What is the most appropriate gap for tile joints?

There are many specifications for tile seams. Conventionally, in addition to retro bricks, a large gap of 5mm to 10mm needs to be reserved. Other bricks are generally 3 to 10mm is better, the front is 1 to 2mm is better, and the specific is determined according to the design style of the house and some factors such as his layout.

The type of tile is generally a flow joint.

1.There are many factors that go into the size of the tile reservation location. There are wall tiles, floor tiles or areas divided into kitchens and bathrooms.

Generally speaking, the reserved space for the gap between wall tiles should be about, not less than 1mm; The gap between the wall tiles of the kitchen and bathroom should be about 1mm. In general, the size of the slit can be used as a reference for a bag or air nail. If it is a special effect tile, you can also widen the gap, such as 5mm.

2. Floor tiles can be divided into living room floor tiles, kitchen and floor tiles, such as vitrified tiles in the living room, which are laid about; The gap between the kitchen and the floor tiles is generally not too large, about about the left. It is advisable not to leave gaps too much. If it is too large, it is easy to build up dirt, difficult to clean, and affect the appearance.

3.How big a seam do you need to leave for tile seams? In fact, look at it and there is no uniform gap rule.

It depends on the type of brick. For example, the tiles should be smaller and the bricks should be larger. If the living room tiles leave a gap of about 2mm, the wall tiles should leave a gap of about 2mm, and the floor tiles should leave a gap of 2-3mm.

If the bricks of special specifications need to be cut 3-5mm. However, this data can only be used as a reference. In particular, you should listen to the advice of the decorator so that it does not cause trouble later.

1. Leave a seam of 1 mm for wall tiles.

2. The floor tiles should be seamed by 2 mm-3 mm.

3. For seamless bricks, the joints should not be less than 1 mm.

4. Special specifications of bricks (such as small size bricks, balcony long bricks, etc.), leaving a gap of 3 mm-5 mm.

In addition to meeting the factors of thermal expansion and contraction of the tile itself, it is also necessary to combine the decorative effect of tile paving. Generally, the size of the seamless wall tile in the kitchen and bathroom is about 1, and it cannot be less than 1mm. And when the floor tiles are paved, it is generally around the left.

The specifications of the ceramic tile seam should be determined according to different types of tiles and the actual decoration situation. Generally speaking, retro bricks need to leave a large gap, generally 5mm-10mm; Other brick types are generally 3mm-10mm, but the specific can be determined according to factors such as house design style and layout.

If you look at the type of tile alone, the general beauty joint is used for seamless tiles and marble tiles, for wall tiles, for small size tiles, for medium size tiles, for large size tiles and outdoor tiles.

Please leave a 2 mm seam The commonly used ceramic tile specifications in the restaurant are *500 imitation bricks, 150*900 imitation wood grain bricks. 800*800 floor tiles and 600*1200 floor tiles leave 2mm joints without design or wavy lines. Design the shape and corrugation of the floor tiles, the gaps of the floor tiles can be 3 mm wide and the beautiful joint effect is beautiful.

At present, there are three kinds of white cement putty powder and beauty sealant on the market, among which white cement and putty powder have some shortcomings in performance and poor waterproof effect. Therefore, it is advisable to choose a beauty sealant with good performance, which can completely solve the problem of dirty blackening of tile joints. Time-sensitive joint filling and beautiful joint manipulation on the tiles can only be done within 24 hours after the tile is placed, so the tiles are not strong enough after the packaging is completed.

If you make beautiful joints yourself, it is easy to have problems such as tile displacement.

Leave a gap of 3 mm, the smaller the size of the tile tile, the better the joint effect, the tailor can highlight the three-dimensional effect of the tile. 150*900 specifications of imitation wood grain tiles, imitation wood grain bricks are relatively brittle. Especially when applying tiles when the edges are in contact, it is better to leave a seam of 2-3 mm, and the effect of making particles is very good.

It is recommended that wall tiles of the same size, if they are not imitation bricks, only need to leave 2 mm joints. For 400*800 wall tiles, if the tiles are on the wall, it is recommended to leave a 3 mm joint. The sewing effect of 2mm sewing is not as good as that of 3mm sewing.

The width of the gap of 400*800 chamfered wall tiles is 5 mm, the brush effect is 45 degrees, and the overall brush effect is more obvious.

The 300*300 imitation floor tile packaging area is commonly used in kitchens, bathrooms, balconies, etc., and it is best to leave 3 mm joints when tiling. Please do not leave a gap of less than 2 mm. That is, making beautiful seams is ineffective.

500*500 specifications and 600*600 specifications of horned bricks, imitation bricks with horned flowers, must leave a gap of 5 mm. 800*800 specifications and 900*900 specifications, large floor tiles can leave 2 mm joints, large floor tiles do not need to leave 3-5 mm gaps.

It is more appropriate to leave about three millimeters for the width of the ceramic tile joint, which can be better for the seam, and it is more beautiful, and does not affect the overall effect.

To do tile seams, it is appropriate to reserve a width of two millimeters, so that you can easily stuff the seam agent into it without overflowing.

1.The left seam of the tile has mm, mm, mm, mm, Generally speaking, except for retro bricks, which need to leave a large gap (5mm-10mm), other types of bricks are generally better than 3-10mm.

The wall surface should be 1-2mm, which can be comprehensively decided according to the design style and layout of the house. For general household use, it is recommended to use a gap of 2 3mm, which will not waste materials and is simple and beautiful.

2.Tile and brick joint side wall cleaning: Use a paper cutter to clean a groove in the tile joint, the groove depth is best in mm, this is all meticulous and patient work, bend over and squat on the ground to clean up a little bit.

If you don't do physical work often, you may die of exhaustion after squatting for a while. It's really hard work. If you want to do it yourself, be mentally prepared in advance.

The most laborious and convenient way to clean the dust in the tank is to use a vacuum cleaner. Many people use brushes, it's not that they can't use it, it's just that it's too laborious, and they have to be cleaned slowly one by one. Vacuum cleaners are much more convenient.

3.After sewing the seam agent, the gap should be flattened with caulking steel balls. By the way, many people worry about not doing it well the first time.

Here's a suggestion for you. If you do it yourself, if you are worried about the effect, you can start the experiment in some hidden places, such as the sofa or under the bed. If the effect is not ideal, it can be adjusted in time, and the cosmetic impact is not great.

Construction quality standards: the brick surface is required to be smooth without edges and corners, no bubbles, no pits, no spills, and the ground is clean as new before exiting; The distance of the seam is not fixed, so whether the seam is 2mm or 3mm depends on the actual size of the tile and the way it is laid.

4.There are places where larger aesthetic seams are needed to add to the overall effect of the décor. Generally, the beauty seam of home decoration tiles is 2mm to 3mm.

Tile joints are also a technical job, so mastering the steps of tile joints requires professional construction to achieve the best tile laying and caulking. If the customer is afraid that the spillage on the brick surface will not be wiped clean after construction, you can use masking tape to stick to the edge of the brick joint, and then use a glue gun to beat the material. After scraping flat with a spatula, after the material is dry, the masking tape can be opened after repair.

Generally, you need to leave a distance of about 5 10 mm is more appropriate, you should determine the distance left according to your own home decoration style, if your home is generally decorated with a more integrated neat and clean simplicity, you can choose to use a distance of 5 mm to sew the seam, if the style of installation is more European-style generous feeling, you can choose to use 10 mm of sewing.

It is more appropriate to leave about 1 2 mm, so that the gap can be better maintained. It is also not prone to dirt.

About two millimeters will be more suitable. In the later stage, it can avoid thermal expansion and cold contraction, and it can also be convenient to do beautiful sewing in the future, which can make the home cleaner and easier to clean in the later stage.

The specifications of the seam of the tile seam are and so on. Generally speaking, in addition to the retro bricks, which need to leave a large gap (5mm-10mm), other bricks are generally better than 3-10mm. The wall surface is 1-2mm, which can be comprehensively decided according to factors such as the design style and layout of the house.

In terms of the types of tiles alone, they are used for seamless tiles and marble tiles, for wall tiles, for small tiles, for medium-sized tiles, for large-size tiles and outdoor tiles.

For general household use, it is recommended to leave a gap of 2 3mm, so that it does not waste materials, and is simple and beautiful.

2mm-3mm slit.

1. The most common wall tiles in the living room are 300 * 600 specifications, or 400 * 800 specifications, these two specifications of wall tiles, it is recommended to leave 2mm-3mm gaps when paving, if you want to have a very prominent effect, then, 3mm gaps are undoubtedly the best.

2. The commonly used specifications of floor tiles in the living room are: 600*1200 specifications, 800*800 specifications, 600*600 specifications of antique bricks, as well as 500*500 specifications of antique bricks, and 150*900 imitation wood grain bricks.

Suggestion; 800*800 specifications of floor tiles, and 600*1200 specifications of floor tiles, in the absence of design modeling and waveguides, can leave a seam of 2mm. If the floor tile is designed with modeling and waveguide, the gap between the floor tiles should be left 3mm wide, so that the beautiful seam effect is beautiful.

The carefully selected tiles are completely responsible for the appearance of the home. Tile must be left seamless. Seamless bricks also need to be seamed, but the gaps left by seamless bricks are slightly smaller.

Ordinary ceramic tiles: ordinary ceramic tiles are the most commonly used polished and glazed tiles in home decoration. According to the consistency of this type of tile pattern, it is generally recommended to leave a gap of 2-3mm to show the beautiful seam effect.

Large-size tiles: Large-size tiles are generally defined by the ceramic tile industry with a side length of more than 800mm, and such tiles are generally laid in the living room, dining room and other areas, and it is generally recommended to leave a gap of 3-5mm.

TV background wall: Due to the decorative nature of the TV background wall, in order to reflect the three-dimensional and atmospheric feeling, the tiles tend to leave a wider gap than usual, and it is generally recommended to leave a gap of 4-8mm.

Tile beauty seam retention problem: 1. If it is an ordinary tile, leave a seam of 2-3mm, and the effect is the best. 2. If it is an antique brick with a seam of 3-5mm, the best effect will come out of this, and Buyjie real porcelain glue hopes to help you.

Then it depends on what kind of tile is pasted, if the ground is polished brick, it can be left with a gap, if it is an antique brick, it will be 3mm 5mm, or if it is a floor tile, you can leave a 2mm gap, and the wall tile is generally yes.

It is best to leave the gap above, and the construction effect is the best

Generally on the line, for seamless bricks and marble tiles.

2 mm, don't be too big.

The function of caulking with caulking agent is to beautify the paving effect of the entire tile, so that each brick is more coordinated with the brick, and a good caulking agent can also play a waterproof role, so that the water on the tile will not penetrate into the ground or wall, ordinary caulk can not be blistered, and it is easy to fall off after blistering.

The beauty joint agent is directly added to the tile gap after the tile bonding, to solve the tile gap is not beautiful and dirty black problem of decoration materials, is the upgrade of the grout, decoration, practicality is better than the color caulk, its raw materials are high-tech new polymers and high-grade pigments, the form is ceramic texture, semi-liquid liquid, rich in color, natural and delicate, waterproof and mildew-proof.

The process of making beautiful seams for tiles is:

1. Make pre-construction preparations, deal with tile joints, and use a small shovel to shovel out a groove within 2 mm deep for the tile joints, which is not only convenient for playing the beauty joint, but also can avoid excessive wear and tear in the future.

2. Use a small brush to sweep away the dirty things that are shoveled;

3. After the preparation is done, you can open the sewing agent, first use a small awl to tie the mouth of the sewing agent, and then install it on the glue gun, the method of loading the glue gun is relatively simple, along the brick joint;

4. Hit a brick joint and immediately use a scraper to scrape the tile gap and smooth the joint;

5. The new sewing agent is a quick-drying type, so it should be cleaned up with a wet sponge after more than 10 centimeters, otherwise it will be difficult to clean;

6. The surface is completely cured within two hours after the construction is completed, and the construction surface can be used normally within 24 hours.

Question 120 60 How much time do you want to stay on the floor tiles?

It is more appropriate to leave 10 mm, because such a width can be made with a wider seam, which will look better.

Generally, it is okay to stay, if it is too wide, it will highlight the presence of beauty sewing agent too much.

Generally, it is more appropriate to leave 4 5 mm, because 4 5 mm will not affect the overall appearance, and it will not affect the thermal expansion and contraction of the tile.