How to dust the computer chassis, a good way to dust the computer chassis

If possible, you can open the chassis and blow it with a wind gun. If you don't have it, you have to remove all the hardware and slowly brush it clean with a brush.

Just take it apart and blow it. However, pay attention to anti-static. Or use a small bristle brush to brush it.

Blowing on the computer with an electric fan or a hair dryer is OK.

Computer cases accumulate a lot of dust, dirt, and exhaust gases during long-term use. This dust not only affects the performance of your computer, but it can also cause poor heat dissipation, which can lead to the collapse of your computer system. Therefore, regular cleaning of the chassis is one of the important tasks of daily computer maintenance.

Here's a great way to dust your computer case:

1.Air Spray Can: An air spray can is a convenient and quick case cleaning tool that sprays compressed air into your computer case to blow dust, dirt, and exhaust gases out. When using the air spray can, turn off the computer first and unplug the power cord to avoid danger.

2.Use a vacuum cleaner: A vacuum cleaner can help remove dust from inside your computer case. When using a vacuum cleaner, you should choose a vacuum cleaner with low suction power and use a soft vacuum nozzle to avoid damaging the internal components of the computer.

3.Clean with a brush: Using a fine-bristled brush to clean the inside of your computer case can remove some of the fine dirt and dust that are difficult to remove from an air spray can or vacuum cleaner. Care should be taken when cleaning to avoid damaging the internal components of the computer.

4.Wipe with a cloth: Use a cloth to wipe down the surface and inside of your computer case to remove grease, fingerprints, and dirt. The wiping cloth can be soaked in some detergent or alcohol, and it is best to choose a non-woven fabric or cotton cloth to wipe it.

5.Remove the radiator: The radiator is one of the most important heat dissipation components in the computer case, and special attention should be paid to cleaning. When using a vacuum cleaner, air spray can, or other tools to clean the radiator, you should pay attention to the cleaning direction and avoid repeated cleaning.

In short, the cleaning of the computer case needs to be done safely and gently to avoid unnecessary damage. The cleaning frequency is generally between six months and one year, and the cleaning interval should also be determined according to the time of computer use and the environment. Cleaning your case regularly not only improves your PC's performance, but also extends its life.

Generally speaking, I personally recommend that in the case of daily use of the computer, the computer should be cleaned and dusted at least once a year, preferably twice, too much is not necessary! (Unless the computer is in a really poor environment).

If you want to do a good job, you must first sharpen your tools, and before preparing for the dust removal work, we must prepare some tools! Generally speaking, ordinary players like us can dust and prepare leather tigers, erasers, brushes, alcohol, etc., and even hair dryers!

Then it is to directly remove the main engine, take it to an open place outside, open the side cover of the case, and first look at the dust accumulation of the air inlet and outlet of the case, including the air outlet of the lower power supply!

If you are a novice, it is best to see the various wiring places of the computer clearly, take pictures of the mobile phone and keep it, and then disassemble it....

When disassembling the graphics card, memory and processor, please be sure to pay attention to whether the graphics card, memory card, etc. are open and changeable! When picking up the processor, be careful not to get dust into the pins of the motherboard (Intel platform), and be careful not to get the pins crooked!

A good way to dust your computer case is as follows:

Use a compressed air tank or gas dust collector. It's a quick and easy way to clean small corners inside your computer's case, such as radiators, fans, internal wiring, and more. Remember to turn off the power before use to avoid damaging the circuit.

Clean with a soft brush. The Leeridge Soft Brush is a very gentle cleaning tool that cleans dirt and dirt from surfaces and easily reaches various hard-to-reach parts of the inside of the case. Before using it, you can take out some of the components of the computer, clean them one by one, and then install them back.

Clean the fan and radiator. Fans and heatsinks are the areas inside your computer case that are most prone to dust and dirt accumulation. It is important to clean these areas with a soft brush and compressed air canister, otherwise the computer may overheat, freeze or blue screen.

Pay attention to replace the filter regularly. Installing a filter at the exhaust vent of the circular chassis can effectively prevent dust from entering the case, but over time, the filter will clog and need to be replaced or cleaned regularly. Otherwise, dust will accumulate on the filter, which will affect the heat dissipation of the computer and even cause the computer to overheat.

1. Prepare tools, generally including screwdrivers, brushes, thermal grease, air blowing, etc. You need to pay attention to the disassembly money, be sure to wash your hands in advance, don't produce static electricity because your hands are too dry, otherwise there will be big problems;

2. Open the back cover, before removing the screws, be sure to figure out how many types of screws there are in the machine, remember the position of the screws for each screw, and then put the same type of screws together, and remember the position of each kind of screw;

3. Remove the keyboard, this step is very critical, you must be careful, otherwise it will damage the keyboard, generally there will be two locks on the top, as long as you open it gently, it is easy to remove the keyboard;

4. Remove the motherboard cover, this step is relatively simple, as long as you are careful, gently and slowly, there will be no problem;

5. Remove the fan, as long as the screws are properly unscrewed, and at the same time, slowly separate the fan from the connecting cable on the motherboard, which is also a simple process;

6. Removing the motherboard, a very important process, must be reasonably disassembled, and at the same time, it must not generate static electricity;

7. Dust removal, remove the motherboard, sweep the dust of the fan and the motherboard with a brush, and use a hair dryer if necessary. After clearing, hold the computer and assemble it according to the requirements of the specification.

1. Prepare tools, generally including screwdrivers, brushes, thermal grease, air blowing, etc. You need to pay attention to the disassembly money, be sure to wash your hands in advance, don't produce static electricity because your hands are too dry, otherwise there will be big problems;

2. Open the back cover, before removing the screws, be sure to figure out how many types of screws there are in the machine, remember the position of the screws for each screw, and then put the same type of screws together, and remember the position of each kind of screw;

3. Remove the keyboard, this step is very critical, you must be careful, otherwise it will damage the Qingdan keyboard, generally there are two locks hidden at the top, as long as you open it gently, it is easy to remove the keyboard;

4. Remove the motherboard cover, this step is relatively simple, as long as you are careful, gently and slowly, there will be no problem;

5. Remove the fan, as long as the screws are properly unscrewed, and at the same time, slowly separate the fan from the connecting cable on the motherboard, which is also a simple process;

6. Removing the motherboard, a very important process, must be reasonably disassembled, and at the same time, it must not generate static electricity;

7. Dust removal, remove the motherboard, sweep away the dust of the fan and the motherboard with a brush, and use a hair dryer when the stove is not needed. After clearing, hold the computer and assemble it according to the requirements of the specification.

1. Prepare tools, generally including screwdrivers, brushes, thermal grease, air blowing, etc. You need to pay attention to the disassembly money, be sure to wash your hands in advance, don't produce static electricity because your hands are too dry, otherwise there will be big problems;

2. Open the back cover, before removing the screws, be sure to figure out how many types of screws there are in the machine, remember the position of the screws for each screw, and then put the same type of screws together, and remember the location of each kind of screw;

3. Remove the keyboard, this step is very critical, you must be careful, otherwise it will damage the keyboard, generally there will be two locks on the top, as long as you open it gently, it is easy to remove the keyboard;

4. Remove the motherboard cover, this step is relatively simple, as long as you are careful, gently and slowly, there will be no problem;

5. Remove the fan, as long as the screws are properly unscrewed, and at the same time, slowly separate the fan from the connecting cable on the motherboard, which is also a simple process;

6. Removing the motherboard, a very important process, must be reasonably disassembled, and at the same time, it must not generate static electricity;

7. Dust removal, remove the main fiber board, sweep away the dust of the fan and the motherboard with a brush, and use a hair dryer if necessary. After clearing, hold the computer and assemble it according to the requirements of the specification.