipe that heats up quickly, and the heat pipe of the electric heating rod must be completely immersed in the water. Two.

Plug the hot plug into the household power supply, start boiling water when it is hot, unplug it when the water is hot or boiling, wait for 1 minute for the hot to cool down quickly before taking it out, and put it in a safe place of metal or wood products. Notes: a

The water must be prepared first, and then it can be heated quickly and not dry.

Heat up fast – precautions to heat up quickly boiling water can of course be drunk (the same principle as an electric kettle), but beware:

1.Make sure that the water container and the hot container are clean and free of rust, etc.

2.The water in the container must not be overheated quickly, and it cannot be heated quickly, otherwise it will burn out quickly.

3.Once the water is boiling, don't take the heat out of the water as soon as it is boiled. Unplug the electric plug and wait for the water to cool down before taking it out quickly, because the temperature is still very high at this time, and it is easy to burn out if it heats up quickly.

4.Unplug the electric plug when the water is boiled, because the water boils for too long, which will cause the aging of the water and the formation of harmful substances. Therefore, healthy, human-like water should be fresh.

In addition, if the water is left for too long after boiling, it will also become aging water, and the toxic substances in the aging water will increase with the increase of water storage time. Therefore, it is best to drink the water that was boiled on the same day.

"If it is dry burned in the air, the heat is not easy to dissipate, the metal outer tube will be scorched quickly, and even the heating wire in the tube will be burned off, so the "hot fast" should be put into the liquid first, and the liquid should be submerged in the heating spiral at least (the handle and wire can not be immersed in the liquid), and then turn on the power supply.

After heating, you should also disconnect the power supply first, and after a while, after the temperature of "hot fast" is reduced, then take it out of the liquid and wipe it dry. In addition, because the heating wire in "Heat Up Fast" is a filament made of nickel-iron alloy, it is generally brittle and easy to break. Therefore, "hot fast" should not be violently vibrate, if there is limescale or buildup on the surface, you can use a small brush to gently brush off, do not hit with a hard object or scrape with a knife.

"Once the wire is broken, it cannot be repaired, only a new one."

Fill the boiling water bottle with water, the water must be full, so that the heat pipe of the electric heating rod is completely immersed, and when it boils, you don't need to wait until the light goes out, you can hear the sound of the water boiling. After use, rinse it with cool water and put it in a ventilated place to be safer.

Before use, be sure to check whether there is an alarm device. Whether the line is aging and whether the method is correct. Fill the kettle with water, put it in the heat quickly, plug it in and boil the water.

Boil water for about 15 minutes, unplug when the alarm siren is sounded, wait for 1 minute to cool down quickly, take it out, and put it in a safe place.

In fact, it is still very safe to use it to heat quickly, not to mention that your heat up fast power is not very large.

It's easy to use:

Fill the kettle with water (at or slightly below the mouth of the bottle), heat it up quickly, plug it in and boil it.

About 15 minutes, when the alarm siren is fast hot, unplug it, wait for 1 minute to let the heat cool down quickly, then take it out, and put it in a safe place. If there is no alarm, you can judge whether it has been boiled according to whether there is boiling boiling water gushing out of the bottle mouth.

Precautions: The most important thing is to be present when boiling water, otherwise it is very dangerous, because after the water is boiled, the iron has been heating, resulting in the evaporation of the kettle and the water will be reduced, and when the kettle is empty, it will lead to fire and other dangers! That's the most important thing, just remember that.

Everything else is the same as any other electrical appliance.

Plug in the water and plug it in, but it should be noted that the water must cover the iron core that heats up quickly. Otherwise, be careful that it bursts... It's a bit dangerous. 、、

Fill the kettle with water, put the heat in it quickly, plug it in, the water boils, and he will ring on his own.

After all submersion in water, the electricity is turned on.

Just plug it in. Before using the hot fast handle, it is necessary to determine whether the part of the handle that is hot quickly used is kept dry. Once the power is turned on, the hand and the hot fast will inevitably have a contact process, once there is water on the handle, and there is poor contact or leakage, then it will definitely cause the risk of electric shock.

Therefore, before using it, pick it up and take a good look at it quickly, and it is best to wipe the handle area that is hot quickly with a clean paper to avoid electric shock.

Heating fast is a very convenient tool for boiling water appliances, its working principle is to simply convert electrical energy into heat, so that the temperature of the water increases, and the principle of the electric stove is the same, this is often seen in student dormitories or renters' rooms, so how to use it correctly when it heats up quickly?

1. Before use, it is necessary to check that the heat is dry quickly, and at least the hand-held part must be dry, so that people are not easy to be in danger when they are in contact.

2. If it heats up quickly, it can be directly put in the bucket to heat the water, so the water in the bucket should be at least submerged in the hot part of the heat, so as not to affect the service life of the fast heat, and also to prevent the barrel from accidentally burning and the problem of safety travel.

3. After the water is hot, don't rush to take it out of the bucket as soon as it is hot, it is recommended that it is best to take it out until it is hot and not so hot, so that it is not too hot, and it is easy to burn the body when it is taken out, it is recommended to wait for 5 minutes after unplugging.

4. After taking it out, wipe the hot water dry, then dry it, put it away or put it away, so that it is not easy to rust and shorten the life of the hot and fast use.

Regarding the knowledge of how to use it correctly when it heats up quickly, I have made a confident answer to share this above. After all, it is relatively dangerous, and if there is a condition, it is best to use a water heater or other safe way to boil hot water.

1. The two ends of the heating wire are connected to the power cord respectively. After the power is on, the current swims through the vertical flow of the beam mill in the heating wire, and the heating wire heats up. If you immerse yourself in a liquid that "heats up fast", the heat is quickly dissipated through the liquid, so that the liquid is heated quickly and the heating wire is not burned out.

2. If you let the "hot fast" dry burn in the air, the heat is not easy to dissipate, the metal outer tube will be quickly scorched, or even burned red, and the heating wire in the tube will burn off. Therefore, when using, you should first put the "hot fast" into the liquid, and the liquid should be at least flooded with a large unheated spiral ring (the handle and wire should not be immersed in the liquid), and then turn on the power supply. After heating, you should also disconnect the power supply first, and after a while, after the temperature of the "hot fast" is reduced, then take it out of the liquid and dry it for collection.

3. The power is generally about 1000-1500W, and it takes 5-6 minutes to boil a bottle of boiling water.

When using the hot fast, first fill 95% of the water in the bucket or basin, can not be filled, to avoid the use of water will overflow when the heat is fast, and then put the hot fast into the water after the water is loaded, pay attention to the use of the hot metal parts must be all soaked in the water, when the use of the hot fast must be someone next to the side.

Before using it quickly, be sure to check whether there is an alarm device, whether the wiring is aging, whether the use method is correct, and only after checking can you put it into the water to heat quickly, plug in the plug and boil the water.

When using hot and fast boiling water, do not boil for a long time after the water is boiled, continuing to boil will cause the water in the kettle to evaporate and become less, and when the water is boiled dry, it will lead to fire and other dangers.

Once it is hot and used quickly, it is found that there is an aging of the Hashino line, and the smell of burning plastic is smelled in the middle of the use, and the voltage is high and low during the ignition, please do not continue to use it, and immediately throw away the hot one.

1. First of all, check whether it is dry when it heats up quickly, especially the hand-held part must be kept dry. At the same time, it is necessary to check whether the heat is fast to rust and whether the line is aging. It heats up quickly and is connected to the handle, so if it is not dry, it is easy to have poor contact or leakage.

2. If it heats up quickly, it can be directly put in a bucket to heat the water, and the water in the container must not be overheated quickly, and it cannot be heated quickly, otherwise it will heat quickly and be easy to burn out. At least the water in the bucket should be submerged in the hot part of the barrel, so as not to affect the service life of the fast heating, and also to prevent the barrel from accidentally burning and causing safety problems.

3. After the water is boiled, unplug the electric plug when the water boils, and don't rush to take it out of the bucket as soon as it is hot. It is recommended to take it out until it is hot and not so hot, so that it is not too hot to get hot, and it is easy to burn the body when you take it out, so it is recommended to wait for 5 minutes after unplugging.

4. After taking it out quickly, wipe the water on it in time, then dry it, put it away or put it away, so that it is not easy to rust and shorten the life of the hot and fast use. If there is limescale or buildup on the surface, you can gently brush it off with a small brush, do not hit it with a hard object or scrape it with a knife.