How to use wood wax oil? How long can a good one last, and I don t want to brush it too much often

When the wood wax oil is painted, it must follow the direction of the wood grain, and the excess wood wax oil on the surface is wiped off after it is fully penetrated, and the general stay time is 1-3 minutes. The drying time between each pass is about 8 hours (good ventilation, temperature 25, 50% relative humidity), after drying, use 0 polishing pad or 400 sandpaper for light sanding to enhance the penetration of the second pass, increase adhesion, remove dust and apply a second pass. The final pass can be polished with a 00 polishing pad or a clean, soft cloth to achieve a better finish.

In general, it is no problem to store wood wax oil in a cool place and use it for 3-5 years.

It is recommended to brush the wood wax oil 3-4 times, at least 2 times.

Wood wax oil is a vegetable oil wax coating, commonly known as wood wax oil in China, which is a natural wood coating similar to paint but different from paint. Because the oil can penetrate into the wood, it deeply moisturizes and maintains the wood. Wax binds tightly to wood fibers to enhance surface hardness, water and stain repellency, providing the best beautification and protection.

Good quality wood wax oil is composed of natural vegetable oil, wax and other raw materials, the smell is very low, can be widely used in indoor wood decoration, furniture, flooring, outdoor wood products, ancient buildings, etc., the effect is remarkable. Its rich filial piety mu contains vegetable oil, which can penetrate deeply into the surface of the wood, and perfectly combine with the wood fiber, so that the wood presents a unique moisturizing feeling.

Stir fully before use, no need to dilute, no primer, directly brush (or rub) one to two can be naturally dried for 12 hours, that is, the mu can be wiped off with a towel or cloth to wipe off the excess wood wax oil on the surface, after a little drying, you can wipe and polish with a clean towel or cloth, you can get satisfactory results.

Because the molecules of wood wax oil are relatively large, it is easy to be deposited in the pores of the wood, and long-term use will make the grain of the wood unclear, thus affecting the appearance.

Wood wax oil is a type of oil extracted from plants, which is commonly used to maintain and lubricate wood products, such as furniture, wood floors, etc. Although wood wax oil has the advantages of natural and environmental protection, it is not recommended for long-term use, the surface tension of wood wax oil is relatively large, and it is easy to form a thin film, and long-term use will hinder the air permeability of wood, making the wood dry and fragile.

The use of wood wax oil will form a protective film on the surface of the wood, preventing the natural contact between the wood and the environment, thus affecting the natural aging and precipitation of the wood. Therefore, it is recommended that when using wood wax oil, it should only be used to treat the surface of the wood, not for a long time, and wipe it clean in time after use. If you need long-term maintenance of wood products, you can choose other materials that are more suitable for treatment.

Precautions for using wood wax oil

1. Choose the right wood wax oil: choose the right wood wax oil according to the type and needs of wood. Different types of wood require different wood wax oils, such as softer wood wax oil for harder wood and harder wood wax oil for softer wood.

2. Check whether the wood is suitable for using wood wax oil: some wood is not suitable for maintenance and protection with wood wax oil, such as wood that has been painted or painted, or wood that is polluted or damp.

3. Preparation: Before using wood wax oil, it is necessary to clean the surface of the wood, remove dust and impurities, and ensure that the surface of the wood is dry and flat.

4. Painting method: Before applying wood wax oil, you need to stir evenly, and then use a brush to evenly paint on the surface of the wood, do not apply too thick. If you want better results, you can wait a while after the first application before applying a second application.

5. Pay attention to safety: When using wood wax oil, you should wear gloves and masks to avoid direct contact with paint and inhalation of harmful gases. After use, the brushes and tools should be cleaned in time to avoid the wood wax oil solidifying and clogging the brushes and tools.

Wood wax oil. It is refined with a variety of natural vegetable oils and vegetable waxes as the base material. Penetrate deeply into the surface of the wood, enhance the texture and maintain the breathability of the wood; It can effectively prevent the wood from being deformed, cracked and warped by moisture, does not peel off and blisters after painting, and has excellent waterproof, anti-fouling and chemical resistance; It is harmless to the human body, has excellent environmental performance, and is widely used in indoor wood accessories, log furniture, children's wooden toys, wooden floors and other high-grade wood products.

Pure natural raw materials, without any toxicity, there are children at home do not have to worry about decoration pollution, very natural and refreshing feeling, and painted ordinary oily paint is different, surface treatment.

The surface of the wood is polished with fine sandpaper, smooth and clean, and if there is old paint, it must be removed; Wood moisture content 20%.

Construction method: before use, fully stir the liquid, no dilution, no priming, directly brush (or wipe) one to two can be naturally dried for 12 hours, you can use a towel or cloth to wipe off the excess wood wax oil on the surface, after a little drying, you can use a clean towel or cloth to wipe and polish, you can get satisfactory results. Construction conditions:

It can be applied in all seasons, and the use of theoretical coating rate below zero does not affect the use of the theoretical coating rate: 16-20 per liter can be brushed or wiped (the actual amount is determined by the specific construction method and the surface condition of the substrate) Drying time: 4 can be recoated after 6 hours (wood wax oil is a penetration method, which is very different from traditional paint, and there is no real drying) A Scope of use:

a) Logs, finger joints.

b) Plywood.

and other decorative boards with a layer of veneer on the surface.

c) Do not use decorative panels for surface stickers.

2. Painting method:

a) Brushing: Ordinary brushes that do not shed hair.

b) Polishing: small towels and cotton cloths that should not be shed.

3. Painting Procedure:

a) The surface of the workpiece is polished until it is satisfied.

b) Evenly paint 1-2 times with a brush (the inside of the wardrobe can be brushed once, only the important parts such as the desktop need to be brushed on both sides).

c) Dry naturally for no less than 1 hour (no need to wait for drying), it is better to dry for a longer time to facilitate penetration.

d) Use a clean towel to wipe off any excess wax oil on the surface.

e) After a little drying, polish with another clean, dry towel until you are satisfied.

4. Auxiliary Notes:

a) If you want to get a smooth effect or fill in wood with large eyes, such as ash, you can scrape the transparent putty before applying wood wax oil.

However, be sure to wait for the putty to dry fully and polish it clean, and do not leave a thick layer of putty, so as not to affect the penetration of wood wax oil.

b) Wood wax oil is the principle of penetration, and there is no dry world and paint film like polyester paint.

c) Painting can be done 1-2 times, and there is no need to worry about leaving brush marks.

Wood wax oil is a kind of environmentally friendly wood coating used in various wood products, bamboo products, rattan products, simple construction, environmental protection, natural texture, delicate texture is its characteristics, but also the reason why many people choose wood wax oil, very suitable for DIY, no construction experience personnel can also operate the construction, construction is generally 2-3 times. Hunger.

Wood wax oil construction steps:

1. Polishing the substrate to make its surface clean and dust-free.

2. Stir the wood wax oil fully to avoid the separation of oil and wax caused by long-term stationation.

3. You can use brushes, cotton cloths, spray guns and other tools to apply it, brush it thinly, do not build too thick, and avoid slow drying.

Fifth, polishing and grinding, with about 1000 mesh of fine sandpaper or polishing surface of the wood wax oil surface for gentle grinding, can play a role in the beam to add brightness and feel, outdoor requirements for it is not high, can also not operate this step.

The Immex wax oil I used before was usually wiped with a cotton cloth.

It is recommended that you use it.

bai 3-4 times, at least 2 times.

DU Steps: zha

Step 1: Substrate Processing.

Completely remove the sanded DAO dust back to clean.

The second step answers: thin rub the first pass.

Open the wood wax oil and stir well (you can add an appropriate amount of Cheresib deodorant thinner), dip an appropriate amount of wood wax oil with a cotton cloth, wipe it along the direction of the wood grain, make sure that all the surface layers have been wiped, and use a clean cotton cloth to clean the excess oil on the surface to ensure that there is no excess oil on the surface.

Step 3: Polishing.

After the first pass is completely dry, lightly polish the surface layer that has been rubbed with wood wax oil, and completely remove the sanding dust.

Step 4: Rub it a second time.

Please wipe it again according to the process requirements, generally wipe it 2 or 3 times, and please follow the third step for slight polishing between the thin wipe and the thin rub.

Step 5: Polishing.

After all the construction steps are completed, use more than 1000 sandpaper or special polishing cotton for Cheresi to lightly carry out the surface layer.

Polishing, and clean the surface sanding dust to enhance the feel.

The third and fourth times are the same as above.

Note: Cherexi furniture series wood wax oil, due to different climates and environments, the viscosity will be different, can be used with Cherexi thinner.

Coating method 1, brushing: ordinary copy does not shed the hair bai brush; 2. Polishing du: small hair towels and cotton cloths that should not be shed. Painting program 1, work dao

The surface of the piece is polished to a satisfactory level; 2. Evenly paint 1-2 times with a brush (you can brush the inside of the wardrobe, only the important parts such as the desktop need to be painted on both sides); 3. Dry naturally for no less than 1 hour (no need to wait for drying), and it is better to dry for a longer time to facilitate penetration; 4. Use a clean towel to wipe off the excess wood wax oil on the surface; 5. After a little drying, polish with another clean, dry towel until you are satisfied. Auxiliary instructions 1, if you want to get a smooth effect or fill the wood with large wood eyes, such as ash, you can scrape the transparent putty before brushing the wood wax oil, but you must wait for the putty to be fully dry and polished clean, do not leave a thick layer of putty, so as not to affect the penetration of wood wax oil; 2. Furniture wood wax oil is the principle of penetration, and there is no drying and paint film like polyester paint; 3. Paint 1-2 times, and there is no need to worry about leaving brush marks.