What s the deal with the mop spinning barrel not spinning?

Updated on home 2024-03-06
7 answers
  1. Anonymous users2024-02-06

    The mop bucket can be rotated in two ways:

    One is to rotate by pedaling, and the other is to rely on the spiral groove inside the mop rod to turn the linear motion of pressing the mop rod up and down into a rotary motion. If you can rotate with your foot, it means that there is no problem with the mop barrel, that is, the mop bar is broken, which cannot be repaired, and it is generally this problem, and you can only replace it with a new mop bar.

    Precautions: 1. Check whether the new mop head is a mop cotton head for automatic mopping.

    2. Confirm whether the head in the bucket is suitable, so that you can confirm that the problem is **, it is best to buy accessories of the same brand in the place where you originally bought.

    Repair method. 1. Please prepare 1 bottle of lubricating oil, the kind used for bicycles. Turn the mop upside down, then drip oil at the entrance of the mop mop rotation telescopic, and then drop a circle on the outside of the rod to let the lube slowly slide inside, and then rotate the mop lever several times.

    2. Lay the mop bar flat and rotate the mop bar several times again to let the internal parts be evenly oiled. Then place the upper part of the mop stick and unscrew it. Drip some lube from the unscrewed inlet. Turning the mop many times to make the parts evenly oiled, and the feeling becomes flexible, it is a successful refueling.

  2. Anonymous users2024-02-05

    Just loosen the plastic fasteners in the middle of the mop lever a bit. Once tightened, it cannot be rotated. Tighten when mopping. Release while rotating.

  3. Anonymous users2024-02-04

    The mop bucket is not spun dry, but what should I do if it does not turn below.

  4. Anonymous users2024-02-03

    The repair and disassembly diagram of the rotating mop barrel without turning is as follows:

    If the mop barrel does not rotate, there should be a problem with the rotating shaft inside. You can open the barrel to see if the steel balls in the empty groove are normal, and if the steel balls are worn out, they should be replaced with a new one.

    It is also possible that the pedal spring of the mop barrel is not elastic enough, resulting in excessive friction and locking, you can remove the damaged spring and install the new spring on the bayonet of the ruler.

    The solution to spin the mop itself does not turn:

    Generally, the rotating mop is composed of two parts, there is an interface in the middle, if the mop itself does not rotate is a problem with the interface, use a hacksaw to split the middle into two sections, check whether there is a problem at the interface, and then check whether the nut on the disc is working normally, if there is damage, you can change a new nut, and then install the mop head.

    There is also a possibility that the mop ruler will have friction with both sides after using it for a period of time, resulting in the inability to rotate, the solution is to remove the ruler and flatten the teeth at the upper and rear ends of the ruler with a knife to increase the space on both sides without friction.

    The method of changing the head of the mop is as follows:

    First of all, put the rotating mop pendulum rock dust on the flat ground, firmly step on the board surface with your feet, and turn as close to the metal part as possible. Then hold the handle of the mop with your left hand, rotate the base part counterclockwise, and when you hear a "click", it means that the handle of the mop and the head are separated, and then you can remove the old mop head.

    Then clean the mop handle with water and steel wool balls, prepare the new mop head to lay flat on the ground, and rotate the mop handle clockwise towards the center of the head, which also produces a "click" sound, which means that the installation is completed. Finally, lift the mop and observe it carefully to see if the mop head and the mop handle are completely consistent, and if you can, you can use it normally.

  5. Anonymous users2024-02-02

    Rotate the mop to spin the dry barrel without turning the maintenance method: the ruler needs to be repaired due to the untimely return, and the mop rod needs to be replaced for the built-in spring problem of the hand pressure bar.

    1. It may be caused by untimely return. The reason for this phenomenon may be that the ruler of the rotating mop bucket has been used for a long time and friction has occurred on both sides.

    I can use a screwdriver to remove the foot pedal of the rotating mop bucket, and then use the hexagonal inner buckle to remove the red big gear, and then remove the ruler, use a knife to cut the six or seven teeth at the back end of the ruler slightly, and then reinstall it, or directly replace it with a new ruler.

    2. There is also a double-drive rotating mop barrel, which generally drives the rotation of the mop barrel by pressing the mop rod by hand. If the rotating mop barrel does not rotate, it may be that there is a problem with the built-in spring of the hand-pressed pole. If it is caused by this reason, it is usually impossible to repair and there is an option to replace a mop pole.

    Maintenance of the swivel mop

    1. After use, it must be scrubbed and wrung out, and placed in a ventilated place to avoid odor and odor.

    2. When the mop has a peculiar smell, you can use diluted bleach to clean the mop.

    3. When the hair on the mop sticks, you can use a brush to help remove it, or wait for it to dry before sticking it off with tape.

    4. In order to keep the home clean and hygienic, it is recommended to replace the mop head every two to three months.

    5. Use with detergent, the amount should not be too much, otherwise it is easy to remain and affect the service life of the mop.

  6. Anonymous users2024-02-01

    The mop bucket doesn't turn, and the mop can't be dried, what should I do, let's take a look at how to deal with it.

    The mop barrel doesn't turn, you can't shake the mop dry, and there is no repair shop to repair it, so you have to figure it out by yourself.

    Remove the white accessory of the rotating bucket first.

    The white shaft on the top of the rotating barrel cannot be taken out, and the rotating shaft below should be rusty and cannot be taken out.

    With both hands, you can pinch both sides of the filter with both hands, and slowly rotate it upwards and lift the filter upwards with equal force.

    I saw that the shaft below was rusty, the white fitting was inserted in the barrel, and the iron shaft was rotating.

    The surface of the shaft was rusty and tangled in silk hair. The white fittings need to be removed.

    Here are the steps to remove rust from the rotating shaft. You can soak it with white vinegar first, and then wipe off the rust.

    Finally, it is processed and the installation is complete. When disassembling parts, pay attention to the control of strength.

  7. Anonymous users2024-01-31

    If you choose a rotating mop at home, this kind of mop is still more convenient to use. But what should I do if I have a problem that I can't rotate?

    1. What should I do if the rotating mop can't be rotated.

    The use of a rotary mop is mainly to generate centrifugal force through rotation, which can spin the mop dry. However, if you can't rotate it, check the center of the mop barrel first, and remove one of the body shafts first, it is possible that the rotation shaft has rusted and caused it to get stuck. You can soak the white vinegar solution for a while to remove the rusty area, and then try again.

    Or if something is wrapped around the bearing, such as hair or some wires, etc., clean it up first, and then reinstall it again, which can basically solve the problem of not being able to rotate.

    2. Is the rotating mop easy to use?

    1. I also use a rotating mop in my house, and its convenience is relatively good. And it is relatively simple to use, equipped with a mop bucket. You can fill it with water first, and then install the mop rod on the mop, as long as the mop is placed flat on the ground, and then the mop rod is stuck vertically on the mop.

    2. When you hear a click, you can install it successfully, and then combine the upper and lower rods of the mop with the card rod and rotate it hard. The mop is then placed vertically in the rotating bucket and then in the spun dry bucket. Throw it off in a certain direction, and after starting, you can accelerate, about 5 or 6 strokes.

    Wait until it is completely stationary, then adjust the mop lever to the appropriate height.

    3. If the switch is locked, it can be used for mopping. It can be used not only to mop tile floors, but also to mop wooden floors. However, when mopping the wooden floor, the mop should be dried so that no water stains remain on the floor.

    4. After use, clean up the mop and expose it to the sun so that it can be used again next time. Pay attention to the cleaning work, otherwise it will cause secondary pollution.

    I conclude: The above is what the rotator mop is not able to rotate, what is the reason, and how to solve it. If you buy a rotating mop at home, it is not expensive, and it is very convenient to clean and very practical.

Related questions
11 answers2024-03-06

This needs to set the IP address of the network card, you ask what the IP gateway of your neighbor is and then remember to set the DNS If the computer does not have the network card after repair, you have to right-click on the online neighbor, properties, and then see if there is a local connection, if there is no local connection, it means that your new motherboard does not have a network card.

18 answers2024-03-06

Reason: It is possible that the remote control battery is dead; It is also possible that the air conditioner is set to automatic; It could be that the remote control button is broken. Workaround: >>>More

11 answers2024-03-06

The length of sleep is not indicative of sleep quality.

I also sometimes don't sleep well, I think it's because I have too many things in my heart to let go, so even when I sleep, I am thinking about it, the easiest way is to solve my worries, and if I can't solve it, put it aside for the time being, there will always be a solution, after all, there are always more ways than problems, so that you can relax, let your heart really relax, so that you can naturally sleep well, and finally drink a glass of hot milk before going to bed, everything is OK, of course, it may not be effective, But the psychological effect is the most important. >>>More

17 answers2024-03-06

First of all, light is also a kind of matter, and even time can bend or change speed or change direction, of course, light is a collection of energy block photons, photons move at the speed of light to have mass, in the face of the extreme density of black holes, the strong gravitational force can absorb it. >>>More

27 answers2024-03-06

There are several reasons, such as qi stagnation and blood stasis caused by congestion, pain if it is not passed, cold condensation of blood veins caused by body cold, pain caused by weakness of qi and blood, and dysmenorrhea due to poor qi caused by emotional factors! More often than not, several situations appear at the same time!