You know how to set up the broadband control of the Tengda 837R wireless router

The first line of the following service is no problem, IP address 2-254, the direction is the best in both directions, it is okay to limit ** alone, the bandwidth range can be set as much as you want, at least 10, start on the point, add to the list.

Hello, first connect the router on the wiring (the network cable pulled in by the landlord is connected to the router WAN port, and the router LAN port is connected to the root network cable to the computer), enter the "pop-up box password" in the browser address bar and enter the "admin" to enter the router settings interface, select the Internet access mode to automatically obtain, set the wireless password, and click "OK".

Tips: Pay attention to how much the local connection IP address obtained by directly connecting the home network cable to the computer, the LAN port IP of W837R is, and the IP address obtained from the landlord router cannot be in the same network segment as the LAN port IP of W837R (that is, it cannot be the same. If you are in the same network segment, you can enter the W837R setting interface in the upper right corner of the "Advanced Settings" -- Advanced Settings -- LAN port settings -- modify the LAN port IP address (if you click "OK" instead, the router will automatically restart, and then enter the interface with the newly modified LAN port IP.)

The setup method of Tengda wireless router** is as follows.

The landlord has a router...Is it? I can pull a network cable There should be.

If there are two routers for wired bridging, set up the route with the computer...

Broadband modem (ethernet port) - network cable - (wan port) routing (lan port) - network cable - computer.

1.Open IE and log in to the router settings interface (the default or 2Enter your account and password to access the Internet.

3.Set up PPPOE to access the Internet

4.Select Auto-connect.

5.Enable DHCP on the router

Wireless router: Configure the channel of the SSID to auto or 6 by defaultSave the settings and restart.

Don't have an instruction manual?

And what exactly do you want to set up?

1.You can connect the broadband cable to the routing WAN port, and use one network cable, one end to the computer, and one end to the routing 1, 2, 3 interface.

2.Open your computer browser and enter the router settings interface in the ** bar.

3.If you don't connect to the router, the broadband line is directly connected to the computer and you need broadband dial-up to access the Internet, the router selects ADSL dial-up for Internet access, if you don't need to dial up, you can select Auto Get for Internet access, click "Wireless Encryption" to set the 8-digit password and click OK.

4.Click "For other Internet access type settings, please click Advanced Settings" - Running Status - WAN Port Status to show that you can access the Internet when you are connected.

1. The bus of the broadband network is connected to the WAN port of the router, and the LAN port of the router is connected to the computer.

2. After starting the device, open the browser and enter it in the address bar to enter the wireless router settings interface. (If you can't get in, please look at the nameplate at the bottom of the router or the router instruction manual, the default settings of different models of routers are different.) ）

3. An account and password to log in to the router appear in the settings interface, enter the default account and password admin, or refer to the manual;

4. After successful login, select the interface of the setup wizard, which will automatically pop up by default;

5. After selecting the setup wizard, a window will pop up to explain that you can set the basic parameters of the router through the wizard, and click Next directly;

6. Set up step by step according to the setup wizard, select the Internet mode, usually ADSL users choose the first PPPoE, if you use other network service providers, select the following two according to the actual situation, if you don't know how to choose, directly select the first item to automatically select, convenient for novice operations, click next after selection;

7. Enter the account and password applied for from the network service provider, and go directly to the next step after the input is completed;

8. Set the wifi password, try to make the alphanumeric combination more complicated, and it is not easy to be rubbed off the network.

9. After entering correctly, it will prompt whether to restart the router, select Yes to confirm the restart of the router, and you can access the Internet normally after restarting the router.

Connect the cable out of the cat to the WAN port of the router and then connect a cable to the LAN port of the router to the notebook After powering on, enter it in the notebook browser or enter the router settings interface in the setup wizard Select PPPoe Next, enter the Internet account password given to you by Telecom Next, choose to turn on wireless and set the wireless password Save it on the line After Netcom, you can remove the laptop cable Laptop and iPad are wireless.

[Network cable connection].

1. (There is an adsl modem cat) Connect the ** line (the thinner line) to the cat's line port (a smaller one), and the cat separates a network cable to connect to the router's WAN port (blue), and then find a short network cable, one end to the computer, and one end to the router 1 2 3 4 any interface (yellow);

2. (No adsl modem modem) directly connect the network cable to the WAN port of the router, and then find a short network cable, one end to the computer, and the other end to the router 1 2 3 4 Any interface (yellow).

Log in to the router].

1. Open the IE browser, enter the default IP address of the router (and press Enter;

2. In the pop-up login window, enter the username: admin; Password: admin; Then click OK, if you have entered the username and password correctly, the browser will enter the main page of administrator mode;

Router Settings].

1. Choose the correct Internet access method to set up, there are three common Internet access methods: PPPOE, dynamic IP, and static IP (static IP is in the advanced settings);

2. ADSL dialing: Select "ADSL dialing" in the settings page, enter the broadband user name and password provided by the broadband operator (such as China Telecom, Unicom, etc.) in the "Broadband User Name" and "Broadband Password", and click "OK". Here we demonstrate the ADSL dial-up method used by the average home user.

3. Change the wireless password and wireless signal name.

Click "Wireless Settings" - "Wireless Security" to set the wireless password;

4. Click "Wireless Settings" - "Wireless Basic Settings" in the settings interface to modify the wireless signal name;

5. Click "Advanced Settings" - "Running Status", if the WAN port status shows "Connected", you can browse the web and surf the Internet.

How to configure a wireless router:

1.Connect the network cable to the WAN port of the router and connect your computer to any LAN port of the router with the network cable. When the LAN port flashes when the computer is turned on, it means that the computer has successfully established communication with the router.

2.Turn on the wifi of the computer, search for the default wifi name of the router (the nameplate on the back of the router is written), and connect to the wifi network. The first time you use the router, you generally don't need to enter the wifi password.

3.Open a computer browser and enter the gateway IP address of the nameplate on the back of the router (generally, enter the gateway configuration interface. (This interface will pop up automatically for new routes).

4.Set the Internet access mode (dial-up or static IP, etc.), set the wifi name and password, and also set broadband restrictions.

To configure a wireless network at home, you need to purchase the following equipment:

A wireless router with a suitable signal range.

2.A long enough network cable connects the router to the home cable or switch.

3.Make sure the device supports WiFi and the desktop is equipped with a wireless network card.

Here's how to set up your router:

1. Line connection:

a.Connect the network cable from the cat to the router (WAN port), and then connect the network cable connected to the computer to the router (any port numbered 1, 2, 3, 4).

b.Connect the broadband cable to the router (WAN port), and then connect the network cable connected to the computer to the router (any port numbered 1 2 3 4).

2. Log in to the router interface.

In the browser, type: Enter, enter in the pop-up page: admin and click "OK".

3. Set up the router to surf the Internet.

Before setting up the Internet access, choose the correct Internet access method: Generally, there are three types as follows:

ADSL dial-up: Usually to access the Internet (when not connected to the router) need to click on the broadband connection, dial-up is successful before you can access the Internet, you should choose the Internet mode, Internet access and Internet password correctly enter the broadband and password, you can.

Automatically obtain an IP address: If you usually surf the Internet (when you are not connected to the router), you only need to set the local connection of the computer to automatically obtain the IP address to access the Internet, you should choose this Internet access method.

Static IP: If you need to fill in a fixed IP address in the local connection to access the Internet (when you are not connected to the router), you should choose the Internet access method, log in to the interface of the router, click "Advanced Settings" - "WAN Port Settings" to select the static IP mode "Static IP Mode", and enter your fixed IP address, subnet mask, gateway, DNS domain name server and other parameters correctly.

4. After setting, click "Advanced Settings" - "System Status" to check whether the connection status of the WAN port shows that it is connected, and whether the corresponding connection mode is displayed correctly.

The corresponding connection mode for ADSL dial-up is: PPPoE

The connection mode corresponding to the static IP address is the static IP address

**The following is how to set it up

Routing is the use of routing, which can also be used as a wireless AP or a switch.