How to install the filter of Haier washing machine and how to distinguish between positive and negat

Before installing the washing machine, it is necessary to check whether the tools and materials required for installation are complete, mainly including power sockets, sockets, special faucets for washing machines, and water inlet pipes.

Step two. After checking the required materials, place the washing machine on a relatively flat and solid ground close to the power supply, faucet and floor drain, and adjust the feet at the bottom if it is tilted to make the washing machine stable.

Step 3. Before installing the water inlet pipe, make sure that the faucet mouth is flat, twist and adjust the four screws on the water inlet pipe joint outward, so that the interface is slightly larger than the faucet mouth, and the rubber pad on the water inlet pipe interface is close to the faucet mouth, and tighten the screws.

Finally, connect the other port of the inlet pipe to the interface of the washing machine.

Step 4. The installation method of the drain pipe is the same as that of the water inlet pipe, just connect the interface of the drain pipe with the drain of the washing machine, and put the floor drain at the other end.

Step five. After installing the water inlet pipe, everyone can proceed to the final step, turn on the power and check if the washing machine is working properly.

It is necessary to remind everyone to read the manual carefully and determine the precautions for installation and use on the manual, secondly, try to use the special water pipe for washing machines in the inlet and outlet pipes, and at the same time there should be air flow between the drainage pipe and the sewer, which can not be blocked and bent the drainage pipe.

This capacitor has no positive and negative poles, it is connected at will, it is just a filter to prevent sparks from interfering with other electrical appliances.

If you want to distinguish Haier washing machine from the fuselage, whether the drive is ordinary or not, you can take a look at its ***. Or is it his defense? Such. Be able to distinguish.

The appearance of Haier washing machines is almost the same, and you can only look at the manual and shopping guide to introduce it.

Haier washing machine should be divided into drivers or ordinary, in fact, it can be seen from the manual.

This is the easiest way to identify.

That is, if he vibrates particularly strongly when washing, it is more ordinary, but if he is more stable and quiet, it is more advanced.

How to distinguish whether the washing machine is driven or ordinary? You can take a look at the parameters displayed on the upper part of the fuselage.

Haier washing machine is a very ordinary one from the fuselage division.

It is not clear how Haier washing machines distinguish sunrises from the fuselage, which is ordinary.

The fuselage should be indistinguishable. You can only take its manual and look at its structure.

Capacitive running drum washing machine two-speed motor. YXG162 2 Please give the wiring diagram thanks again.

It's better to ask the after-sales service, they have information.

This individual can repair it, but it's too much trouble. The order is dismantled from the outside, from the inside to the outside. It takes more than 20 minutes for a skilled master to install this.

It is recommended to find after-sales service to deal with it better, and poor installation will lead to poor sealing and water leakage.

You open the back cover of the control box behind the washing machine, and then remove the laundry bucket network cover, you will see a nylon wire, the lower end is connected to the water glue cover, the upper end of the switch is connected to the switch, and the upper end of the positioning wheel has a spring, one end is connected to the switch, and the other end is connected to the nylon line.

It seems to have been installed by Haier after-sales!

Haha, you won't find a Haier after-sales one.

Don't fool around, otherwise it's troublesome to pretend badly!

To be honest, I can't do this kind of work.

You have to ask Haier after-sales to know!

You have to find a professional to do this.

It's hard to install it yourself.

I don't know, but it should be a good installation.

Or contact Haier customer service and say hello.

Isn't it clear that it's complicated to swap?

Haier customer service can ask them.

Yo, you ask Haier customer service about this.

Didn't Haier after-sales come to install it?

Where is this positioning spring?

I haven't installed it, does anyone know?

Steps to install a front-loading washing machine.

1. Remove the four fixing bolts on the back, take them out together with the rubber pads inside, and keep them.

2. Install the dust cover at the fixing bolt position and fix it with a plum screwdriver.

3. Open the door panel of the front panel and take out the two water pipes inside.

4. Install the drain pipe and fix the drain pipe at the drain with the clamp that comes with the washing machine. The same method is used to install the inlet pipe.

5. Energized, watered, tested, completed.

It can be installed, but it's actually not that difficult. Here's how to install it:

Then, put the washing machine in place, and adjust the level of the washing machine, the front two feet of the washing machine, can be rotated and adjusted, after adjustment, please lock, so as not to change the displacement due to vibration in future use.

The inlet pipe is connected to the drain pipe, and the water inlet pipe needs to be locked directly on the inlet faucet.

Finally, install a soundproof rodent panel.

This is actually convenient to remove when installing. Therefore, it is not installed directly when it leaves the factory.

The installation of the bottom plate, as shown in the manual, as long as it is installed according to the diagram, close the back cover.

In fact, now the installation is free, you can call customer service to arrange a time for on-site installation.

Hello, thank you for asking the company.

For washing machine products, it is best to look at the instructions when installing, because there is the most comprehensive installation process. Now we will introduce the whole process from the installation of the washing machine to the first use.

1. Check first when you open the package. After opening the outer packaging of the washing machine, you need to check whether the washing machine has been damaged during transportation, and check whether all the accessories are complete.

2. Remove the transport bolts. Before using the washing machine, be sure to remove the transport bolts on the back, otherwise the washing machine will not only be very noisy but also the body will shake very badly.

3. Choose a flat place for installation. Before installing the washing machine, the characteristics of the installation site must be hard, dry, and flat, and it should be protected from direct sunlight and away from heat sources such as gas. Never place the washing machine on a carpeted base.

4. If it is not stable, adjust the foot. After the washing machine is placed, check whether the washing machine shakes smoothly, if there is shaking, you can adjust the 4 feet until it is stable.

5. Use a special faucet for washing machines. There are special faucets for washing machines on the market**, you can first screw out the 4 screws on the joint, and then loosen the round plastic and circular metal ring on the joint, and then put the joint on the faucet and tighten the 4 screws, and finally tighten the round plastic and circular metal ring on the joint.

6. Keep the drainage pipe at a suitable height. In order to prevent the occurrence of siphoning, the installation height of the drain pipe should be between meters, and the end of the cut drain pipe should not be immersed in water.

7. The power connection should be safe and reliable. The safety and reliability of the power supply is the guarantee for the operation of the washing machine, to ensure that the voltage is consistent with the parameters and specifications on the washing machine, use more than 10A AC alone, and reasonably choose the fuse or fuse.

8. Clean the new washing machine before use. Since washing machines are inspected before leaving the factory, and then sealed and packaged to sell to consumers. Since there will be some residual moisture inside, which will cause some odors for a long time, it is best to clean up the new machine for the first time, such as running a program such as "barrel cleaning".

You are welcome to ask the company questions again.

We wish you a happy work life

This is Haier's after-sales service, and they are all responsible for the installation at the door.

Call ** to Haier's after-sales service, and they will come to install it.

Please follow the diagram below:

Washing machine] 1, washing machine is a cleaning appliance that uses electrical energy to produce mechanical action to wash clothes, and is divided into two categories according to its rated washing capacity: household and collective.

2. China stipulates that the washing capacity is less than 6 kg belongs to the household washing machine: the household washing machine is mainly composed of the box, the washing and dehydration bucket (some washing and dewatering barrels are separated), transmission and control systems, etc., and some are also equipped with heating devices. Washing machines generally refer to the use of water as the main cleaning liquid, as opposed to the use of special cleaning solutions, and the dry cleaning that is usually carried out by a dedicated person.