What should I do if the white edged filler used in the film gets into the phone?

White edge filler is not a corrosive liquid. It is the corner gap between the screensaver and the mobile phone screen that is not tightly glued, find a way to deal with it, and the liquid used to fill it is like the filling gap material used to build a house. Dry.

If you don't block the earpiece, it won't have any effect, and it won't hurt the phone, it's fine, it's nothing.

White edge filler is a kind of thing that can make the white edge disappear by applying it to the gap between the tempered film and the mobile phone screen: it is an oil product: if it is used on a mobile phone that is not waterproof or does not have a high waterproof level.

Recently, with the increasing number of mobile phones with curved screens, mobile phones are facing a new problem with tempered film, that is, the screen is curved and the film is flat, and there will be big white edges on both sides of the screen, which is particularly ugly.

It's not just ugly, because the presence of the gap between the screen and the tempered film is simply a certainty.

Most of the white edge fillers on the market are vegetable oil, and a certain amount of liquid is dipped in a needle or fine brush to fill the gap between the screen and the film, that is, in the white edge, and the white edge will disappear naturally after filling.

But there are two problems with this way of removing white edges:

When filling the white edge with liquid, if the phone is not tightly sealed and the liquid accidentally enters the inside of the phone through the gap, the consequences are unimaginable. There are a lot of such cases on the Internet:

2.Treating the symptoms is essentially adding filler to the gaps of the white edge, and if you squeeze the tempered film, you will find that the oil comes out of the gaps, and then the white edges are produced again.

Three days after Chubby's mobile phone was greased, the white edge reappeared, and he didn't care at all.

1. Open the white edge filler and open the seal with scissors.

2. Squeeze the white edge filler to the gap where the white edge appears, and the filler will automatically spread to both sides. If you can't get enough of the filler, you can use a very small, clean brush dipped in the filler and brush through the gaps.

3. When the filler is filled with white edges, you will find that the white edges of the mobile phone screen have disappeared. There are two ways to apply filler, one is to squeeze a small amount from left to right, and the other is to fill at intervals to allow the filler to spread slowly.

4. Finally, wipe the excess filler with a cleaning cloth, and be careful not to use too much force, so as not to squeeze out the filler in the gap and affect the effect.

When applying mobile phone film, if the mobile phone screen has a curvature, the outermost circle will often enter the air, resulting in white edges, which are not conforming and unsightly, and you can use white edge fillers to expel the air. White edge filler is a kind of grease product, which can be applied to the gap between the tempered film and the mobile phone screen to make the white edge disappear.

Summary. Hello! We are happy to answer your questions, the composition of regular white edge filler is silicone oil, which has no harm to the mobile phone screen, so users should carefully identify when choosing white edge filler, do not use fake and shoddy products, but white edge filler is easy to absorb dust after a period of use, and users need to clean up the mobile phone screen regularly.

How to use white edge filler: white edge filler is generally used after the mobile phone film, because some mobile phone films are not fully laminated, and most of the mobile phone screens use curved glass, which is very easy to appear when the film cannot be fitted, and injecting white edge filler into the edge of the screen can solve this problem.

Hello! We are happy to answer your questions, the ingredient of the regular white shed edge filler is silicone oil, which has no harm to the mobile phone screen, so the user should carefully identify the white edge filler when choosing the white edge filler, and do not use fake and shoddy products, but the white edge filler is easy to absorb dust after a period of use, and the user needs to clean the mobile phone screen regularly. How to use white edge filler:

White edge filler is generally used after the mobile phone film, because some mobile phone films are not fully bonded, and most of the screen of stupid Li mobile phones use curved glass, which is very easy to appear when the film can not be fitted, and injecting white edge filler into the edge of the screen can solve this problem.

Precautions for the use of white edge filler: 1. Do not use white edge filler if there is a crack in the mobile phone screen, because the white edge filler will damage the components if it penetrates into the inside of the mobile phone. 2. It is best to use the tools provided by the seller to apply the white edge filler, and it is not stupid to dump it directly on the mobile phone screen.

3. The white edge filler is essentially added to the white edge gap, if you squeeze the tempered film, you will find that the oil is squeezed out of the gap. 4. The white edge filler is only suitable for tempered film. However, if the mobile phone does not have a hand Sensun case, it is directly placed in the pocket, which is easy to cause the problem that the white edge filler is absorbed by the clothes.

Summary. 1. The white edge filler is silicone oil, which is not harmful to the screen. 2. When the white edge is engraved on the edge of the filling mobile phone, it will inevitably attach some fine dust of life, and the edge of the mobile phone will be contaminated with a lot of dust after a long time, and the edge of the mobile phone will be very dirty when you uncover the tempered film, and there is grease residue.

3. Secondly, this filler has permeability, for the edge of the mobile phone is not sealed, these greases will penetrate into the mobile phone, and over time it will definitely cause some damage to the internal parts of the mobile phone.

1. The white edge filler is silicone oil, which is not harmful to the screen. 2. When the white edge is engraved on the edge of the filling mobile phone, it will inevitably attach some fine dust of life, and the edge of the mobile phone will be contaminated with a lot of dust after a long time. 3. Secondly, this filler is permeable, for the edge of the mobile phone is not sealed, these greases will penetrate into the mobile phone, and over time it will definitely cause certain damage to the internal parts of the mobile phone.

It is recommended to use olive oil to remove the white edge, dip a toothpick in a toothpick, wipe along the edge of the tempered film, and gently warp to solve the white edge. The edge of the film is prone to white edges, which not only affects the appearance, but also causes dust to fall off the inside of the tempered film after a long time.

When applying the toughened film of the mobile phone, it is usually necessary to use the white edge filler to remove the white edge after the screen film. The steps are as follows:

3. When the filler is diffused and filled with white edges, it is found that the white edges of the mobile phone screen have disappeared, and there are two ways to apply the filler: one is to squeeze and fill the filler from left to right, but to fill it once at intervals, so that the filler can be slowly diffused and connected.

4. After applying the filler, use a cleaning cloth to wipe the excess filler, mainly do not use too much force, so as not to squeeze out the filler in the gap; In addition, the filler liquid is harmless to the mobile phone and the human body, so there is no need to worry about safety issues.

Summary. Dear, according to your description, I am giving you the answer - don't use white edge filler for mobile phone filmWhen sticking the film, it is best not to use white edge filler. Because white edge filler is a substance that can fill the gaps at the edges of the phone screen, it is often used to fill the gaps between the phone screen and the protective film that do not match the size.

However, there are also some problems and risks associated with the use of white edge fillers. First of all, it has a certain squeezing effect on the phone screen, which may cause the screen 3D Touch of some iPhone models after iPhone 6 to fail. Secondly, the white edge filler may affect the normal heat dissipation of the mobile phone and aggravate the heating phenomenon of the mobile phone.

In addition, if the white edge filler gets into the tiny crevices of the phone, it may cause a short circuit in the circuit, causing the phone to be damaged and unusable.

Dear, according to your description, I am giving you the answer - don't use white edge filler for mobile phone filmWhen sticking the film, it is best not to use white edge filler. Because white edge filler is a substance that can fill the gaps at the edges of the phone screen, it is often used to fill the gaps between the phone screen and the protective film that do not match the size. However, there are also some problems and risks associated with the use of white edge fillers.

First of all, it has a certain squeezing effect on the phone screen, which may cause the screen 3D Touch of some iPhone models after iPhone 6 to fail. Secondly, the white edge filler may affect the normal heat dissipation of the mobile phone and aggravate the heating phenomenon of the mobile phone. In addition, if the white edge filler gets into the tiny crevices of the phone, it may cause a short circuit in the circuit, causing the phone to be damaged and unusable.

Hello dear, in addition to avoiding the use of white edge filler, there are some other things to pay attention to: clean the screen: Before applying the film, you need to completely clean the mobile phone screen, otherwise the dirt and fingerprints on the screen will affect the effect of the film.

You can use a professional screen cleaner or an alcohol cotton ball to wipe the screen. Confirm the size of the film: When purchasing a film, make sure that the size of the film matches the size of your phone's screen to ensure that there are no gaps and edges that can cause dust, scratches, and brittleness.

Pay attention to the direction of the film: Before applying the film, confirm the direction and placement of the film, so as not to paste the wrong direction, waste the film, or affect the use of the mobile phone. Special Tools:

You can choose some special film application tools, such as suction cups, hooks, scrapers, etc., which can help us to better apply the film and avoid bubbles and wrinkles as much as possible.

Hello, dear, don't use white edge filler for mobile phone film: yes. Because the white edge filler will corrode the mobile phone screen, which will cause the mobile phone screen to crack, deform, etc.

At the same time, white edge filler may cause certain harm to human health. It is recommended that you choose a professional film brand when applying the film and pay attention to the instructions for use. Some brands of wraps will leave tiny white edges around the edges, which is normal and does not require the use of fillers.

In addition, in order to protect the mobile phone screen stove mold, you should also avoid putting the mobile phone together with other items, such as keys, coins, etc., to avoid scratching the screen. In conclusion, choose a professional film brand and avoid using white edge filler to better protect your phone screen.

1. The white edge filler cannot be pasted more firmly: because the viscosity of the white edge filler is smaller than the viscosity of the film, the liquid cannot stick the film and the surface of the mobile phone. 2. The white edge filler is not easy to flat

Because the fluidity of the white edge filler is too strong, it is easy to make the film slide, and it is impossible to stick the film on the mobile phone smoothly. 3. The white edge filler is easy to mold: because the white edge filler has no mildew resistance, it is easy to make the film moldy in a humid environment, which affects the appearance.

4. The white edge filler is not water-resistant: the white edge filler is not viscous enough, and there is no waterproof performance, once it encounters water, it will lift the film and affect the use effect. Be careful.