How to lock the sliding door of the kitchen balcony What lock How to install it

Lock with a crescent moon. Installation Method:

1.It is best to ask a master with experience in lock installation to install the lock. If you operate by yourself, please open the fixed distance template according to the installation requirements in the product manual.

2.Check whether the hole is accurate, load the lock body into the hole in turn, fix the screw after centering, install the screw and the connecting screw on the outer panel part, insert the linkage square rod into the square rod hole of the lock body, align the square hole of the handle of the outer panel part with the linkage square rod hole, install the outer panel component, and should strictly follow the steps in the product installation manual.

3.Install the inner panel parts, and tighten the screws after alignment; Insert the lock body into the lock hole of the lock body from the inside out; Insert the screws from the hole of the lock body panel and tighten them after threading the mounting hole of the lock body. Then install the lock box or lock plate on the door frame.

4. After the initial installation, turn the inner and outer handles of the crescent lock to observe whether the oblique tongue can be smoothly retracted and extended; Turn the knob on the rear panel to feel whether the square tongue is smoothly retracted; Insert the key and rotate it back and forth to feel whether the square tongue is smoothly stretched out and retracted.

5.After tightening the assembly screws of the crescent lock with a screwdriver, repeat the above action and turn it several times to ensure that the deadbolt can advance and retreat freely after the screws are fixed.

If you want to install locks on this sliding door, it can only be installed on both sides, and it is snap-on, and there should be professional installation in the nearby large building materials market.

1. Slide installation. Usually, when installing the sliding door, you need to install the sliding device, when installing the slide rail, you need to fix the door beam according to the width of the door and the opening direction, the center of the door width is used as a reference, and the two sides are fixed, it should be noted that the left and right height of the connection position between the sliding piece and the door beam needs to be the same, and the size of the sliding center line and the outer wall of the color plate needs to be consistent, and the size of the fan is preferably half of the thickness of the fan, which is 2mm larger than the gap.

2. Door leaf installation. The leaf and pulley system of the sliding door is generally formed directly in the factory, and after installing the slider, the pulley can be placed in the chutePlace vertically underneath by hand or other lifting tools; At the same time, the screw on the door is inserted into the bolt hole installed on the pulley for fixing, 3, the door limiter.

When installing the door of the sliding door, it is necessary to start installing the door capper, which needs to be welded to the bottom or inside of the upper slider using the angle steel cap, and make the door open at a distance of 10mm from the side of the pulley, this area is limited to its effective range, the contact position between the angle steel and the pulley must be set at 20mm or more, and the hard rubber pad can be used as a cushion in the middle, 4, the guide cake and the lower door limiter are installed. After the installation of the upper limit of the door is completed, the sliding door guide plate and the lower limit of the door can be activated; The center line of the guide cake can be positioned according to the actual position of the flat steel under the door leaf, and the guide cake needs to be exposed to the ground for about 10-15 mm, and the spacing is about 500 mm; When installing the lower limiter, the limb finger needs to push the door leaf to a position of 10-20mm from the outside, and then fix the stop with screws, 5. Door hardware installation. The hardware fittings of the sliding door are installed, the hardware fittings of the sliding door mainly include the handle and the lock, you must wait until the sliding door is installed and adjusted correctly before installation, the height and position of the fittings should be installed correctly to make the sliding door look more beautiful.

<>1. Install the slideway: first fix the door beam according to the opening direction of the sliding door and the width of the door opening, and the slideway should be based on the center of the door opening, and then divided into 2 sides for fixing.

2. Slideway fixing: when fixed, the height of the connection position between the door beam and the slideway should be kept the same, and the size of the outer wall of the color plate should be the same as the size of the center line of the slideway, and it is best to have a gap of two centimeters more than half of the thickness of the door leaf.

3. Install the pulley system and the door leaf: first put the pulley into the chute of the sliding door, and then lift the door leaf vertically to the bottom of the upper slideway, and at the same time, the screw of the door leaf should be inserted into it from the bolt hole of the pulley, and it should be fixed.

4. Install the door limiter of the sliding door: first, at a position about ten millimeters away from the edge of the pulley, use the angle steel limiter, and weld the inside or bottom of the upper slideway, so that the opening range of the sliding door is limited to an area. The contact position between the pulley and the angle steel should be set more than 20 mm.

1. First of all, when installing the slideway, the door beam should be fixed according to the opening direction of the sliding door and the width of the door opening.

2. Then install the pulley system and door leaf of the sliding door.

3. Then install the door limiter of the sliding door, use the angle steel limiter, and weld the inside or bottom of the upper slideway, so that the opening range of the sliding door is limited to an area.

4. Then install the lower door limiter and guide cake of the sliding door, when installing the lower door limiter, the door leaf of the sliding door should be pushed to a position about 20mm away from the outside, and then the lower door limiter should be fixed with screws.

5. Finally, install the hardware accessories of the sliding door.

If the sliding door in the kitchen is not installed properly, it will affect the use effect. So how to install the kitchen sliding door correctly? PChouse will take you to find out.

1. If you want to install the kitchen sliding door, then you should install the slide first. When installing the slideway, the door beam should be fixed according to the opening direction of the sliding door and the width of the door opening, and under normal circumstances, the slideway should be based on the center of the door opening, and then divided into 2 sides for fixing. When fixed, the height of the connection between the door beam and the slideway should be kept the same, and the size of the color plate exterior wall should be the same as the size of the center line of the slideway, preferably a gap of two centimeters more than half of the thickness of the door leaf.

2. After the upper slideway is installed, it is necessary to install the pulley system and door leaf of the sliding door. First, put the pulley into the chute of the sliding door, and then lift the door leaf vertically to the bottom of the upper slideway, and at the same time, the screw rod of the door leaf should be inserted from the bolt hole of the pulley, and it should be fixed.

3. After the pulley system and door leaf are installed, the door limiter of the sliding door should be installed. Approximately 10 mm from the edge of the pulley, the angle bar cap is used to weld the inside or bottom of the upper slide, so that the opening range of the sliding door is limited to one area. The contact position between the pulley and the angle should be set at a height of more than 20 mm, and a hard rubber pad should also be installed in the middle to provide a cushioning effect.

4. After the door limiter of the sliding door is installed, the lower door limiter and the guide cake of the sliding door should be installed. When installing the lower door limiter of the sliding door, you should first push the door leaf of the sliding door to a position about 20 mm away from the outside, and then use screws to fix the lower door limiter. When installing the guide cake, the center line of the guide cake should be determined with the position of the flat steel under the door leaf, which should generally be about 15 mm above the ground, and the distance between each other should be kept at 500 mm.